iv/linux
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
linux/drivers/net/dsa/sja1105/sja1105_clocking.c
Vladimir Oltean cb5a82d2b9 net: dsa: sja1105: properly power down the microcontroller clock for SJA1110 
It turns out that powering down the BASE_TIMER_CLK does not turn off the
microcontroller, just its timers, including the one for the watchdog.
So the embedded microcontroller is still running, and potentially still
doing things.

To prevent unwanted interference, we should power down the BASE_MCSS_CLK
as well (MCSS = microcontroller subsystem).

The trouble is that currently we turn off the BASE_TIMER_CLK for SJA1110
from the .clocking_setup() method, mostly because this is a Clock
Generation Unit (CGU) setting which was traditionally configured in that
method for SJA1105. But in SJA1105, the CGU was used for bringing up the
port clocks at the proper speeds, and in SJA1110 it's not (but rather
for initial configuration), so it's best that we rebrand the
sja1110_clocking_setup() method into what it really is - an implementation
of the .disable_microcontroller() method.

Since disabling the microcontroller only needs to be done once, at probe
time, we can choose the best place to do that as being in sja1105_setup(),
before we upload the static config to the device. This guarantees that
the static config being used by the switch afterwards is really ours.

Note that the procedure to upload a static config necessarily resets the
switch. This already did not reset the microcontroller, only the switch
core, so since the .disable_microcontroller() method is guaranteed to be
called by that point, if it's disabled, it remains disabled. Add a
comment to make that clear.

With the code movement for SJA1110 from .clocking_setup() to
.disable_microcontroller(), both methods are optional and are guarded by
"if" conditions.

Tested by enabling in the device tree the rev-mii switch port 0 that
goes towards the microcontroller, and flashing a firmware that would
have networking. Without this patch, the microcontroller can be pinged,
with this patch it cannot.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-18 12:26:17 -07:00

863 lines
25 KiB
C
Raw Blame History

// SPDX-License-Identifier: BSD-3-Clause
/* Copyright (c) 2016-2018, NXP Semiconductors
* Copyright (c) 2018-2019, Vladimir Oltean <olteanv@gmail.com>
*/
#include <linux/packing.h>
#include "sja1105.h"
#define SJA1105_SIZE_CGU_CMD 4
#define SJA1110_BASE_MCSS_CLK SJA1110_CGU_ADDR(0x70)
#define SJA1110_BASE_TIMER_CLK SJA1110_CGU_ADDR(0x74)
/* Common structure for CFG_PAD_MIIx_RX and CFG_PAD_MIIx_TX */
struct sja1105_cfg_pad_mii {
u64 d32_os;
u64 d32_ih;
u64 d32_ipud;
u64 d10_ih;
u64 d10_os;
u64 d10_ipud;
u64 ctrl_os;
u64 ctrl_ih;
u64 ctrl_ipud;
u64 clk_os;
u64 clk_ih;
u64 clk_ipud;
};
struct sja1105_cfg_pad_mii_id {
u64 rxc_stable_ovr;
u64 rxc_delay;
u64 rxc_bypass;
u64 rxc_pd;
u64 txc_stable_ovr;
u64 txc_delay;
u64 txc_bypass;
u64 txc_pd;
};
/* UM10944 Table 82.
* IDIV_0_C to IDIV_4_C control registers
* (addr. 10000Bh to 10000Fh)
*/
struct sja1105_cgu_idiv {
u64 clksrc;
u64 autoblock;
u64 idiv;
u64 pd;
};
/* PLL_1_C control register
*
* SJA1105 E/T: UM10944 Table 81 (address 10000Ah)
* SJA1105 P/Q/R/S: UM11040 Table 116 (address 10000Ah)
*/
struct sja1105_cgu_pll_ctrl {
u64 pllclksrc;
u64 msel;
u64 autoblock;
u64 psel;
u64 direct;
u64 fbsel;
u64 bypass;
u64 pd;
};
struct sja1110_cgu_outclk {
u64 clksrc;
u64 autoblock;
u64 pd;
};
enum {
CLKSRC_MII0_TX_CLK = 0x00,
CLKSRC_MII0_RX_CLK = 0x01,
CLKSRC_MII1_TX_CLK = 0x02,
CLKSRC_MII1_RX_CLK = 0x03,
CLKSRC_MII2_TX_CLK = 0x04,
CLKSRC_MII2_RX_CLK = 0x05,
CLKSRC_MII3_TX_CLK = 0x06,
CLKSRC_MII3_RX_CLK = 0x07,
CLKSRC_MII4_TX_CLK = 0x08,
CLKSRC_MII4_RX_CLK = 0x09,
CLKSRC_PLL0 = 0x0B,
CLKSRC_PLL1 = 0x0E,
CLKSRC_IDIV0 = 0x11,
CLKSRC_IDIV1 = 0x12,
CLKSRC_IDIV2 = 0x13,
CLKSRC_IDIV3 = 0x14,
CLKSRC_IDIV4 = 0x15,
};
/* UM10944 Table 83.
* MIIx clock control registers 1 to 30
* (addresses 100013h to 100035h)
*/
struct sja1105_cgu_mii_ctrl {
u64 clksrc;
u64 autoblock;
u64 pd;
};
static void sja1105_cgu_idiv_packing(void *buf, struct sja1105_cgu_idiv *idiv,
enum packing_op op)
{
const int size = 4;
sja1105_packing(buf, &idiv->clksrc, 28, 24, size, op);
sja1105_packing(buf, &idiv->autoblock, 11, 11, size, op);
sja1105_packing(buf, &idiv->idiv, 5, 2, size, op);
sja1105_packing(buf, &idiv->pd, 0, 0, size, op);
}
static int sja1105_cgu_idiv_config(struct sja1105_private *priv, int port,
bool enabled, int factor)
{
const struct sja1105_regs *regs = priv->info->regs;
struct device *dev = priv->ds->dev;
struct sja1105_cgu_idiv idiv;
u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0};
if (regs->cgu_idiv[port] == SJA1105_RSV_ADDR)
return 0;
if (enabled && factor != 1 && factor != 10) {
dev_err(dev, "idiv factor must be 1 or 10\n");
return -ERANGE;
}
/* Payload for packed_buf */
idiv.clksrc = 0x0A; /* 25MHz */
idiv.autoblock = 1; /* Block clk automatically */
idiv.idiv = factor - 1; /* Divide by 1 or 10 */
idiv.pd = enabled ? 0 : 1; /* Power down? */
sja1105_cgu_idiv_packing(packed_buf, &idiv, PACK);
return sja1105_xfer_buf(priv, SPI_WRITE, regs->cgu_idiv[port],
packed_buf, SJA1105_SIZE_CGU_CMD);
}
static void
sja1105_cgu_mii_control_packing(void *buf, struct sja1105_cgu_mii_ctrl *cmd,
enum packing_op op)
{
const int size = 4;
sja1105_packing(buf, &cmd->clksrc, 28, 24, size, op);
sja1105_packing(buf, &cmd->autoblock, 11, 11, size, op);
sja1105_packing(buf, &cmd->pd, 0, 0, size, op);
}
static int sja1105_cgu_mii_tx_clk_config(struct sja1105_private *priv,
int port, sja1105_mii_role_t role)
{
const struct sja1105_regs *regs = priv->info->regs;
struct sja1105_cgu_mii_ctrl mii_tx_clk;
const int mac_clk_sources[] = {
CLKSRC_MII0_TX_CLK,
CLKSRC_MII1_TX_CLK,
CLKSRC_MII2_TX_CLK,
CLKSRC_MII3_TX_CLK,
CLKSRC_MII4_TX_CLK,
};
const int phy_clk_sources[] = {
CLKSRC_IDIV0,
CLKSRC_IDIV1,
CLKSRC_IDIV2,
CLKSRC_IDIV3,
CLKSRC_IDIV4,
};
u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0};
int clksrc;
if (regs->mii_tx_clk[port] == SJA1105_RSV_ADDR)
return 0;
if (role == XMII_MAC)
clksrc = mac_clk_sources[port];
else
clksrc = phy_clk_sources[port];
/* Payload for packed_buf */
mii_tx_clk.clksrc = clksrc;
mii_tx_clk.autoblock = 1; /* Autoblock clk while changing clksrc */
mii_tx_clk.pd = 0; /* Power Down off => enabled */
sja1105_cgu_mii_control_packing(packed_buf, &mii_tx_clk, PACK);
return sja1105_xfer_buf(priv, SPI_WRITE, regs->mii_tx_clk[port],
packed_buf, SJA1105_SIZE_CGU_CMD);
}
static int
sja1105_cgu_mii_rx_clk_config(struct sja1105_private *priv, int port)
{
const struct sja1105_regs *regs = priv->info->regs;
struct sja1105_cgu_mii_ctrl mii_rx_clk;
u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0};
const int clk_sources[] = {
CLKSRC_MII0_RX_CLK,
CLKSRC_MII1_RX_CLK,
CLKSRC_MII2_RX_CLK,
CLKSRC_MII3_RX_CLK,
CLKSRC_MII4_RX_CLK,
};
if (regs->mii_rx_clk[port] == SJA1105_RSV_ADDR)
return 0;
/* Payload for packed_buf */
mii_rx_clk.clksrc = clk_sources[port];
mii_rx_clk.autoblock = 1; /* Autoblock clk while changing clksrc */
mii_rx_clk.pd = 0; /* Power Down off => enabled */
sja1105_cgu_mii_control_packing(packed_buf, &mii_rx_clk, PACK);
return sja1105_xfer_buf(priv, SPI_WRITE, regs->mii_rx_clk[port],
packed_buf, SJA1105_SIZE_CGU_CMD);
}
static int
sja1105_cgu_mii_ext_tx_clk_config(struct sja1105_private *priv, int port)
{
const struct sja1105_regs *regs = priv->info->regs;
struct sja1105_cgu_mii_ctrl mii_ext_tx_clk;
u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0};
const int clk_sources[] = {
CLKSRC_IDIV0,
CLKSRC_IDIV1,
CLKSRC_IDIV2,
CLKSRC_IDIV3,
CLKSRC_IDIV4,
};
if (regs->mii_ext_tx_clk[port] == SJA1105_RSV_ADDR)
return 0;
/* Payload for packed_buf */
mii_ext_tx_clk.clksrc = clk_sources[port];
mii_ext_tx_clk.autoblock = 1; /* Autoblock clk while changing clksrc */
mii_ext_tx_clk.pd = 0; /* Power Down off => enabled */
sja1105_cgu_mii_control_packing(packed_buf, &mii_ext_tx_clk, PACK);
return sja1105_xfer_buf(priv, SPI_WRITE, regs->mii_ext_tx_clk[port],
packed_buf, SJA1105_SIZE_CGU_CMD);
}
static int
sja1105_cgu_mii_ext_rx_clk_config(struct sja1105_private *priv, int port)
{
const struct sja1105_regs *regs = priv->info->regs;
struct sja1105_cgu_mii_ctrl mii_ext_rx_clk;
u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0};
const int clk_sources[] = {
CLKSRC_IDIV0,
CLKSRC_IDIV1,
CLKSRC_IDIV2,
CLKSRC_IDIV3,
CLKSRC_IDIV4,
};
if (regs->mii_ext_rx_clk[port] == SJA1105_RSV_ADDR)
return 0;
/* Payload for packed_buf */
mii_ext_rx_clk.clksrc = clk_sources[port];
mii_ext_rx_clk.autoblock = 1; /* Autoblock clk while changing clksrc */
mii_ext_rx_clk.pd = 0; /* Power Down off => enabled */
sja1105_cgu_mii_control_packing(packed_buf, &mii_ext_rx_clk, PACK);
return sja1105_xfer_buf(priv, SPI_WRITE, regs->mii_ext_rx_clk[port],
packed_buf, SJA1105_SIZE_CGU_CMD);
}
static int sja1105_mii_clocking_setup(struct sja1105_private *priv, int port,
sja1105_mii_role_t role)
{
struct device *dev = priv->ds->dev;
int rc;
dev_dbg(dev, "Configuring MII-%s clocking\n",
(role == XMII_MAC) ? "MAC" : "PHY");
/* If role is MAC, disable IDIV
* If role is PHY, enable IDIV and configure for 1/1 divider
*/
rc = sja1105_cgu_idiv_config(priv, port, (role == XMII_PHY), 1);
if (rc < 0)
return rc;
/* Configure CLKSRC of MII_TX_CLK_n
* * If role is MAC, select TX_CLK_n
* * If role is PHY, select IDIV_n
*/
rc = sja1105_cgu_mii_tx_clk_config(priv, port, role);
if (rc < 0)
return rc;
/* Configure CLKSRC of MII_RX_CLK_n
* Select RX_CLK_n
*/
rc = sja1105_cgu_mii_rx_clk_config(priv, port);
if (rc < 0)
return rc;
if (role == XMII_PHY) {
/* Per MII spec, the PHY (which is us) drives the TX_CLK pin */
/* Configure CLKSRC of EXT_TX_CLK_n
* Select IDIV_n
*/
rc = sja1105_cgu_mii_ext_tx_clk_config(priv, port);
if (rc < 0)
return rc;
/* Configure CLKSRC of EXT_RX_CLK_n
* Select IDIV_n
*/
rc = sja1105_cgu_mii_ext_rx_clk_config(priv, port);
if (rc < 0)
return rc;
}
return 0;
}
static void
sja1105_cgu_pll_control_packing(void *buf, struct sja1105_cgu_pll_ctrl *cmd,
enum packing_op op)
{
const int size = 4;
sja1105_packing(buf, &cmd->pllclksrc, 28, 24, size, op);
sja1105_packing(buf, &cmd->msel, 23, 16, size, op);
sja1105_packing(buf, &cmd->autoblock, 11, 11, size, op);
sja1105_packing(buf, &cmd->psel, 9, 8, size, op);
sja1105_packing(buf, &cmd->direct, 7, 7, size, op);
sja1105_packing(buf, &cmd->fbsel, 6, 6, size, op);
sja1105_packing(buf, &cmd->bypass, 1, 1, size, op);
sja1105_packing(buf, &cmd->pd, 0, 0, size, op);
}
static int sja1105_cgu_rgmii_tx_clk_config(struct sja1105_private *priv,
int port, u64 speed)
{
const struct sja1105_regs *regs = priv->info->regs;
struct sja1105_cgu_mii_ctrl txc;
u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0};
int clksrc;
if (regs->rgmii_tx_clk[port] == SJA1105_RSV_ADDR)
return 0;
if (speed == priv->info->port_speed[SJA1105_SPEED_1000MBPS]) {
clksrc = CLKSRC_PLL0;
} else {
int clk_sources[] = {CLKSRC_IDIV0, CLKSRC_IDIV1, CLKSRC_IDIV2,
CLKSRC_IDIV3, CLKSRC_IDIV4};
clksrc = clk_sources[port];
}
/* RGMII: 125MHz for 1000, 25MHz for 100, 2.5MHz for 10 */
txc.clksrc = clksrc;
/* Autoblock clk while changing clksrc */
txc.autoblock = 1;
/* Power Down off => enabled */
txc.pd = 0;
sja1105_cgu_mii_control_packing(packed_buf, &txc, PACK);
return sja1105_xfer_buf(priv, SPI_WRITE, regs->rgmii_tx_clk[port],
packed_buf, SJA1105_SIZE_CGU_CMD);
}
/* AGU */
static void
sja1105_cfg_pad_mii_packing(void *buf, struct sja1105_cfg_pad_mii *cmd,
enum packing_op op)
{
const int size = 4;
sja1105_packing(buf, &cmd->d32_os, 28, 27, size, op);
sja1105_packing(buf, &cmd->d32_ih, 26, 26, size, op);
sja1105_packing(buf, &cmd->d32_ipud, 25, 24, size, op);
sja1105_packing(buf, &cmd->d10_os, 20, 19, size, op);
sja1105_packing(buf, &cmd->d10_ih, 18, 18, size, op);
sja1105_packing(buf, &cmd->d10_ipud, 17, 16, size, op);
sja1105_packing(buf, &cmd->ctrl_os, 12, 11, size, op);
sja1105_packing(buf, &cmd->ctrl_ih, 10, 10, size, op);
sja1105_packing(buf, &cmd->ctrl_ipud, 9, 8, size, op);
sja1105_packing(buf, &cmd->clk_os, 4, 3, size, op);
sja1105_packing(buf, &cmd->clk_ih, 2, 2, size, op);
sja1105_packing(buf, &cmd->clk_ipud, 1, 0, size, op);
}
static int sja1105_rgmii_cfg_pad_tx_config(struct sja1105_private *priv,
int port)
{
const struct sja1105_regs *regs = priv->info->regs;
struct sja1105_cfg_pad_mii pad_mii_tx = {0};
u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0};
if (regs->pad_mii_tx[port] == SJA1105_RSV_ADDR)
return 0;
/* Payload */
pad_mii_tx.d32_os = 3; /* TXD[3:2] output stage: */
/* high noise/high speed */
pad_mii_tx.d10_os = 3; /* TXD[1:0] output stage: */
/* high noise/high speed */
pad_mii_tx.d32_ipud = 2; /* TXD[3:2] input stage: */
/* plain input (default) */
pad_mii_tx.d10_ipud = 2; /* TXD[1:0] input stage: */
/* plain input (default) */
pad_mii_tx.ctrl_os = 3; /* TX_CTL / TX_ER output stage */
pad_mii_tx.ctrl_ipud = 2; /* TX_CTL / TX_ER input stage (default) */
pad_mii_tx.clk_os = 3; /* TX_CLK output stage */
pad_mii_tx.clk_ih = 0; /* TX_CLK input hysteresis (default) */
pad_mii_tx.clk_ipud = 2; /* TX_CLK input stage (default) */
sja1105_cfg_pad_mii_packing(packed_buf, &pad_mii_tx, PACK);
return sja1105_xfer_buf(priv, SPI_WRITE, regs->pad_mii_tx[port],
packed_buf, SJA1105_SIZE_CGU_CMD);
}
static int sja1105_cfg_pad_rx_config(struct sja1105_private *priv, int port)
{
const struct sja1105_regs *regs = priv->info->regs;
struct sja1105_cfg_pad_mii pad_mii_rx = {0};
u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0};
if (regs->pad_mii_rx[port] == SJA1105_RSV_ADDR)
return 0;
/* Payload */
pad_mii_rx.d32_ih = 0; /* RXD[3:2] input stage hysteresis: */
/* non-Schmitt (default) */
pad_mii_rx.d32_ipud = 2; /* RXD[3:2] input weak pull-up/down */
/* plain input (default) */
pad_mii_rx.d10_ih = 0; /* RXD[1:0] input stage hysteresis: */
/* non-Schmitt (default) */
pad_mii_rx.d10_ipud = 2; /* RXD[1:0] input weak pull-up/down */
/* plain input (default) */
pad_mii_rx.ctrl_ih = 0; /* RX_DV/CRS_DV/RX_CTL and RX_ER */
/* input stage hysteresis: */
/* non-Schmitt (default) */
pad_mii_rx.ctrl_ipud = 3; /* RX_DV/CRS_DV/RX_CTL and RX_ER */
/* input stage weak pull-up/down: */
/* pull-down */
pad_mii_rx.clk_os = 2; /* RX_CLK/RXC output stage: */
/* medium noise/fast speed (default) */
pad_mii_rx.clk_ih = 0; /* RX_CLK/RXC input hysteresis: */
/* non-Schmitt (default) */
pad_mii_rx.clk_ipud = 2; /* RX_CLK/RXC input pull-up/down: */
/* plain input (default) */
sja1105_cfg_pad_mii_packing(packed_buf, &pad_mii_rx, PACK);
return sja1105_xfer_buf(priv, SPI_WRITE, regs->pad_mii_rx[port],
packed_buf, SJA1105_SIZE_CGU_CMD);
}
static void
sja1105_cfg_pad_mii_id_packing(void *buf, struct sja1105_cfg_pad_mii_id *cmd,
enum packing_op op)
{
const int size = SJA1105_SIZE_CGU_CMD;
sja1105_packing(buf, &cmd->rxc_stable_ovr, 15, 15, size, op);
sja1105_packing(buf, &cmd->rxc_delay, 14, 10, size, op);
sja1105_packing(buf, &cmd->rxc_bypass, 9, 9, size, op);
sja1105_packing(buf, &cmd->rxc_pd, 8, 8, size, op);
sja1105_packing(buf, &cmd->txc_stable_ovr, 7, 7, size, op);
sja1105_packing(buf, &cmd->txc_delay, 6, 2, size, op);
sja1105_packing(buf, &cmd->txc_bypass, 1, 1, size, op);
sja1105_packing(buf, &cmd->txc_pd, 0, 0, size, op);
}
static void
sja1110_cfg_pad_mii_id_packing(void *buf, struct sja1105_cfg_pad_mii_id *cmd,
enum packing_op op)
{
const int size = SJA1105_SIZE_CGU_CMD;
u64 range = 4;
/* Fields RXC_RANGE and TXC_RANGE select the input frequency range:
* 0 = 2.5MHz
* 1 = 25MHz
* 2 = 50MHz
* 3 = 125MHz
* 4 = Automatically determined by port speed.
* There's no point in defining a structure different than the one for
* SJA1105, so just hardcode the frequency range to automatic, just as
* before.
*/
sja1105_packing(buf, &cmd->rxc_stable_ovr, 26, 26, size, op);
sja1105_packing(buf, &cmd->rxc_delay, 25, 21, size, op);
sja1105_packing(buf, &range, 20, 18, size, op);
sja1105_packing(buf, &cmd->rxc_bypass, 17, 17, size, op);
sja1105_packing(buf, &cmd->rxc_pd, 16, 16, size, op);
sja1105_packing(buf, &cmd->txc_stable_ovr, 10, 10, size, op);
sja1105_packing(buf, &cmd->txc_delay, 9, 5, size, op);
sja1105_packing(buf, &range, 4, 2, size, op);
sja1105_packing(buf, &cmd->txc_bypass, 1, 1, size, op);
sja1105_packing(buf, &cmd->txc_pd, 0, 0, size, op);
}
/* Valid range in degrees is an integer between 73.8 and 101.7 */
static u64 sja1105_rgmii_delay(u64 phase)
{
/* UM11040.pdf: The delay in degree phase is 73.8 + delay_tune * 0.9.
* To avoid floating point operations we'll multiply by 10
* and get 1 decimal point precision.
*/
phase *= 10;
return (phase - 738) / 9;
}
/* The RGMII delay setup procedure is 2-step and gets called upon each
* .phylink_mac_config. Both are strategic.
* The reason is that the RX Tunable Delay Line of the SJA1105 MAC has issues
* with recovering from a frequency change of the link partner's RGMII clock.
* The easiest way to recover from this is to temporarily power down the TDL,
* as it will re-lock at the new frequency afterwards.
*/
int sja1105pqrs_setup_rgmii_delay(const void *ctx, int port)
{
const struct sja1105_private *priv = ctx;
const struct sja1105_regs *regs = priv->info->regs;
struct sja1105_cfg_pad_mii_id pad_mii_id = {0};
u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0};
int rc;
if (priv->rgmii_rx_delay[port])
pad_mii_id.rxc_delay = sja1105_rgmii_delay(90);
if (priv->rgmii_tx_delay[port])
pad_mii_id.txc_delay = sja1105_rgmii_delay(90);
/* Stage 1: Turn the RGMII delay lines off. */
pad_mii_id.rxc_bypass = 1;
pad_mii_id.rxc_pd = 1;
pad_mii_id.txc_bypass = 1;
pad_mii_id.txc_pd = 1;
sja1105_cfg_pad_mii_id_packing(packed_buf, &pad_mii_id, PACK);
rc = sja1105_xfer_buf(priv, SPI_WRITE, regs->pad_mii_id[port],
packed_buf, SJA1105_SIZE_CGU_CMD);
if (rc < 0)
return rc;
/* Stage 2: Turn the RGMII delay lines on. */
if (priv->rgmii_rx_delay[port]) {
pad_mii_id.rxc_bypass = 0;
pad_mii_id.rxc_pd = 0;
}
if (priv->rgmii_tx_delay[port]) {
pad_mii_id.txc_bypass = 0;
pad_mii_id.txc_pd = 0;
}
sja1105_cfg_pad_mii_id_packing(packed_buf, &pad_mii_id, PACK);
return sja1105_xfer_buf(priv, SPI_WRITE, regs->pad_mii_id[port],
packed_buf, SJA1105_SIZE_CGU_CMD);
}
int sja1110_setup_rgmii_delay(const void *ctx, int port)
{
const struct sja1105_private *priv = ctx;
const struct sja1105_regs *regs = priv->info->regs;
struct sja1105_cfg_pad_mii_id pad_mii_id = {0};
u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0};
pad_mii_id.rxc_pd = 1;
pad_mii_id.txc_pd = 1;
if (priv->rgmii_rx_delay[port]) {
pad_mii_id.rxc_delay = sja1105_rgmii_delay(90);
/* The "BYPASS" bit in SJA1110 is actually a "don't bypass" */
pad_mii_id.rxc_bypass = 1;
pad_mii_id.rxc_pd = 0;
}
if (priv->rgmii_tx_delay[port]) {
pad_mii_id.txc_delay = sja1105_rgmii_delay(90);
pad_mii_id.txc_bypass = 1;
pad_mii_id.txc_pd = 0;
}
sja1110_cfg_pad_mii_id_packing(packed_buf, &pad_mii_id, PACK);
return sja1105_xfer_buf(priv, SPI_WRITE, regs->pad_mii_id[port],
packed_buf, SJA1105_SIZE_CGU_CMD);
}
static int sja1105_rgmii_clocking_setup(struct sja1105_private *priv, int port,
sja1105_mii_role_t role)
{
struct device *dev = priv->ds->dev;
struct sja1105_mac_config_entry *mac;
u64 speed;
int rc;
mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries;
speed = mac[port].speed;
dev_dbg(dev, "Configuring port %d RGMII at speed %lldMbps\n",
port, speed);
if (speed == priv->info->port_speed[SJA1105_SPEED_1000MBPS]) {
/* 1000Mbps, IDIV disabled (125 MHz) */
rc = sja1105_cgu_idiv_config(priv, port, false, 1);
} else if (speed == priv->info->port_speed[SJA1105_SPEED_100MBPS]) {
/* 100Mbps, IDIV enabled, divide by 1 (25 MHz) */
rc = sja1105_cgu_idiv_config(priv, port, true, 1);
} else if (speed == priv->info->port_speed[SJA1105_SPEED_10MBPS]) {
/* 10Mbps, IDIV enabled, divide by 10 (2.5 MHz) */
rc = sja1105_cgu_idiv_config(priv, port, true, 10);
} else if (speed == priv->info->port_speed[SJA1105_SPEED_AUTO]) {
/* Skip CGU configuration if there is no speed available
* (e.g. link is not established yet)
*/
dev_dbg(dev, "Speed not available, skipping CGU config\n");
return 0;
} else {
rc = -EINVAL;
}
if (rc < 0) {
dev_err(dev, "Failed to configure idiv\n");
return rc;
}
rc = sja1105_cgu_rgmii_tx_clk_config(priv, port, speed);
if (rc < 0) {
dev_err(dev, "Failed to configure RGMII Tx clock\n");
return rc;
}
rc = sja1105_rgmii_cfg_pad_tx_config(priv, port);
if (rc < 0) {
dev_err(dev, "Failed to configure Tx pad registers\n");
return rc;
}
if (!priv->info->setup_rgmii_delay)
return 0;
return priv->info->setup_rgmii_delay(priv, port);
}
static int sja1105_cgu_rmii_ref_clk_config(struct sja1105_private *priv,
int port)
{
const struct sja1105_regs *regs = priv->info->regs;
struct sja1105_cgu_mii_ctrl ref_clk;
u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0};
const int clk_sources[] = {
CLKSRC_MII0_TX_CLK,
CLKSRC_MII1_TX_CLK,
CLKSRC_MII2_TX_CLK,
CLKSRC_MII3_TX_CLK,
CLKSRC_MII4_TX_CLK,
};
if (regs->rmii_ref_clk[port] == SJA1105_RSV_ADDR)
return 0;
/* Payload for packed_buf */
ref_clk.clksrc = clk_sources[port];
ref_clk.autoblock = 1; /* Autoblock clk while changing clksrc */
ref_clk.pd = 0; /* Power Down off => enabled */
sja1105_cgu_mii_control_packing(packed_buf, &ref_clk, PACK);
return sja1105_xfer_buf(priv, SPI_WRITE, regs->rmii_ref_clk[port],
packed_buf, SJA1105_SIZE_CGU_CMD);
}
static int
sja1105_cgu_rmii_ext_tx_clk_config(struct sja1105_private *priv, int port)
{
const struct sja1105_regs *regs = priv->info->regs;
struct sja1105_cgu_mii_ctrl ext_tx_clk;
u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0};
if (regs->rmii_ext_tx_clk[port] == SJA1105_RSV_ADDR)
return 0;
/* Payload for packed_buf */
ext_tx_clk.clksrc = CLKSRC_PLL1;
ext_tx_clk.autoblock = 1; /* Autoblock clk while changing clksrc */
ext_tx_clk.pd = 0; /* Power Down off => enabled */
sja1105_cgu_mii_control_packing(packed_buf, &ext_tx_clk, PACK);
return sja1105_xfer_buf(priv, SPI_WRITE, regs->rmii_ext_tx_clk[port],
packed_buf, SJA1105_SIZE_CGU_CMD);
}
static int sja1105_cgu_rmii_pll_config(struct sja1105_private *priv)
{
const struct sja1105_regs *regs = priv->info->regs;
u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0};
struct sja1105_cgu_pll_ctrl pll = {0};
struct device *dev = priv->ds->dev;
int rc;
if (regs->rmii_pll1 == SJA1105_RSV_ADDR)
return 0;
/* PLL1 must be enabled and output 50 Mhz.
* This is done by writing first 0x0A010941 to
* the PLL_1_C register and then deasserting
* power down (PD) 0x0A010940.
*/
/* Step 1: PLL1 setup for 50Mhz */
pll.pllclksrc = 0xA;
pll.msel = 0x1;
pll.autoblock = 0x1;
pll.psel = 0x1;
pll.direct = 0x0;
pll.fbsel = 0x1;
pll.bypass = 0x0;
pll.pd = 0x1;
sja1105_cgu_pll_control_packing(packed_buf, &pll, PACK);
rc = sja1105_xfer_buf(priv, SPI_WRITE, regs->rmii_pll1, packed_buf,
SJA1105_SIZE_CGU_CMD);
if (rc < 0) {
dev_err(dev, "failed to configure PLL1 for 50MHz\n");
return rc;
}
/* Step 2: Enable PLL1 */
pll.pd = 0x0;
sja1105_cgu_pll_control_packing(packed_buf, &pll, PACK);
rc = sja1105_xfer_buf(priv, SPI_WRITE, regs->rmii_pll1, packed_buf,
SJA1105_SIZE_CGU_CMD);
if (rc < 0) {
dev_err(dev, "failed to enable PLL1\n");
return rc;
}
return rc;
}
static int sja1105_rmii_clocking_setup(struct sja1105_private *priv, int port,
sja1105_mii_role_t role)
{
struct device *dev = priv->ds->dev;
int rc;
dev_dbg(dev, "Configuring RMII-%s clocking\n",
(role == XMII_MAC) ? "MAC" : "PHY");
/* AH1601.pdf chapter 2.5.1. Sources */
if (role == XMII_MAC) {
/* Configure and enable PLL1 for 50Mhz output */
rc = sja1105_cgu_rmii_pll_config(priv);
if (rc < 0)
return rc;
}
/* Disable IDIV for this port */
rc = sja1105_cgu_idiv_config(priv, port, false, 1);
if (rc < 0)
return rc;
/* Source to sink mappings */
rc = sja1105_cgu_rmii_ref_clk_config(priv, port);
if (rc < 0)
return rc;
if (role == XMII_MAC) {
rc = sja1105_cgu_rmii_ext_tx_clk_config(priv, port);
if (rc < 0)
return rc;
}
return 0;
}
int sja1105_clocking_setup_port(struct sja1105_private *priv, int port)
{
struct sja1105_xmii_params_entry *mii;
struct device *dev = priv->ds->dev;
sja1105_phy_interface_t phy_mode;
sja1105_mii_role_t role;
int rc;
mii = priv->static_config.tables[BLK_IDX_XMII_PARAMS].entries;
/* RGMII etc */
phy_mode = mii->xmii_mode[port];
/* MAC or PHY, for applicable types (not RGMII) */
role = mii->phy_mac[port];
switch (phy_mode) {
case XMII_MODE_MII:
rc = sja1105_mii_clocking_setup(priv, port, role);
break;
case XMII_MODE_RMII:
rc = sja1105_rmii_clocking_setup(priv, port, role);
break;
case XMII_MODE_RGMII:
rc = sja1105_rgmii_clocking_setup(priv, port, role);
break;
case XMII_MODE_SGMII:
/* Nothing to do in the CGU for SGMII */
rc = 0;
break;
default:
dev_err(dev, "Invalid interface mode specified: %d\n",
phy_mode);
return -EINVAL;
}
if (rc) {
dev_err(dev, "Clocking setup for port %d failed: %d\n",
port, rc);
return rc;
}
/* Internally pull down the RX_DV/CRS_DV/RX_CTL and RX_ER inputs */
return sja1105_cfg_pad_rx_config(priv, port);
}
int sja1105_clocking_setup(struct sja1105_private *priv)
{
struct dsa_switch *ds = priv->ds;
int port, rc;
for (port = 0; port < ds->num_ports; port++) {
rc = sja1105_clocking_setup_port(priv, port);
if (rc < 0)
return rc;
}
return 0;
}
static void
sja1110_cgu_outclk_packing(void *buf, struct sja1110_cgu_outclk *outclk,
enum packing_op op)
{
const int size = 4;
sja1105_packing(buf, &outclk->clksrc, 27, 24, size, op);
sja1105_packing(buf, &outclk->autoblock, 11, 11, size, op);
sja1105_packing(buf, &outclk->pd, 0, 0, size, op);
}
int sja1110_disable_microcontroller(struct sja1105_private *priv)
{
u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0};
struct sja1110_cgu_outclk outclk_6_c = {
.clksrc = 0x3,
.pd = true,
};
struct sja1110_cgu_outclk outclk_7_c = {
.clksrc = 0x5,
.pd = true,
};
int rc;
/* Power down the BASE_TIMER_CLK to disable the watchdog timer */
sja1110_cgu_outclk_packing(packed_buf, &outclk_7_c, PACK);
rc = sja1105_xfer_buf(priv, SPI_WRITE, SJA1110_BASE_TIMER_CLK,
packed_buf, SJA1105_SIZE_CGU_CMD);
if (rc)
return rc;
/* Power down the BASE_MCSS_CLOCK to gate the microcontroller off */
sja1110_cgu_outclk_packing(packed_buf, &outclk_6_c, PACK);
return sja1105_xfer_buf(priv, SPI_WRITE, SJA1110_BASE_MCSS_CLK,
packed_buf, SJA1105_SIZE_CGU_CMD);
}
Reference in New Issue View Git Blame Copy Permalink