iv/linux
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
b4dc38fd45
linux/drivers/usb/musb
History
Felipe Balbi b4dc38fd45 usb: musb: core: simplify musb_recover_work() 
we're not resetting musb at all, just restarting
the session. This means we don't need to touch PHYs
or VBUS or anything like that. Just make sure session
bit is reenabled after MUSB dropped it.

while at that, make sure to tell usbcore that we're
dropping the session and, thus, disconnecting the
device.

Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-03-10 15:33:29 -05:00
..
am35x.c usb: musb: Change end point selection to use new IO access 2014-11-25 08:47:06 -06:00
blackfin.c usb: musb: blackfin: remove incorrect __exit_p() 2015-02-02 13:04:55 -06:00
blackfin.h
cppi_dma.c usb: musb: dma: merge ->start/stop into create/destroy 2013-07-29 13:53:18 +03:00
cppi_dma.h
da8xx.c usb: musb: Pass fifo_mode in platform data 2014-11-25 08:47:07 -06:00
davinci.c usb: move the OTG state from the USB PHY to the OTG structure 2014-11-03 10:01:25 -06:00
davinci.h
jz4740.c usb: musb: Pass fifo_mode in platform data 2014-11-25 08:47:07 -06:00
Kconfig usb: musb: add omap-control dependency 2015-01-29 10:36:29 -06:00
Makefile usb: musb: add support for JZ4740 usb device controller 2013-12-20 09:53:24 -06:00
musb_am335x.c usb: musb: Fix panic upon musb_am335x module removal 2014-06-27 10:53:06 -05:00
musb_core.c usb: musb: core: simplify musb_recover_work() 2015-03-10 15:33:29 -05:00
musb_core.h usb: musb: Use IS_ENABLED for tusb6010 2014-11-25 08:47:07 -06:00
musb_cppi41.c usb: musb: cppi41: improve rx channel abort routine 2015-01-27 09:34:58 -06:00
musb_debug.h
musb_debugfs.c Linux 3.19-rc5 2015-01-19 09:57:20 -06:00
musb_dma.h usb: musb: introduce dma_channel.rx_packet_done 2014-06-30 14:26:24 -05:00
musb_dsps.c usb: musb: dsps: do not reset musb on babble 2015-03-10 15:33:28 -05:00
musb_gadget_ep0.c usb: musb: gadget: use common is_selfpowered 2015-01-29 10:35:43 -06:00
musb_gadget.c usb: musb: gadget: get rid of stop_activity() 2015-03-09 10:38:48 -05:00
musb_gadget.h usb: musb: add Kconfig options for HOST, GAGDET or DUAL_ROLE modes 2013-05-28 19:22:23 +03:00
musb_host.c usb: musb: musb_host: Enable HCD_BH flag to handle urb return in bottom half 2015-02-23 00:04:52 -06:00
musb_host.h usb: musb: fix prototype for musb_port_reset 2013-12-20 15:05:43 -06:00
musb_io.h usb: musb: Change end point selection to use new IO access 2014-11-25 08:47:06 -06:00
musb_regs.h usb: musb: Use IS_ENABLED for tusb6010 2014-11-25 08:47:07 -06:00
musb_virthub.c usb: musb: fix device hotplug behind hub 2015-02-04 11:16:47 -06:00
musbhsdma.c usb: musb: Change end point selection to use new IO access 2014-11-25 08:47:06 -06:00
musbhsdma.h
omap2430.c usb: musb: Fix use for of_property_read_bool for disabled multipoint 2015-02-23 09:14:30 -06:00
omap2430.h usb: start using the control module driver 2013-01-25 12:27:24 +02:00
tusb6010_omap.c usb: musb: tusb6010: Use musb->tusb_revision instead of tusb_get_revision call. 2014-05-16 12:16:31 -05:00
tusb6010.c usb: musb: Change end point selection to use new IO access 2014-11-25 08:47:06 -06:00
tusb6010.h usb: musb: tusb6010: Use musb->tusb_revision instead of tusb_get_revision call. 2014-05-16 12:16:31 -05:00
ux500_dma.c usb: musb: Change to use new IO access 2014-11-25 08:47:06 -06:00
ux500.c usb: musb: Pass fifo_mode in platform data 2014-11-25 08:47:07 -06:00