ac242e2cfd
pm8941 is missing the 5vs2 regulator node so let's add it since its needed to get the external display working. This regulator was already configured in the interrupts property on the parent node. Note that this regulator is referred to as mvs2 in the downstream MSM kernel sources. Signed-off-by: Brian Masney <masneyb@onstation.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
194 lines
4.5 KiB
Plaintext
194 lines
4.5 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0
|
|
#include <dt-bindings/iio/qcom,spmi-vadc.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include <dt-bindings/spmi/spmi.h>
|
|
|
|
&spmi_bus {
|
|
|
|
pm8941_0: pm8941@0 {
|
|
compatible = "qcom,pm8941", "qcom,spmi-pmic";
|
|
reg = <0x0 SPMI_USID>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
rtc@6000 {
|
|
compatible = "qcom,pm8941-rtc";
|
|
reg = <0x6000>,
|
|
<0x6100>;
|
|
reg-names = "rtc", "alarm";
|
|
interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
|
|
};
|
|
|
|
pwrkey@800 {
|
|
compatible = "qcom,pm8941-pwrkey";
|
|
reg = <0x800>;
|
|
interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
|
|
debounce = <15625>;
|
|
bias-pull-up;
|
|
};
|
|
|
|
usb_id: misc@900 {
|
|
compatible = "qcom,pm8941-misc";
|
|
reg = <0x900>;
|
|
interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>;
|
|
interrupt-names = "usb_id";
|
|
};
|
|
|
|
smbb: charger@1000 {
|
|
compatible = "qcom,pm8941-charger";
|
|
reg = <0x1000>;
|
|
interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
|
|
<0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
|
|
<0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
|
|
<0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
|
|
<0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
|
|
<0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
|
|
<0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
|
|
<0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
|
|
interrupt-names = "chg-done",
|
|
"chg-fast",
|
|
"chg-trkl",
|
|
"bat-temp-ok",
|
|
"bat-present",
|
|
"chg-gone",
|
|
"usb-valid",
|
|
"dc-valid";
|
|
|
|
usb-otg-in-supply = <&pm8941_5vs1>;
|
|
|
|
chg_otg: otg-vbus { };
|
|
};
|
|
|
|
pm8941_gpios: gpios@c000 {
|
|
compatible = "qcom,pm8941-gpio", "qcom,spmi-gpio";
|
|
reg = <0xc000>;
|
|
gpio-controller;
|
|
gpio-ranges = <&pm8941_gpios 0 0 36>;
|
|
#gpio-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
|
|
boost_bypass_n_pin: boost-bypass {
|
|
pins = "gpio21";
|
|
function = "normal";
|
|
};
|
|
};
|
|
|
|
pm8941_mpps: mpps@a000 {
|
|
compatible = "qcom,pm8941-mpp", "qcom,spmi-mpp";
|
|
reg = <0xa000>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
interrupts = <0 0xa0 0 IRQ_TYPE_NONE>,
|
|
<0 0xa1 0 IRQ_TYPE_NONE>,
|
|
<0 0xa2 0 IRQ_TYPE_NONE>,
|
|
<0 0xa3 0 IRQ_TYPE_NONE>,
|
|
<0 0xa4 0 IRQ_TYPE_NONE>,
|
|
<0 0xa5 0 IRQ_TYPE_NONE>,
|
|
<0 0xa6 0 IRQ_TYPE_NONE>,
|
|
<0 0xa7 0 IRQ_TYPE_NONE>;
|
|
};
|
|
|
|
pm8941_temp: temp-alarm@2400 {
|
|
compatible = "qcom,spmi-temp-alarm";
|
|
reg = <0x2400>;
|
|
interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
|
|
io-channels = <&pm8941_vadc VADC_DIE_TEMP>;
|
|
io-channel-names = "thermal";
|
|
#thermal-sensor-cells = <0>;
|
|
};
|
|
|
|
pm8941_vadc: vadc@3100 {
|
|
compatible = "qcom,spmi-vadc";
|
|
reg = <0x3100>;
|
|
interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
#io-channel-cells = <1>;
|
|
|
|
bat_temp {
|
|
reg = <VADC_LR_MUX1_BAT_THERM>;
|
|
};
|
|
die_temp {
|
|
reg = <VADC_DIE_TEMP>;
|
|
};
|
|
ref_625mv {
|
|
reg = <VADC_REF_625MV>;
|
|
};
|
|
ref_1250v {
|
|
reg = <VADC_REF_1250MV>;
|
|
};
|
|
ref_gnd {
|
|
reg = <VADC_GND_REF>;
|
|
};
|
|
ref_vdd {
|
|
reg = <VADC_VDD_VADC>;
|
|
};
|
|
vbat_sns {
|
|
reg = <VADC_VBAT_SNS>;
|
|
};
|
|
};
|
|
|
|
pm8941_iadc: iadc@3600 {
|
|
compatible = "qcom,pm8941-iadc", "qcom,spmi-iadc";
|
|
reg = <0x3600>;
|
|
interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>;
|
|
qcom,external-resistor-micro-ohms = <10000>;
|
|
};
|
|
|
|
coincell@2800 {
|
|
compatible = "qcom,pm8941-coincell";
|
|
reg = <0x2800>;
|
|
status = "disabled";
|
|
};
|
|
};
|
|
|
|
pm8941_1: pm8941@1 {
|
|
compatible = "qcom,pm8941", "qcom,spmi-pmic";
|
|
reg = <0x1 SPMI_USID>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pm8941_wled: wled@d800 {
|
|
compatible = "qcom,pm8941-wled";
|
|
reg = <0xd800>;
|
|
label = "backlight";
|
|
|
|
status = "disabled";
|
|
};
|
|
|
|
regulators {
|
|
compatible = "qcom,pm8941-regulators";
|
|
interrupts = <0x1 0x83 0x2 0>, <0x1 0x84 0x2 0>;
|
|
interrupt-names = "ocp-5vs1", "ocp-5vs2";
|
|
vin_5vs-supply = <&pm8941_5v>;
|
|
|
|
pm8941_5v: s4 {
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
regulator-enable-ramp-delay = <500>;
|
|
};
|
|
|
|
pm8941_5vs1: 5vs1 {
|
|
regulator-enable-ramp-delay = <1000>;
|
|
regulator-pull-down;
|
|
regulator-over-current-protection;
|
|
qcom,ocp-max-retries = <10>;
|
|
qcom,ocp-retry-delay = <30>;
|
|
qcom,vs-soft-start-strength = <0>;
|
|
regulator-initial-mode = <1>;
|
|
};
|
|
|
|
pm8941_5vs2: 5vs2 {
|
|
regulator-enable-ramp-delay = <1000>;
|
|
regulator-pull-down;
|
|
regulator-over-current-protection;
|
|
qcom,ocp-max-retries = <10>;
|
|
qcom,ocp-retry-delay = <30>;
|
|
qcom,vs-soft-start-strength = <0>;
|
|
regulator-initial-mode = <1>;
|
|
};
|
|
};
|
|
};
|
|
};
|