IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Before commit d4289fcc9b ("net: IP6 defrag: use rbtrees for IPv6
defrag"), a netperf UDP_STREAM test[0] using big IPv6 datagrams (thus
generating many fragments) and running over an IPsec tunnel, reported
more than 6Gbps throughput. After that patch, the same test gets only
9Mbps when receiving on a be2net nic (driver can make a big difference
here, for example, ixgbe doesn't seem to be affected).
By reusing the IPv4 defragmentation code, IPv6 lost fragment coalescing
(IPv4 fragment coalescing was dropped by commit 14fe22e334 ("Revert
"ipv4: use skb coalescing in defragmentation"")).
Without fragment coalescing, be2net runs out of Rx ring entries and
starts to drop frames (ethtool reports rx_drops_no_frags errors). Since
the netperf traffic is only composed of UDP fragments, any lost packet
prevents reassembly of the full datagram. Therefore, fragments which
have no possibility to ever get reassembled pile up in the reassembly
queue, until the memory accounting exeeds the threshold. At that point
no fragment is accepted anymore, which effectively discards all
netperf traffic.
When reassembly timeout expires, some stale fragments are removed from
the reassembly queue, so a few packets can be received, reassembled
and delivered to the netperf receiver. But the nic still drops frames
and soon the reassembly queue gets filled again with stale fragments.
These long time frames where no datagram can be received explain why
the performance drop is so significant.
Re-introducing fragment coalescing is enough to get the initial
performances again (6.6Gbps with be2net): driver doesn't drop frames
anymore (no more rx_drops_no_frags errors) and the reassembly engine
works at full speed.
This patch is quite conservative and only coalesces skbs for local
IPv4 and IPv6 delivery (in order to avoid changing skb geometry when
forwarding). Coalescing could be extended in the future if need be, as
more scenarios would probably benefit from it.
[0]: Test configuration
Sender:
ip xfrm policy flush
ip xfrm state flush
ip xfrm state add src fc00:1::1 dst fc00:2::1 proto esp spi 0x1000 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:1::1 dst fc00:2::1
ip xfrm policy add src fc00:1::1 dst fc00:2::1 dir in tmpl src fc00:1::1 dst fc00:2::1 proto esp mode transport action allow
ip xfrm state add src fc00:2::1 dst fc00:1::1 proto esp spi 0x1001 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:2::1 dst fc00:1::1
ip xfrm policy add src fc00:2::1 dst fc00:1::1 dir out tmpl src fc00:2::1 dst fc00:1::1 proto esp mode transport action allow
netserver -D -L fc00:2::1
Receiver:
ip xfrm policy flush
ip xfrm state flush
ip xfrm state add src fc00:2::1 dst fc00:1::1 proto esp spi 0x1001 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:2::1 dst fc00:1::1
ip xfrm policy add src fc00:2::1 dst fc00:1::1 dir in tmpl src fc00:2::1 dst fc00:1::1 proto esp mode transport action allow
ip xfrm state add src fc00:1::1 dst fc00:2::1 proto esp spi 0x1000 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:1::1 dst fc00:2::1
ip xfrm policy add src fc00:1::1 dst fc00:2::1 dir out tmpl src fc00:1::1 dst fc00:2::1 proto esp mode transport action allow
netperf -H fc00:2::1 -f k -P 0 -L fc00:1::1 -l 60 -t UDP_STREAM -I 99,5 -i 5,5 -T5,5 -6
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
891584f48a