4c5a410d3b
Add temperature alarm and thermal zone configuration to all three pm8150 instances. Configuration is largely based on the msm-4.19 tree. These alarms use main adc of the pmic. Separate temperature adc is not supported yet. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20200621192824.2069145-3-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
126 lines
2.4 KiB
Plaintext
126 lines
2.4 KiB
Plaintext
// SPDX-License-Identifier: BSD-3-Clause
|
|
/*
|
|
* Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
|
|
* Copyright (c) 2019, Linaro Limited
|
|
*/
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include <dt-bindings/spmi/spmi.h>
|
|
#include <dt-bindings/iio/qcom,spmi-vadc.h>
|
|
|
|
/ {
|
|
thermal-zones {
|
|
pm8150 {
|
|
polling-delay-passive = <100>;
|
|
polling-delay = <0>;
|
|
|
|
thermal-sensors = <&pm8150_temp>;
|
|
|
|
trips {
|
|
trip0 {
|
|
temperature = <95000>;
|
|
hysteresis = <0>;
|
|
type = "passive";
|
|
};
|
|
|
|
trip1 {
|
|
temperature = <115000>;
|
|
hysteresis = <0>;
|
|
type = "hot";
|
|
};
|
|
|
|
trip2 {
|
|
temperature = <145000>;
|
|
hysteresis = <0>;
|
|
type = "critical";
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&spmi_bus {
|
|
pm8150_0: pmic@0 {
|
|
compatible = "qcom,pm8150", "qcom,spmi-pmic";
|
|
reg = <0x0 SPMI_USID>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pon: power-on@800 {
|
|
compatible = "qcom,pm8916-pon";
|
|
reg = <0x0800>;
|
|
pwrkey {
|
|
compatible = "qcom,pm8941-pwrkey";
|
|
interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>;
|
|
debounce = <15625>;
|
|
bias-pull-up;
|
|
linux,code = <KEY_POWER>;
|
|
|
|
status = "disabled";
|
|
};
|
|
};
|
|
|
|
pm8150_temp: temp-alarm@2400 {
|
|
compatible = "qcom,spmi-temp-alarm";
|
|
reg = <0x2400>;
|
|
interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
|
|
io-channels = <&pm8150_adc ADC5_DIE_TEMP>;
|
|
io-channel-names = "thermal";
|
|
#thermal-sensor-cells = <0>;
|
|
};
|
|
|
|
pm8150_adc: adc@3100 {
|
|
compatible = "qcom,spmi-adc5";
|
|
reg = <0x3100>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
#io-channel-cells = <1>;
|
|
interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
|
|
|
|
ref-gnd@0 {
|
|
reg = <ADC5_REF_GND>;
|
|
qcom,pre-scaling = <1 1>;
|
|
label = "ref_gnd";
|
|
};
|
|
|
|
vref-1p25@1 {
|
|
reg = <ADC5_1P25VREF>;
|
|
qcom,pre-scaling = <1 1>;
|
|
label = "vref_1p25";
|
|
};
|
|
|
|
die-temp@6 {
|
|
reg = <ADC5_DIE_TEMP>;
|
|
qcom,pre-scaling = <1 1>;
|
|
label = "die_temp";
|
|
};
|
|
};
|
|
|
|
rtc@6000 {
|
|
compatible = "qcom,pm8941-rtc";
|
|
reg = <0x6000>;
|
|
reg-names = "rtc", "alarm";
|
|
interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
|
|
|
|
status = "disabled";
|
|
};
|
|
|
|
pm8150_gpios: gpio@c000 {
|
|
compatible = "qcom,pm8150-gpio";
|
|
reg = <0xc000>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
};
|
|
|
|
pmic@1 {
|
|
compatible = "qcom,pm8150", "qcom,spmi-pmic";
|
|
reg = <0x1 SPMI_USID>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
};
|
|
};
|