8b1750de6a
PHYs have an address on the mdio bus. So the unit name should contain an address. This is complicated in that some .dtsi files contain the node, but the reg is set in the .dts file. In this case, use the abstract address X. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
108 lines
1.8 KiB
Plaintext
108 lines
1.8 KiB
Plaintext
/ {
|
|
model = "QNAP TS219 family";
|
|
compatible = "qnap,ts219", "marvell,kirkwood";
|
|
|
|
memory {
|
|
device_type = "memory";
|
|
reg = <0x00000000 0x20000000>;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8";
|
|
stdout-path = &uart0;
|
|
};
|
|
|
|
mbus {
|
|
pcie-controller {
|
|
status = "okay";
|
|
|
|
pcie@1,0 {
|
|
status = "okay";
|
|
};
|
|
};
|
|
};
|
|
|
|
ocp@f1000000 {
|
|
i2c@11000 {
|
|
status = "okay";
|
|
clock-frequency = <400000>;
|
|
|
|
s35390a: s35390a@30 {
|
|
compatible = "s35390a";
|
|
reg = <0x30>;
|
|
};
|
|
};
|
|
serial@12000 {
|
|
status = "okay";
|
|
};
|
|
serial@12100 {
|
|
status = "okay";
|
|
};
|
|
poweroff@12100 {
|
|
compatible = "qnap,power-off";
|
|
reg = <0x12100 0x100>;
|
|
clocks = <&gate_clk 7>;
|
|
};
|
|
spi@10600 {
|
|
status = "okay";
|
|
|
|
m25p128@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "m25p128", "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <20000000>;
|
|
mode = <0>;
|
|
|
|
partition@0000000 {
|
|
reg = <0x00000000 0x00080000>;
|
|
label = "U-Boot";
|
|
};
|
|
|
|
partition@00200000 {
|
|
reg = <0x00200000 0x00200000>;
|
|
label = "Kernel";
|
|
};
|
|
|
|
partition@00400000 {
|
|
reg = <0x00400000 0x00900000>;
|
|
label = "RootFS1";
|
|
};
|
|
partition@00d00000 {
|
|
reg = <0x00d00000 0x00300000>;
|
|
label = "RootFS2";
|
|
};
|
|
partition@00040000 {
|
|
reg = <0x00080000 0x00040000>;
|
|
label = "U-Boot Config";
|
|
};
|
|
partition@000c0000 {
|
|
reg = <0x000c0000 0x00140000>;
|
|
label = "NAS Config";
|
|
};
|
|
};
|
|
};
|
|
sata@80000 {
|
|
pinctrl-0 = <&pmx_sata0 &pmx_sata1>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
nr-ports = <2>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&mdio {
|
|
status = "okay";
|
|
|
|
ethphy0: ethernet-phy@X {
|
|
/* overwrite reg property in board file */
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
ethernet0-port@0 {
|
|
phy-handle = <ðphy0>;
|
|
};
|
|
};
|