de9c0d49d8
While building arm32 allyesconfig, I ran into the following errors:
arch/arm/lib/xor-neon.c:17:2: error: You should compile this file with
'-mfloat-abi=softfp -mfpu=neon'
In file included from lib/raid6/neon1.c:27:
/home/nathan/cbl/prebuilt/lib/clang/8.0.0/include/arm_neon.h:28:2:
error: "NEON support not enabled"
Building V=1 showed NEON_FLAGS getting passed along to Clang but
__ARM_NEON__ was not getting defined. Ultimately, it boils down to Clang
only defining __ARM_NEON__ when targeting armv7, rather than armv6k,
which is the '-march' value for allyesconfig.
>From lib/Basic/Targets/ARM.cpp in the Clang source:
// This only gets set when Neon instructions are actually available, unlike
// the VFP define, hence the soft float and arch check. This is subtly
// different from gcc, we follow the intent which was that it should be set
// when Neon instructions are actually available.
if ((FPU & NeonFPU) && !SoftFloat && ArchVersion >= 7) {
Builder.defineMacro("__ARM_NEON", "1");
Builder.defineMacro("__ARM_NEON__");
// current AArch32 NEON implementations do not support double-precision
// floating-point even when it is present in VFP.
Builder.defineMacro("__ARM_NEON_FP",
"0x" + Twine::utohexstr(HW_FP & ~HW_FP_DP));
}
Ard Biesheuvel recommended explicitly adding '-march=armv7-a' at the
beginning of the NEON_FLAGS definitions so that __ARM_NEON__ always gets
definined by Clang. This doesn't functionally change anything because
that code will only run where NEON is supported, which is implicitly
armv7.
Link: https://github.com/ClangBuiltLinux/linux/issues/287
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
122 lines
5.6 KiB
Plaintext
122 lines
5.6 KiB
Plaintext
Kernel mode NEON
|
|
================
|
|
|
|
TL;DR summary
|
|
-------------
|
|
* Use only NEON instructions, or VFP instructions that don't rely on support
|
|
code
|
|
* Isolate your NEON code in a separate compilation unit, and compile it with
|
|
'-march=armv7-a -mfpu=neon -mfloat-abi=softfp'
|
|
* Put kernel_neon_begin() and kernel_neon_end() calls around the calls into your
|
|
NEON code
|
|
* Don't sleep in your NEON code, and be aware that it will be executed with
|
|
preemption disabled
|
|
|
|
|
|
Introduction
|
|
------------
|
|
It is possible to use NEON instructions (and in some cases, VFP instructions) in
|
|
code that runs in kernel mode. However, for performance reasons, the NEON/VFP
|
|
register file is not preserved and restored at every context switch or taken
|
|
exception like the normal register file is, so some manual intervention is
|
|
required. Furthermore, special care is required for code that may sleep [i.e.,
|
|
may call schedule()], as NEON or VFP instructions will be executed in a
|
|
non-preemptible section for reasons outlined below.
|
|
|
|
|
|
Lazy preserve and restore
|
|
-------------------------
|
|
The NEON/VFP register file is managed using lazy preserve (on UP systems) and
|
|
lazy restore (on both SMP and UP systems). This means that the register file is
|
|
kept 'live', and is only preserved and restored when multiple tasks are
|
|
contending for the NEON/VFP unit (or, in the SMP case, when a task migrates to
|
|
another core). Lazy restore is implemented by disabling the NEON/VFP unit after
|
|
every context switch, resulting in a trap when subsequently a NEON/VFP
|
|
instruction is issued, allowing the kernel to step in and perform the restore if
|
|
necessary.
|
|
|
|
Any use of the NEON/VFP unit in kernel mode should not interfere with this, so
|
|
it is required to do an 'eager' preserve of the NEON/VFP register file, and
|
|
enable the NEON/VFP unit explicitly so no exceptions are generated on first
|
|
subsequent use. This is handled by the function kernel_neon_begin(), which
|
|
should be called before any kernel mode NEON or VFP instructions are issued.
|
|
Likewise, the NEON/VFP unit should be disabled again after use to make sure user
|
|
mode will hit the lazy restore trap upon next use. This is handled by the
|
|
function kernel_neon_end().
|
|
|
|
|
|
Interruptions in kernel mode
|
|
----------------------------
|
|
For reasons of performance and simplicity, it was decided that there shall be no
|
|
preserve/restore mechanism for the kernel mode NEON/VFP register contents. This
|
|
implies that interruptions of a kernel mode NEON section can only be allowed if
|
|
they are guaranteed not to touch the NEON/VFP registers. For this reason, the
|
|
following rules and restrictions apply in the kernel:
|
|
* NEON/VFP code is not allowed in interrupt context;
|
|
* NEON/VFP code is not allowed to sleep;
|
|
* NEON/VFP code is executed with preemption disabled.
|
|
|
|
If latency is a concern, it is possible to put back to back calls to
|
|
kernel_neon_end() and kernel_neon_begin() in places in your code where none of
|
|
the NEON registers are live. (Additional calls to kernel_neon_begin() should be
|
|
reasonably cheap if no context switch occurred in the meantime)
|
|
|
|
|
|
VFP and support code
|
|
--------------------
|
|
Earlier versions of VFP (prior to version 3) rely on software support for things
|
|
like IEEE-754 compliant underflow handling etc. When the VFP unit needs such
|
|
software assistance, it signals the kernel by raising an undefined instruction
|
|
exception. The kernel responds by inspecting the VFP control registers and the
|
|
current instruction and arguments, and emulates the instruction in software.
|
|
|
|
Such software assistance is currently not implemented for VFP instructions
|
|
executed in kernel mode. If such a condition is encountered, the kernel will
|
|
fail and generate an OOPS.
|
|
|
|
|
|
Separating NEON code from ordinary code
|
|
---------------------------------------
|
|
The compiler is not aware of the special significance of kernel_neon_begin() and
|
|
kernel_neon_end(), i.e., that it is only allowed to issue NEON/VFP instructions
|
|
between calls to these respective functions. Furthermore, GCC may generate NEON
|
|
instructions of its own at -O3 level if -mfpu=neon is selected, and even if the
|
|
kernel is currently compiled at -O2, future changes may result in NEON/VFP
|
|
instructions appearing in unexpected places if no special care is taken.
|
|
|
|
Therefore, the recommended and only supported way of using NEON/VFP in the
|
|
kernel is by adhering to the following rules:
|
|
* isolate the NEON code in a separate compilation unit and compile it with
|
|
'-march=armv7-a -mfpu=neon -mfloat-abi=softfp';
|
|
* issue the calls to kernel_neon_begin(), kernel_neon_end() as well as the calls
|
|
into the unit containing the NEON code from a compilation unit which is *not*
|
|
built with the GCC flag '-mfpu=neon' set.
|
|
|
|
As the kernel is compiled with '-msoft-float', the above will guarantee that
|
|
both NEON and VFP instructions will only ever appear in designated compilation
|
|
units at any optimization level.
|
|
|
|
|
|
NEON assembler
|
|
--------------
|
|
NEON assembler is supported with no additional caveats as long as the rules
|
|
above are followed.
|
|
|
|
|
|
NEON code generated by GCC
|
|
--------------------------
|
|
The GCC option -ftree-vectorize (implied by -O3) tries to exploit implicit
|
|
parallelism, and generates NEON code from ordinary C source code. This is fully
|
|
supported as long as the rules above are followed.
|
|
|
|
|
|
NEON intrinsics
|
|
---------------
|
|
NEON intrinsics are also supported. However, as code using NEON intrinsics
|
|
relies on the GCC header <arm_neon.h>, (which #includes <stdint.h>), you should
|
|
observe the following in addition to the rules above:
|
|
* Compile the unit containing the NEON intrinsics with '-ffreestanding' so GCC
|
|
uses its builtin version of <stdint.h> (this is a C99 header which the kernel
|
|
does not supply);
|
|
* Include <arm_neon.h> last, or at least after <linux/types.h>
|