689ca16e52
This adds a driver based on serdev driver for the NXP BT serial protocol based on running H:4, which can enable the built-in Bluetooth device inside an NXP BT chip. This driver has Power Save feature that will put the chip into sleep state whenever there is no activity for 2000ms, and will be woken up when any activity is to be initiated over UART. This driver enables the power save feature by default by sending the vendor specific commands to the chip during setup. During setup, the driver checks if a FW is already running on the chip by waiting for the bootloader signature, and downloads device specific FW file into the chip over UART if bootloader signature is received.. Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
54 lines
1.7 KiB
Makefile
54 lines
1.7 KiB
Makefile
# SPDX-License-Identifier: GPL-2.0
|
|
#
|
|
# Makefile for the Linux Bluetooth HCI device drivers.
|
|
#
|
|
|
|
obj-$(CONFIG_BT_HCIVHCI) += hci_vhci.o
|
|
obj-$(CONFIG_BT_HCIUART) += hci_uart.o
|
|
obj-$(CONFIG_BT_HCIBCM203X) += bcm203x.o
|
|
obj-$(CONFIG_BT_HCIBCM4377) += hci_bcm4377.o
|
|
obj-$(CONFIG_BT_HCIBPA10X) += bpa10x.o
|
|
obj-$(CONFIG_BT_HCIBFUSB) += bfusb.o
|
|
obj-$(CONFIG_BT_HCIDTL1) += dtl1_cs.o
|
|
obj-$(CONFIG_BT_HCIBT3C) += bt3c_cs.o
|
|
obj-$(CONFIG_BT_HCIBLUECARD) += bluecard_cs.o
|
|
|
|
obj-$(CONFIG_BT_HCIBTUSB) += btusb.o
|
|
obj-$(CONFIG_BT_HCIBTSDIO) += btsdio.o
|
|
|
|
obj-$(CONFIG_BT_INTEL) += btintel.o
|
|
obj-$(CONFIG_BT_ATH3K) += ath3k.o
|
|
obj-$(CONFIG_BT_MRVL) += btmrvl.o
|
|
obj-$(CONFIG_BT_MRVL_SDIO) += btmrvl_sdio.o
|
|
obj-$(CONFIG_BT_MTKSDIO) += btmtksdio.o
|
|
obj-$(CONFIG_BT_MTKUART) += btmtkuart.o
|
|
obj-$(CONFIG_BT_QCOMSMD) += btqcomsmd.o
|
|
obj-$(CONFIG_BT_BCM) += btbcm.o
|
|
obj-$(CONFIG_BT_RTL) += btrtl.o
|
|
obj-$(CONFIG_BT_QCA) += btqca.o
|
|
obj-$(CONFIG_BT_MTK) += btmtk.o
|
|
|
|
obj-$(CONFIG_BT_VIRTIO) += virtio_bt.o
|
|
obj-$(CONFIG_BT_NXPUART) += btnxpuart.o
|
|
|
|
obj-$(CONFIG_BT_HCIUART_NOKIA) += hci_nokia.o
|
|
|
|
obj-$(CONFIG_BT_HCIRSI) += btrsi.o
|
|
|
|
btmrvl-y := btmrvl_main.o
|
|
btmrvl-$(CONFIG_DEBUG_FS) += btmrvl_debugfs.o
|
|
|
|
hci_uart-y := hci_ldisc.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_SERDEV) += hci_serdev.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_H4) += hci_h4.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_BCSP) += hci_bcsp.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_LL) += hci_ll.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_ATH3K) += hci_ath.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_3WIRE) += hci_h5.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_INTEL) += hci_intel.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_BCM) += hci_bcm.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_QCA) += hci_qca.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_AG6XX) += hci_ag6xx.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_MRVL) += hci_mrvl.o
|
|
hci_uart-objs := $(hci_uart-y)
|