iv/linux
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
linux/drivers/net/ethernet/Kconfig
Alexandru Tachici bc93e19d08 net: ethernet: adi: Add ADIN1110 support 
The ADIN1110 is a low power single port 10BASE-T1L MAC-PHY
designed for industrial Ethernet applications. It integrates
an Ethernet PHY core with a MAC and all the associated analog
circuitry, input and output clock buffering.

ADIN1110 MAC-PHY encapsulates the ADIN1100 PHY. The PHY registers
can be accessed through the MDIO MAC registers.
We are registering an MDIO bus with custom read/write in order
to let the PHY to be discovered by the PAL. This will let
the ADIN1100 Linux driver to probe and take control of
the PHY.

The ADIN2111 is a low power, low complexity, two-Ethernet ports
switch with integrated 10BASE-T1L PHYs and one serial peripheral
interface (SPI) port.

The device is designed for industrial Ethernet applications using
low power constrained nodes and is compliant with the IEEE 802.3cg-2019
Ethernet standard for long reach 10 Mbps single pair Ethernet (SPE).
The switch supports various routing configurations between
the two Ethernet ports and the SPI host port providing a flexible
solution for line, daisy-chain, or ring network topologies.

The ADIN2111 supports cable reach of up to 1700 meters with ultra
low power consumption of 77 mW. The two PHY cores support the
1.0 V p-p operating mode and the 2.4 V p-p operating mode defined
in the IEEE 802.3cg standard.

The device integrates the switch, two Ethernet physical layer (PHY)
cores with a media access control (MAC) interface and all the
associated analog circuitry, and input and output clock buffering.

The device also includes internal buffer queues, the SPI and
subsystem registers, as well as the control logic to manage the reset
and clock control and hardware pin configuration.

Access to the PHYs is exposed via an internal MDIO bus. Writes/reads
can be performed by reading/writing to the ADIN2111 MDIO registers
via SPI.

On probe, for each port, a struct net_device is allocated and
registered. When both ports are added to the same bridge, the driver
will enable offloading of frame forwarding at the hardware level.

Driver offers STP support. Normal operation on forwarding state.
Allows only frames with the 802.1d DA to be passed to the host
when in any of the other states.

When both ports of ADIN2111 belong to the same SW bridge a maximum
of 12 FDB entries will offloaded by the hardware and are marked as such.

Co-developed-by: Lennart Franzen <lennart@lfdomain.com>
Signed-off-by: Lennart Franzen <lennart@lfdomain.com>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-09-20 15:00:30 +02:00

197 lines
6.4 KiB
Plaintext
Raw Blame History

# SPDX-License-Identifier: GPL-2.0-only
#
# Ethernet LAN device configuration
#
menuconfig ETHERNET
bool "Ethernet driver support"
depends on NET
default y
help
This section contains all the Ethernet device drivers.
if ETHERNET
config MDIO
tristate
config SUNGEM_PHY
tristate
source "drivers/net/ethernet/3com/Kconfig"
source "drivers/net/ethernet/actions/Kconfig"
source "drivers/net/ethernet/adaptec/Kconfig"
source "drivers/net/ethernet/aeroflex/Kconfig"
source "drivers/net/ethernet/agere/Kconfig"
source "drivers/net/ethernet/alacritech/Kconfig"
source "drivers/net/ethernet/allwinner/Kconfig"
source "drivers/net/ethernet/alteon/Kconfig"
source "drivers/net/ethernet/altera/Kconfig"
source "drivers/net/ethernet/amazon/Kconfig"
source "drivers/net/ethernet/amd/Kconfig"
source "drivers/net/ethernet/apm/Kconfig"
source "drivers/net/ethernet/apple/Kconfig"
source "drivers/net/ethernet/aquantia/Kconfig"
source "drivers/net/ethernet/arc/Kconfig"
source "drivers/net/ethernet/asix/Kconfig"
source "drivers/net/ethernet/atheros/Kconfig"
config CX_ECAT
tristate "Beckhoff CX5020 EtherCAT master support"
depends on PCI
depends on X86 || COMPILE_TEST
help
Driver for EtherCAT master module located on CCAT FPGA
that can be found on Beckhoff CX5020, and possibly other of CX
Beckhoff CX series industrial PCs.
To compile this driver as a module, choose M here. The module
will be called ec_bhf.
source "drivers/net/ethernet/broadcom/Kconfig"
source "drivers/net/ethernet/cadence/Kconfig"
source "drivers/net/ethernet/calxeda/Kconfig"
source "drivers/net/ethernet/cavium/Kconfig"
source "drivers/net/ethernet/chelsio/Kconfig"
source "drivers/net/ethernet/cirrus/Kconfig"
source "drivers/net/ethernet/cisco/Kconfig"
source "drivers/net/ethernet/cortina/Kconfig"
source "drivers/net/ethernet/davicom/Kconfig"
config DNET
tristate "Dave ethernet support (DNET)"
depends on HAS_IOMEM
select PHYLIB
help
The Dave ethernet interface (DNET) is found on Qong Board FPGA.
Say Y to include support for the DNET chip.
To compile this driver as a module, choose M here: the module
will be called dnet.
source "drivers/net/ethernet/dec/Kconfig"
source "drivers/net/ethernet/dlink/Kconfig"
source "drivers/net/ethernet/emulex/Kconfig"
source "drivers/net/ethernet/engleder/Kconfig"
source "drivers/net/ethernet/ezchip/Kconfig"
source "drivers/net/ethernet/faraday/Kconfig"
source "drivers/net/ethernet/freescale/Kconfig"
source "drivers/net/ethernet/fujitsu/Kconfig"
source "drivers/net/ethernet/fungible/Kconfig"
source "drivers/net/ethernet/google/Kconfig"
source "drivers/net/ethernet/hisilicon/Kconfig"
source "drivers/net/ethernet/huawei/Kconfig"
source "drivers/net/ethernet/i825xx/Kconfig"
source "drivers/net/ethernet/ibm/Kconfig"
source "drivers/net/ethernet/intel/Kconfig"
source "drivers/net/ethernet/wangxun/Kconfig"
source "drivers/net/ethernet/xscale/Kconfig"
config JME
tristate "JMicron(R) PCI-Express Gigabit Ethernet support"
depends on PCI
select CRC32
select MII
help
This driver supports the PCI-Express gigabit ethernet adapters
based on JMicron JMC250 chipset.
To compile this driver as a module, choose M here. The module
will be called jme.
config KORINA
tristate "Korina (IDT RC32434) Ethernet support"
depends on MIKROTIK_RB532 || COMPILE_TEST
select CRC32
select MII
help
If you have a Mikrotik RouterBoard 500 or IDT RC32434
based system say Y. Otherwise say N.
config LANTIQ_ETOP
tristate "Lantiq SoC ETOP driver"
depends on SOC_TYPE_XWAY
help
Support for the MII0 inside the Lantiq SoC
config LANTIQ_XRX200
tristate "Lantiq / Intel xRX200 PMAC network driver"
depends on SOC_TYPE_XWAY
help
Support for the PMAC of the Gigabit switch (GSWIP) inside the
Lantiq / Intel VRX200 VDSL SoC
source "drivers/net/ethernet/adi/Kconfig"
source "drivers/net/ethernet/litex/Kconfig"
source "drivers/net/ethernet/marvell/Kconfig"
source "drivers/net/ethernet/mediatek/Kconfig"
source "drivers/net/ethernet/mellanox/Kconfig"
source "drivers/net/ethernet/micrel/Kconfig"
source "drivers/net/ethernet/microchip/Kconfig"
source "drivers/net/ethernet/mscc/Kconfig"
source "drivers/net/ethernet/microsoft/Kconfig"
source "drivers/net/ethernet/moxa/Kconfig"
source "drivers/net/ethernet/myricom/Kconfig"
config FEALNX
tristate "Myson MTD-8xx PCI Ethernet support"
depends on PCI
select CRC32
select MII
help
Say Y here to support the Myson MTD-800 family of PCI-based Ethernet
cards. <http://www.myson.com.tw/>
source "drivers/net/ethernet/ni/Kconfig"
source "drivers/net/ethernet/natsemi/Kconfig"
source "drivers/net/ethernet/neterion/Kconfig"
source "drivers/net/ethernet/netronome/Kconfig"
source "drivers/net/ethernet/8390/Kconfig"
source "drivers/net/ethernet/nvidia/Kconfig"
source "drivers/net/ethernet/nxp/Kconfig"
source "drivers/net/ethernet/oki-semi/Kconfig"
config ETHOC
tristate "OpenCores 10/100 Mbps Ethernet MAC support"
depends on HAS_IOMEM && HAS_DMA
select MII
select PHYLIB
select CRC32
select BITREVERSE
help
Say Y here if you want to use the OpenCores 10/100 Mbps Ethernet MAC.
source "drivers/net/ethernet/packetengines/Kconfig"
source "drivers/net/ethernet/pasemi/Kconfig"
source "drivers/net/ethernet/pensando/Kconfig"
source "drivers/net/ethernet/qlogic/Kconfig"
source "drivers/net/ethernet/brocade/Kconfig"
source "drivers/net/ethernet/qualcomm/Kconfig"
source "drivers/net/ethernet/rdc/Kconfig"
source "drivers/net/ethernet/realtek/Kconfig"
source "drivers/net/ethernet/renesas/Kconfig"
source "drivers/net/ethernet/rocker/Kconfig"
source "drivers/net/ethernet/samsung/Kconfig"
source "drivers/net/ethernet/seeq/Kconfig"
source "drivers/net/ethernet/sgi/Kconfig"
source "drivers/net/ethernet/silan/Kconfig"
source "drivers/net/ethernet/sis/Kconfig"
source "drivers/net/ethernet/sfc/Kconfig"
source "drivers/net/ethernet/smsc/Kconfig"
source "drivers/net/ethernet/socionext/Kconfig"
source "drivers/net/ethernet/stmicro/Kconfig"
source "drivers/net/ethernet/sun/Kconfig"
source "drivers/net/ethernet/sunplus/Kconfig"
source "drivers/net/ethernet/synopsys/Kconfig"
source "drivers/net/ethernet/tehuti/Kconfig"
source "drivers/net/ethernet/ti/Kconfig"
source "drivers/net/ethernet/toshiba/Kconfig"
source "drivers/net/ethernet/tundra/Kconfig"
source "drivers/net/ethernet/vertexcom/Kconfig"
source "drivers/net/ethernet/via/Kconfig"
source "drivers/net/ethernet/wiznet/Kconfig"
source "drivers/net/ethernet/xilinx/Kconfig"
source "drivers/net/ethernet/xircom/Kconfig"
endif # ETHERNET
Reference in New Issue View Git Blame Copy Permalink