linux

iv/linux

History

Arnd Bergmann cdcdbbf350 Renesas ARM Based SoC DT Updates for v4.17

* Silk board with R-Car E2 (r8a7794) SoC
   - Add r1ex24002 EEPROM to DT
 
     Magnus Damm says "Extend the Silk board support to include U14 which is
     an I2C based EEPROM hooked up to the I2C1 bus."
 
   - Add GPIO keys to DT
 
     Magnus Damm says "Extend the Silk board support to include SW3, SW4,
     SW6 and SW12. They are all connected via GPIO lines and handled by the
     gpio-keys driver"
 
 * Marzen board with R-Car H1 (r7a7779) SoC
   - Add SDHI0 VCCQ Regulator
 
     Magnus Damm says "Add support for the on-board voltage regulator hooked
     up to GPIO3_20 on r8a7779 Marzen. The board schematics describes the
     regulator as U4 TPS2110A. Input wise, U4 has D0 fixed to ground, D1
     tied to GPIO3_20 while IN1 is fixed to 3.3V and IN2 is fixed to 1.8V.
     OUT goes to the pull-ups for the data pins of SDHI0."
 
 * Porter board with R-Car M3W (r8a7791) SoC
   - Fix HDMI output routing
 
     Laurent Pinchart says "The HDMI encoder is connected to the RGB output
     of the DU, which is port@0, not port@1."
 
 * iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM) and
   iWave Systems RZ/G1M Qseven System On Module (iW-RainboW-G20M-Qseven)
   - Enable cmt0
 
 * Stout board with R-Car H2 (r8a7790) SoC
   - Initial support
 
 * Lager board with R-Car H2 (r8a7790) SoC
   - Add CEC clock for HDMI transmitter
 
     Niklas Söderlund says "The adv7511 on the Lager board has a 12 MHz
     fixed clock for the CEC block. Specify this in the dts to enable CEC
     support."
 
   - Move cec_clock to root node
 
     By definition nodes without a bus address do not belong on the bus
 
 * kzm9d board with EMMA Mobile EV2 (EMEV2) SoC
   - Fix "debounce-interval" property misspelling
 
 * RZ/G1M (r8a7743) and RZ/G1H (r8a7745) SoCs
   - Add IPMMU DT nodes
   - Add VSP support
 
 * R-Car Gen2 boards
   - Use I2C demuxer for
 
     This allows run-time switching between alternate I2C IP blocks
 
 * R-Car Gen2 and RZ/G1 SoCs
   - Clean up DT files to ease future maintenance
     + add soc node for IP attached to the bus
     + sort subnodes of soc and root node
     + consistently use single space after =
 
 * R-Car H2 (r8a7790), M3-W (r8a7791) and M3-N (r7a7793) SoCs
   - Reduce size of thermal registers
 
     According to the "User's Manual: Hardware" v2.00 the registers at base
     0xe61f0000 extend to an offset of 0x10, rather than 0x14 which is the
     case on the r8a73a4 (R-Mobile APE6).
 
     This should not have any runtime affect as mapping granularity is
     PAGE_SIZE.
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCAAdFiEE4nzZofWswv9L/nKF189kaWo3T74FAlqr8gsACgkQ189kaWo3
 T74DQw//Th3KG2mycxuvsMEQ2nMRlnDet1Sn3+A85i7TiXs8HLZ7gJlqHV7tEmAV
 Mdflu01Q4Uu6STkLe8MagDl42Hi8B751VSp97RwLUOuWrNHlMVNsBCWYAOnP8LEM
 D7jxlNde5bakP3DlwC/y/evx7cJMt9186QAsqO6AyD6kbw5pdNy8aNjZ4S3sB68W
 Y4HkYFG8ScpNCgfSB2Z60GMIGXAIHBFCullITpzie7zknp57nYn74MEUKhCjxIEm
 PaR+KBDLcckJdsu5VCrHVWDHAYfN3ETx3WLJNn9vxuDqEOHV9Do7AiGyHEmuLAWU
 Aijlp1SHVSwvSXFEodRRvugEy7/7GP6SHT7XdUKcdlp1KrP+YRlS4zccHwUhVn/Z
 G+SCvxVFk902Rk2UFVkk/MayUanxo8VjvDzveWEQr6k3mGmIQt6LugZG4guYgyQh
 A6pkvW8AvUcSX2BDawxKj6rvEDZBLbvKsdybUybHLg7IzCWPzCTg+NKDMlI9rB8I
 wpdDJIX1/Efe1aa85AfNA8yNQBsZzA//gXj+La+vo8N/ptkKkO9EC13rgjVwIepV
 ccUDjssFvUoQy9THW/PwHPczDcj/t9rIfsiilX5zQdt5dqwp0cw5hMAm2wQvdc0n
 4Ge5nBI121eCJ2f4RAghz89t0Dh8yUDdluJCKFHas+x9/JZPAYU=
 =dZnw
 -----END PGP SIGNATURE-----

Merge tag 'renesas-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Pull "Renesas ARM Based SoC DT Updates for v4.17" from Simon Horman:

* Silk board with R-Car E2 (r8a7794) SoC
  - Add r1ex24002 EEPROM to DT

    Magnus Damm says "Extend the Silk board support to include U14 which is
    an I2C based EEPROM hooked up to the I2C1 bus."

  - Add GPIO keys to DT

    Magnus Damm says "Extend the Silk board support to include SW3, SW4,
    SW6 and SW12. They are all connected via GPIO lines and handled by the
    gpio-keys driver"

* Marzen board with R-Car H1 (r7a7779) SoC
  - Add SDHI0 VCCQ Regulator

    Magnus Damm says "Add support for the on-board voltage regulator hooked
    up to GPIO3_20 on r8a7779 Marzen. The board schematics describes the
    regulator as U4 TPS2110A. Input wise, U4 has D0 fixed to ground, D1
    tied to GPIO3_20 while IN1 is fixed to 3.3V and IN2 is fixed to 1.8V.
    OUT goes to the pull-ups for the data pins of SDHI0."

* Porter board with R-Car M3W (r8a7791) SoC
  - Fix HDMI output routing

    Laurent Pinchart says "The HDMI encoder is connected to the RGB output
    of the DU, which is port@0, not port@1."

* iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM) and
  iWave Systems RZ/G1M Qseven System On Module (iW-RainboW-G20M-Qseven)
  - Enable cmt0

* Stout board with R-Car H2 (r8a7790) SoC
  - Initial support

* Lager board with R-Car H2 (r8a7790) SoC
  - Add CEC clock for HDMI transmitter

    Niklas Söderlund says "The adv7511 on the Lager board has a 12 MHz
    fixed clock for the CEC block. Specify this in the dts to enable CEC
    support."

  - Move cec_clock to root node

    By definition nodes without a bus address do not belong on the bus

* kzm9d board with EMMA Mobile EV2 (EMEV2) SoC
  - Fix "debounce-interval" property misspelling

* RZ/G1M (r8a7743) and RZ/G1H (r8a7745) SoCs
  - Add IPMMU DT nodes
  - Add VSP support

* R-Car Gen2 boards
  - Use I2C demuxer for

    This allows run-time switching between alternate I2C IP blocks

* R-Car Gen2 and RZ/G1 SoCs
  - Clean up DT files to ease future maintenance
    + add soc node for IP attached to the bus
    + sort subnodes of soc and root node
    + consistently use single space after =

* R-Car H2 (r8a7790), M3-W (r8a7791) and M3-N (r7a7793) SoCs
  - Reduce size of thermal registers

    According to the "User's Manual: Hardware" v2.00 the registers at base
    0xe61f0000 extend to an offset of 0x10, rather than 0x14 which is the
    case on the r8a73a4 (R-Mobile APE6).

    This should not have any runtime affect as mapping granularity is
    PAGE_SIZE.

* tag 'renesas-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (47 commits)
  ARM: dts: silk: Add GPIO keys to DT
  ARM: dts: silk: Add r1ex24002 EEPROM to DT
  ARM: dts: marzen: Add SDHI0 VCCQ Regulator
  ARM: dts: stout: Initial r8a7790 Stout board support
  ARM: dts: lager: Move cec_clock to root node
  ARM: dts: kzm9d: Fix "debounce-interval" property misspelling
  ARM: dts: gose: use demuxer for I2C4
  ARM: dts: gose: use demuxer for I2C2
  ARM: dts: silk: use demuxer for I2C1
  ARM: dts: alt: use demuxer for I2C1
  ARM: dts: porter: use demuxer for I2C2
  ARM: dts: koelsch: use demuxer for I2C4
  ARM: dts: koelsch: use demuxer for I2C2
  ARM: dts: lager: use demuxer for IIC3/I2C3
  ARM: dts: lager: use demuxer for IIC2/I2C2
  ARM: dts: r8a7745: Add VSP support
  ARM: dts: r8a7743: Add VSP support
  ARM: dts: r8a7745: Add IPMMU DT nodes
  ARM: dts: r8a7743: Add IPMMU DT nodes
  ARM: dts: r8a7745: sort subnodes of soc node
  ...

2018-03-27 13:32:53 +02:00

alpha

locking/xchg/alpha: Fix xchg() and cmpxchg() memory ordering bugs

2018-02-23 08:38:16 +01:00

arc

ARC fixes for 4.16-rc4

2018-03-01 14:32:23 -08:00

arm

Renesas ARM Based SoC DT Updates for v4.17

2018-03-27 13:32:53 +02:00

arm64

Renesas ARM64 Based SoC DT Updates for v4.17