d461e96cd2
These are all the driver updates for SoC specific drivers. There are a couple of subsystems with individual maintainers picking up their patches here: - The reset controller subsystem add support for a few new SoC variants to existing drivers, along with other minor improvements - The OP-TEE subsystem gets a driver for the ARM FF-A transport - The memory controller subsystem has improvements for Tegra, Mediatek, Renesas, Freescale and Broadcom specific drivers. - The tegra cpuidle driver changes get merged through this tree this time. There are only minor changes, but they depend on other tegra driver updates here. - The ep93xx platform finally moves to using the drivers/clk/ subsystem, moving the code out of arch/arm in the process. This depends on a small sound driver change that is included here as well. - There are some minor updates for Qualcomm and Tegra specific firmware drivers. The other driver updates are mainly for drivers/soc, which contains a mixture of vendor specific drivers that don't really fit elsewhere: - Mediatek drivers gain more support for MT8192, with new support for hw-mutex and mmsys routing, plus support for reset lines in the mmsys driver. - Qualcomm gains a new "sleep stats" driver, and support for the "Generic Packet Router" in the APR driver. - There is a new user interface for routing the UARTS on ASpeed BMCs, something that apparently nobody else has needed so far. - More drivers can now be built as loadable modules, in particular for Broadcom and Samsung platforms. - Lots of improvements to the TI sysc driver for better suspend/resume support Finally, there are lots of minor cleanups and new device IDs for amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx, layerscape, allwinner, broadcom, and omap. -----BEGIN PGP SIGNATURE----- iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmGCvKgACgkQmmx57+YA GNnNfw/8DDTfMUycVvtaNslYlWri0/2O0nSqhNIIbTAcVuD/x5qo/McDhKuv+ldM BoTDMjRYZfQkrNXSEj3MaxB9E0o6Srva5SM8y4+Koe0VVtvEVovjYkXOhXqSEWWl aqVIe0S6Y1rF/KxJlvAfGxYHb5d+6aYqzdmhjURpXNGxqpSHb9/hqisY97Q9TpnD 6lQZOz9d1JNDq0eOh1qjcfuMjg1EHZHDZJyioCvyX38KIl2q7p3ll2z/eqrrDhQZ TrvL/YVosTXqBcAfi47Oz+n/CX2i0MrjVO8nfPSGOq5UL4Al3SZD4XYY96IOIQrH +XGFigGGAkV2LfKSEPNJWaq7g+SiQUr2jc3p8b4Zxde8/+5M127/gotiPddyG2LX 1OnFRnPskgRApGqHjGEcEzzJUTag7Hc+YVH82TMEHZhSDMq6i30k9UnyfXsziZDV 8CrkOpjuSg+YxFv/83bfa1pIoYtFfjGr16mq4muajodnX7+b7My9iv+2Oo2iQM9y DwRUKj7+eap23SEUpi4et6HlNpoF6yJMbt5Ae1k+gTK2DvQ4Cx6n4QJz/I7WC1Wp BdVhvSH8XVppVLtQqODud+VWvLgLerRxUpGRdbS8r5VsnNUJTvaS4YGMpm9616G7 TrgUSSvsyu1lLqbWMh+pOCk4l3r64vSUn581hrIw6jtioNGvMdE= =tUuj -----END PGP SIGNATURE----- Merge tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC driver updates from Arnd Bergmann: "These are all the driver updates for SoC specific drivers. There are a couple of subsystems with individual maintainers picking up their patches here: - The reset controller subsystem add support for a few new SoC variants to existing drivers, along with other minor improvements - The OP-TEE subsystem gets a driver for the ARM FF-A transport - The memory controller subsystem has improvements for Tegra, Mediatek, Renesas, Freescale and Broadcom specific drivers. - The tegra cpuidle driver changes get merged through this tree this time. There are only minor changes, but they depend on other tegra driver updates here. - The ep93xx platform finally moves to using the drivers/clk/ subsystem, moving the code out of arch/arm in the process. This depends on a small sound driver change that is included here as well. - There are some minor updates for Qualcomm and Tegra specific firmware drivers. The other driver updates are mainly for drivers/soc, which contains a mixture of vendor specific drivers that don't really fit elsewhere: - Mediatek drivers gain more support for MT8192, with new support for hw-mutex and mmsys routing, plus support for reset lines in the mmsys driver. - Qualcomm gains a new "sleep stats" driver, and support for the "Generic Packet Router" in the APR driver. - There is a new user interface for routing the UARTS on ASpeed BMCs, something that apparently nobody else has needed so far. - More drivers can now be built as loadable modules, in particular for Broadcom and Samsung platforms. - Lots of improvements to the TI sysc driver for better suspend/resume support" Finally, there are lots of minor cleanups and new device IDs for amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx, layerscape, allwinner, broadcom, and omap" * tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (179 commits) optee: Fix spelling mistake "reclain" -> "reclaim" Revert "firmware: qcom: scm: Add support for MC boot address API" qcom: spm: allow compile-testing firmware: arm_ffa: Remove unused 'compat_version' variable soc: samsung: exynos-chipid: add exynosautov9 SoC support firmware: qcom: scm: Don't break compile test on non-ARM platforms soc: qcom: smp2p: Add of_node_put() before goto soc: qcom: apr: Add of_node_put() before return soc: qcom: qcom_stats: Fix client votes offset soc: qcom: rpmhpd: fix sm8350_mxc's peer domain dt-bindings: arm: cpus: Document qcom,msm8916-smp enable-method ARM: qcom: Add qcom,msm8916-smp enable-method identical to MSM8226 firmware: qcom: scm: Add support for MC boot address API soc: qcom: spm: Add 8916 SPM register data dt-bindings: soc: qcom: spm: Document qcom,msm8916-saw2-v3.0-cpu soc: qcom: socinfo: Add PM8150C and SMB2351 models firmware: qcom_scm: Fix error retval in __qcom_scm_is_call_available() soc: aspeed: Add UART routing support soc: fsl: dpio: rename the enqueue descriptor variable soc: fsl: dpio: use an explicit NULL instead of 0 ...
519 lines
13 KiB
C
519 lines
13 KiB
C
// SPDX-License-Identifier: GPL-2.0-only
|
|
/*
|
|
* linux/sound/soc/ep93xx-i2s.c
|
|
* EP93xx I2S driver
|
|
*
|
|
* Copyright (C) 2010 Ryan Mallon
|
|
*
|
|
* Based on the original driver by:
|
|
* Copyright (C) 2007 Chase Douglas <chasedouglas@gmail>
|
|
* Copyright (C) 2006 Lennert Buytenhek <buytenh@wantstofly.org>
|
|
*/
|
|
|
|
#include <linux/module.h>
|
|
#include <linux/init.h>
|
|
#include <linux/slab.h>
|
|
#include <linux/clk.h>
|
|
#include <linux/io.h>
|
|
|
|
#include <sound/core.h>
|
|
#include <sound/dmaengine_pcm.h>
|
|
#include <sound/pcm.h>
|
|
#include <sound/pcm_params.h>
|
|
#include <sound/initval.h>
|
|
#include <sound/soc.h>
|
|
|
|
#include <linux/platform_data/dma-ep93xx.h>
|
|
#include <linux/soc/cirrus/ep93xx.h>
|
|
|
|
#include "ep93xx-pcm.h"
|
|
|
|
#define EP93XX_I2S_TXCLKCFG 0x00
|
|
#define EP93XX_I2S_RXCLKCFG 0x04
|
|
#define EP93XX_I2S_GLSTS 0x08
|
|
#define EP93XX_I2S_GLCTRL 0x0C
|
|
|
|
#define EP93XX_I2S_I2STX0LFT 0x10
|
|
#define EP93XX_I2S_I2STX0RT 0x14
|
|
|
|
#define EP93XX_I2S_TXLINCTRLDATA 0x28
|
|
#define EP93XX_I2S_TXCTRL 0x2C
|
|
#define EP93XX_I2S_TXWRDLEN 0x30
|
|
#define EP93XX_I2S_TX0EN 0x34
|
|
|
|
#define EP93XX_I2S_RXLINCTRLDATA 0x58
|
|
#define EP93XX_I2S_RXCTRL 0x5C
|
|
#define EP93XX_I2S_RXWRDLEN 0x60
|
|
#define EP93XX_I2S_RX0EN 0x64
|
|
|
|
#define EP93XX_I2S_WRDLEN_16 (0 << 0)
|
|
#define EP93XX_I2S_WRDLEN_24 (1 << 0)
|
|
#define EP93XX_I2S_WRDLEN_32 (2 << 0)
|
|
|
|
#define EP93XX_I2S_RXLINCTRLDATA_R_JUST BIT(1) /* Right justify */
|
|
|
|
#define EP93XX_I2S_TXLINCTRLDATA_R_JUST BIT(2) /* Right justify */
|
|
|
|
/*
|
|
* Transmit empty interrupt level select:
|
|
* 0 - Generate interrupt when FIFO is half empty
|
|
* 1 - Generate interrupt when FIFO is empty
|
|
*/
|
|
#define EP93XX_I2S_TXCTRL_TXEMPTY_LVL BIT(0)
|
|
#define EP93XX_I2S_TXCTRL_TXUFIE BIT(1) /* Transmit interrupt enable */
|
|
|
|
#define EP93XX_I2S_CLKCFG_LRS (1 << 0) /* lrclk polarity */
|
|
#define EP93XX_I2S_CLKCFG_CKP (1 << 1) /* Bit clock polarity */
|
|
#define EP93XX_I2S_CLKCFG_REL (1 << 2) /* First bit transition */
|
|
#define EP93XX_I2S_CLKCFG_MASTER (1 << 3) /* Master mode */
|
|
#define EP93XX_I2S_CLKCFG_NBCG (1 << 4) /* Not bit clock gating */
|
|
|
|
#define EP93XX_I2S_GLSTS_TX0_FIFO_FULL BIT(12)
|
|
|
|
struct ep93xx_i2s_info {
|
|
struct clk *mclk;
|
|
struct clk *sclk;
|
|
struct clk *lrclk;
|
|
void __iomem *regs;
|
|
struct snd_dmaengine_dai_dma_data dma_params_rx;
|
|
struct snd_dmaengine_dai_dma_data dma_params_tx;
|
|
};
|
|
|
|
static struct ep93xx_dma_data ep93xx_i2s_dma_data[] = {
|
|
[SNDRV_PCM_STREAM_PLAYBACK] = {
|
|
.name = "i2s-pcm-out",
|
|
.port = EP93XX_DMA_I2S1,
|
|
.direction = DMA_MEM_TO_DEV,
|
|
},
|
|
[SNDRV_PCM_STREAM_CAPTURE] = {
|
|
.name = "i2s-pcm-in",
|
|
.port = EP93XX_DMA_I2S1,
|
|
.direction = DMA_DEV_TO_MEM,
|
|
},
|
|
};
|
|
|
|
static inline void ep93xx_i2s_write_reg(struct ep93xx_i2s_info *info,
|
|
unsigned reg, unsigned val)
|
|
{
|
|
__raw_writel(val, info->regs + reg);
|
|
}
|
|
|
|
static inline unsigned ep93xx_i2s_read_reg(struct ep93xx_i2s_info *info,
|
|
unsigned reg)
|
|
{
|
|
return __raw_readl(info->regs + reg);
|
|
}
|
|
|
|
static void ep93xx_i2s_enable(struct ep93xx_i2s_info *info, int stream)
|
|
{
|
|
unsigned base_reg;
|
|
|
|
if ((ep93xx_i2s_read_reg(info, EP93XX_I2S_TX0EN) & 0x1) == 0 &&
|
|
(ep93xx_i2s_read_reg(info, EP93XX_I2S_RX0EN) & 0x1) == 0) {
|
|
/* Enable clocks */
|
|
clk_prepare_enable(info->mclk);
|
|
clk_prepare_enable(info->sclk);
|
|
clk_prepare_enable(info->lrclk);
|
|
|
|
/* Enable i2s */
|
|
ep93xx_i2s_write_reg(info, EP93XX_I2S_GLCTRL, 1);
|
|
}
|
|
|
|
/* Enable fifo */
|
|
if (stream == SNDRV_PCM_STREAM_PLAYBACK)
|
|
base_reg = EP93XX_I2S_TX0EN;
|
|
else
|
|
base_reg = EP93XX_I2S_RX0EN;
|
|
ep93xx_i2s_write_reg(info, base_reg, 1);
|
|
|
|
/* Enable TX IRQs (FIFO empty or underflow) */
|
|
if (IS_ENABLED(CONFIG_SND_EP93XX_SOC_I2S_WATCHDOG) &&
|
|
stream == SNDRV_PCM_STREAM_PLAYBACK)
|
|
ep93xx_i2s_write_reg(info, EP93XX_I2S_TXCTRL,
|
|
EP93XX_I2S_TXCTRL_TXEMPTY_LVL |
|
|
EP93XX_I2S_TXCTRL_TXUFIE);
|
|
}
|
|
|
|
static void ep93xx_i2s_disable(struct ep93xx_i2s_info *info, int stream)
|
|
{
|
|
unsigned base_reg;
|
|
|
|
/* Disable IRQs */
|
|
if (IS_ENABLED(CONFIG_SND_EP93XX_SOC_I2S_WATCHDOG) &&
|
|
stream == SNDRV_PCM_STREAM_PLAYBACK)
|
|
ep93xx_i2s_write_reg(info, EP93XX_I2S_TXCTRL, 0);
|
|
|
|
/* Disable fifo */
|
|
if (stream == SNDRV_PCM_STREAM_PLAYBACK)
|
|
base_reg = EP93XX_I2S_TX0EN;
|
|
else
|
|
base_reg = EP93XX_I2S_RX0EN;
|
|
ep93xx_i2s_write_reg(info, base_reg, 0);
|
|
|
|
if ((ep93xx_i2s_read_reg(info, EP93XX_I2S_TX0EN) & 0x1) == 0 &&
|
|
(ep93xx_i2s_read_reg(info, EP93XX_I2S_RX0EN) & 0x1) == 0) {
|
|
/* Disable i2s */
|
|
ep93xx_i2s_write_reg(info, EP93XX_I2S_GLCTRL, 0);
|
|
|
|
/* Disable clocks */
|
|
clk_disable_unprepare(info->lrclk);
|
|
clk_disable_unprepare(info->sclk);
|
|
clk_disable_unprepare(info->mclk);
|
|
}
|
|
}
|
|
|
|
/*
|
|
* According to documentation I2S controller can handle underflow conditions
|
|
* just fine, but in reality the state machine is sometimes confused so that
|
|
* the whole stream is shifted by one byte. The watchdog below disables the TX
|
|
* FIFO, fills the buffer with zeroes and re-enables the FIFO. State machine
|
|
* is being reset and by filling the buffer we get some time before next
|
|
* underflow happens.
|
|
*/
|
|
static irqreturn_t ep93xx_i2s_interrupt(int irq, void *dev_id)
|
|
{
|
|
struct ep93xx_i2s_info *info = dev_id;
|
|
|
|
/* Disable FIFO */
|
|
ep93xx_i2s_write_reg(info, EP93XX_I2S_TX0EN, 0);
|
|
/*
|
|
* Fill TX FIFO with zeroes, this way we can defer next IRQs as much as
|
|
* possible and get more time for DMA to catch up. Actually there are
|
|
* only 8 samples in this FIFO, so even on 8kHz maximum deferral here is
|
|
* 1ms.
|
|
*/
|
|
while (!(ep93xx_i2s_read_reg(info, EP93XX_I2S_GLSTS) &
|
|
EP93XX_I2S_GLSTS_TX0_FIFO_FULL)) {
|
|
ep93xx_i2s_write_reg(info, EP93XX_I2S_I2STX0LFT, 0);
|
|
ep93xx_i2s_write_reg(info, EP93XX_I2S_I2STX0RT, 0);
|
|
}
|
|
/* Re-enable FIFO */
|
|
ep93xx_i2s_write_reg(info, EP93XX_I2S_TX0EN, 1);
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static int ep93xx_i2s_dai_probe(struct snd_soc_dai *dai)
|
|
{
|
|
struct ep93xx_i2s_info *info = snd_soc_dai_get_drvdata(dai);
|
|
|
|
info->dma_params_tx.filter_data =
|
|
&ep93xx_i2s_dma_data[SNDRV_PCM_STREAM_PLAYBACK];
|
|
info->dma_params_rx.filter_data =
|
|
&ep93xx_i2s_dma_data[SNDRV_PCM_STREAM_CAPTURE];
|
|
|
|
dai->playback_dma_data = &info->dma_params_tx;
|
|
dai->capture_dma_data = &info->dma_params_rx;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void ep93xx_i2s_shutdown(struct snd_pcm_substream *substream,
|
|
struct snd_soc_dai *dai)
|
|
{
|
|
struct ep93xx_i2s_info *info = snd_soc_dai_get_drvdata(dai);
|
|
|
|
ep93xx_i2s_disable(info, substream->stream);
|
|
}
|
|
|
|
static int ep93xx_i2s_set_dai_fmt(struct snd_soc_dai *cpu_dai,
|
|
unsigned int fmt)
|
|
{
|
|
struct ep93xx_i2s_info *info = snd_soc_dai_get_drvdata(cpu_dai);
|
|
unsigned int clk_cfg;
|
|
unsigned int txlin_ctrl = 0;
|
|
unsigned int rxlin_ctrl = 0;
|
|
|
|
clk_cfg = ep93xx_i2s_read_reg(info, EP93XX_I2S_RXCLKCFG);
|
|
|
|
switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
|
|
case SND_SOC_DAIFMT_I2S:
|
|
clk_cfg |= EP93XX_I2S_CLKCFG_REL;
|
|
break;
|
|
|
|
case SND_SOC_DAIFMT_LEFT_J:
|
|
clk_cfg &= ~EP93XX_I2S_CLKCFG_REL;
|
|
break;
|
|
|
|
case SND_SOC_DAIFMT_RIGHT_J:
|
|
clk_cfg &= ~EP93XX_I2S_CLKCFG_REL;
|
|
rxlin_ctrl |= EP93XX_I2S_RXLINCTRLDATA_R_JUST;
|
|
txlin_ctrl |= EP93XX_I2S_TXLINCTRLDATA_R_JUST;
|
|
break;
|
|
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
|
|
switch (fmt & SND_SOC_DAIFMT_CLOCK_PROVIDER_MASK) {
|
|
case SND_SOC_DAIFMT_CBC_CFC:
|
|
/* CPU is provider */
|
|
clk_cfg |= EP93XX_I2S_CLKCFG_MASTER;
|
|
break;
|
|
|
|
case SND_SOC_DAIFMT_CBP_CFP:
|
|
/* Codec is provider */
|
|
clk_cfg &= ~EP93XX_I2S_CLKCFG_MASTER;
|
|
break;
|
|
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
|
|
switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
|
|
case SND_SOC_DAIFMT_NB_NF:
|
|
/* Negative bit clock, lrclk low on left word */
|
|
clk_cfg &= ~(EP93XX_I2S_CLKCFG_CKP | EP93XX_I2S_CLKCFG_LRS);
|
|
break;
|
|
|
|
case SND_SOC_DAIFMT_NB_IF:
|
|
/* Negative bit clock, lrclk low on right word */
|
|
clk_cfg &= ~EP93XX_I2S_CLKCFG_CKP;
|
|
clk_cfg |= EP93XX_I2S_CLKCFG_LRS;
|
|
break;
|
|
|
|
case SND_SOC_DAIFMT_IB_NF:
|
|
/* Positive bit clock, lrclk low on left word */
|
|
clk_cfg |= EP93XX_I2S_CLKCFG_CKP;
|
|
clk_cfg &= ~EP93XX_I2S_CLKCFG_LRS;
|
|
break;
|
|
|
|
case SND_SOC_DAIFMT_IB_IF:
|
|
/* Positive bit clock, lrclk low on right word */
|
|
clk_cfg |= EP93XX_I2S_CLKCFG_CKP | EP93XX_I2S_CLKCFG_LRS;
|
|
break;
|
|
}
|
|
|
|
/* Write new register values */
|
|
ep93xx_i2s_write_reg(info, EP93XX_I2S_RXCLKCFG, clk_cfg);
|
|
ep93xx_i2s_write_reg(info, EP93XX_I2S_TXCLKCFG, clk_cfg);
|
|
ep93xx_i2s_write_reg(info, EP93XX_I2S_RXLINCTRLDATA, rxlin_ctrl);
|
|
ep93xx_i2s_write_reg(info, EP93XX_I2S_TXLINCTRLDATA, txlin_ctrl);
|
|
return 0;
|
|
}
|
|
|
|
static int ep93xx_i2s_hw_params(struct snd_pcm_substream *substream,
|
|
struct snd_pcm_hw_params *params,
|
|
struct snd_soc_dai *dai)
|
|
{
|
|
struct ep93xx_i2s_info *info = snd_soc_dai_get_drvdata(dai);
|
|
unsigned word_len, div, sdiv, lrdiv;
|
|
int err;
|
|
|
|
switch (params_format(params)) {
|
|
case SNDRV_PCM_FORMAT_S16_LE:
|
|
word_len = EP93XX_I2S_WRDLEN_16;
|
|
break;
|
|
|
|
case SNDRV_PCM_FORMAT_S24_LE:
|
|
word_len = EP93XX_I2S_WRDLEN_24;
|
|
break;
|
|
|
|
case SNDRV_PCM_FORMAT_S32_LE:
|
|
word_len = EP93XX_I2S_WRDLEN_32;
|
|
break;
|
|
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
|
|
ep93xx_i2s_write_reg(info, EP93XX_I2S_TXWRDLEN, word_len);
|
|
else
|
|
ep93xx_i2s_write_reg(info, EP93XX_I2S_RXWRDLEN, word_len);
|
|
|
|
/*
|
|
* EP93xx I2S module can be setup so SCLK / LRCLK value can be
|
|
* 32, 64, 128. MCLK / SCLK value can be 2 and 4.
|
|
* We set LRCLK equal to `rate' and minimum SCLK / LRCLK
|
|
* value is 64, because our sample size is 32 bit * 2 channels.
|
|
* I2S standard permits us to transmit more bits than
|
|
* the codec uses.
|
|
*/
|
|
div = clk_get_rate(info->mclk) / params_rate(params);
|
|
sdiv = 4;
|
|
if (div > (256 + 512) / 2) {
|
|
lrdiv = 128;
|
|
} else {
|
|
lrdiv = 64;
|
|
if (div < (128 + 256) / 2)
|
|
sdiv = 2;
|
|
}
|
|
|
|
err = clk_set_rate(info->sclk, clk_get_rate(info->mclk) / sdiv);
|
|
if (err)
|
|
return err;
|
|
|
|
err = clk_set_rate(info->lrclk, clk_get_rate(info->sclk) / lrdiv);
|
|
if (err)
|
|
return err;
|
|
|
|
ep93xx_i2s_enable(info, substream->stream);
|
|
return 0;
|
|
}
|
|
|
|
static int ep93xx_i2s_set_sysclk(struct snd_soc_dai *cpu_dai, int clk_id,
|
|
unsigned int freq, int dir)
|
|
{
|
|
struct ep93xx_i2s_info *info = snd_soc_dai_get_drvdata(cpu_dai);
|
|
|
|
if (dir == SND_SOC_CLOCK_IN || clk_id != 0)
|
|
return -EINVAL;
|
|
|
|
return clk_set_rate(info->mclk, freq);
|
|
}
|
|
|
|
#ifdef CONFIG_PM
|
|
static int ep93xx_i2s_suspend(struct snd_soc_component *component)
|
|
{
|
|
struct ep93xx_i2s_info *info = snd_soc_component_get_drvdata(component);
|
|
|
|
if (!snd_soc_component_active(component))
|
|
return 0;
|
|
|
|
ep93xx_i2s_disable(info, SNDRV_PCM_STREAM_PLAYBACK);
|
|
ep93xx_i2s_disable(info, SNDRV_PCM_STREAM_CAPTURE);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ep93xx_i2s_resume(struct snd_soc_component *component)
|
|
{
|
|
struct ep93xx_i2s_info *info = snd_soc_component_get_drvdata(component);
|
|
|
|
if (!snd_soc_component_active(component))
|
|
return 0;
|
|
|
|
ep93xx_i2s_enable(info, SNDRV_PCM_STREAM_PLAYBACK);
|
|
ep93xx_i2s_enable(info, SNDRV_PCM_STREAM_CAPTURE);
|
|
|
|
return 0;
|
|
}
|
|
#else
|
|
#define ep93xx_i2s_suspend NULL
|
|
#define ep93xx_i2s_resume NULL
|
|
#endif
|
|
|
|
static const struct snd_soc_dai_ops ep93xx_i2s_dai_ops = {
|
|
.shutdown = ep93xx_i2s_shutdown,
|
|
.hw_params = ep93xx_i2s_hw_params,
|
|
.set_sysclk = ep93xx_i2s_set_sysclk,
|
|
.set_fmt = ep93xx_i2s_set_dai_fmt,
|
|
};
|
|
|
|
#define EP93XX_I2S_FORMATS (SNDRV_PCM_FMTBIT_S32_LE)
|
|
|
|
static struct snd_soc_dai_driver ep93xx_i2s_dai = {
|
|
.symmetric_rate = 1,
|
|
.probe = ep93xx_i2s_dai_probe,
|
|
.playback = {
|
|
.channels_min = 2,
|
|
.channels_max = 2,
|
|
.rates = SNDRV_PCM_RATE_8000_192000,
|
|
.formats = EP93XX_I2S_FORMATS,
|
|
},
|
|
.capture = {
|
|
.channels_min = 2,
|
|
.channels_max = 2,
|
|
.rates = SNDRV_PCM_RATE_8000_192000,
|
|
.formats = EP93XX_I2S_FORMATS,
|
|
},
|
|
.ops = &ep93xx_i2s_dai_ops,
|
|
};
|
|
|
|
static const struct snd_soc_component_driver ep93xx_i2s_component = {
|
|
.name = "ep93xx-i2s",
|
|
.suspend = ep93xx_i2s_suspend,
|
|
.resume = ep93xx_i2s_resume,
|
|
};
|
|
|
|
static int ep93xx_i2s_probe(struct platform_device *pdev)
|
|
{
|
|
struct ep93xx_i2s_info *info;
|
|
int err;
|
|
|
|
info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL);
|
|
if (!info)
|
|
return -ENOMEM;
|
|
|
|
info->regs = devm_platform_ioremap_resource(pdev, 0);
|
|
if (IS_ERR(info->regs))
|
|
return PTR_ERR(info->regs);
|
|
|
|
if (IS_ENABLED(CONFIG_SND_EP93XX_SOC_I2S_WATCHDOG)) {
|
|
int irq = platform_get_irq(pdev, 0);
|
|
if (irq <= 0)
|
|
return irq < 0 ? irq : -ENODEV;
|
|
|
|
err = devm_request_irq(&pdev->dev, irq, ep93xx_i2s_interrupt, 0,
|
|
pdev->name, info);
|
|
if (err)
|
|
return err;
|
|
}
|
|
|
|
info->mclk = clk_get(&pdev->dev, "mclk");
|
|
if (IS_ERR(info->mclk)) {
|
|
err = PTR_ERR(info->mclk);
|
|
goto fail;
|
|
}
|
|
|
|
info->sclk = clk_get(&pdev->dev, "sclk");
|
|
if (IS_ERR(info->sclk)) {
|
|
err = PTR_ERR(info->sclk);
|
|
goto fail_put_mclk;
|
|
}
|
|
|
|
info->lrclk = clk_get(&pdev->dev, "lrclk");
|
|
if (IS_ERR(info->lrclk)) {
|
|
err = PTR_ERR(info->lrclk);
|
|
goto fail_put_sclk;
|
|
}
|
|
|
|
dev_set_drvdata(&pdev->dev, info);
|
|
|
|
err = devm_snd_soc_register_component(&pdev->dev, &ep93xx_i2s_component,
|
|
&ep93xx_i2s_dai, 1);
|
|
if (err)
|
|
goto fail_put_lrclk;
|
|
|
|
err = devm_ep93xx_pcm_platform_register(&pdev->dev);
|
|
if (err)
|
|
goto fail_put_lrclk;
|
|
|
|
return 0;
|
|
|
|
fail_put_lrclk:
|
|
clk_put(info->lrclk);
|
|
fail_put_sclk:
|
|
clk_put(info->sclk);
|
|
fail_put_mclk:
|
|
clk_put(info->mclk);
|
|
fail:
|
|
return err;
|
|
}
|
|
|
|
static int ep93xx_i2s_remove(struct platform_device *pdev)
|
|
{
|
|
struct ep93xx_i2s_info *info = dev_get_drvdata(&pdev->dev);
|
|
|
|
clk_put(info->lrclk);
|
|
clk_put(info->sclk);
|
|
clk_put(info->mclk);
|
|
return 0;
|
|
}
|
|
|
|
static struct platform_driver ep93xx_i2s_driver = {
|
|
.probe = ep93xx_i2s_probe,
|
|
.remove = ep93xx_i2s_remove,
|
|
.driver = {
|
|
.name = "ep93xx-i2s",
|
|
},
|
|
};
|
|
|
|
module_platform_driver(ep93xx_i2s_driver);
|
|
|
|
MODULE_ALIAS("platform:ep93xx-i2s");
|
|
MODULE_AUTHOR("Ryan Mallon");
|
|
MODULE_DESCRIPTION("EP93XX I2S driver");
|
|
MODULE_LICENSE("GPL");
|