d3dbd7a6aa
Kunihiko Hayashi says: ==================== net: add UniPhier AVE ethernet support This series adds support for Socionext AVE ethernet controller implemented on UniPhier SoCs. This driver supports RGMII/RMII modes. v8: https://www.spinics.net/lists/netdev/msg474374.html The PHY patch included in v1 has already separated in: http://www.spinics.net/lists/netdev/msg454595.html Changes since v8: - move operators at the beginning of the line to the end of the previous line - dt-bindings: add blank lines before mdio and phy subnodes Changes since v7: - dt-bindings: fix mdio subnode description Changes since v6: - sort the order of local variables from longest to shortest line - fix ave_probe() which calls register_netdev() at the end of initialization - dt-bindings: remove phy node descriptions in mdio node Changes since v5: - replace license boilerplate with SPDX Identifier - remove inline directives and an unused function Changes since v4: - fix larger integer warning on AVE_PFMBYTE_MASK0 Changes since v3: - remove checking dma address and use dma_set_mask() to restirct address - replace ave_mdio_busywait() with read_poll_timeout() - replace functions to access to registers with readl/writel() directly - replace a function to access to macaddr with ave_hw_write_macaddr() - change return value of ave_dma_map() to error value - move mdiobus_unregister() from ave_remove() to ave_uninit() - eliminate else block at the end of ave_dma_map() - add mask definitions for packet filter - sort bitmap definitions in descending order - add error check to some functions - rename and sort functions to clear sub-categories - fix error value consistency - remove unneeded initializers - change type of constant arrays Changes since v2: - replace clk_get() with devm_clk_get() - replace reset_control_get() with devm_reset_control_get_optional_shared() - add error return when the error occurs on the above *_get functions - sort soc data and compatible strings - remove clearly obvious comments - modify dt-bindings document consistent with these modifications Changes since v1: - add/remove devicetree properties and sub-node - remove "internal-phy-interrupt" and "desc-bits" property - add SoC data structures based on compatible strings - add node operation to apply "mdio" sub-node - add support for features - add support for {get,set}_pauseparam and pause frame operations - add support for ndo_get_stats64 instead of ndo_get_stats - replace with desiable functions - replace check for valid phy_mode with phy_interface{_mode}_is_rgmii() - replace phy attach message with phy_attached_info() - replace 32bit operation with {upper,lower}_32_bits() on ave_wdesc_addr() - replace nway_reset and get_link with generic functions - move operations to proper functions - move phy_start_aneg() to ndo_open, and remove unnecessary PHY interrupt operations See http://www.spinics.net/lists/netdev/msg454590.html - move irq initialization and descriptor memory allocation to ndo_open - move initialization of reset and clock and mdiobus to ndo_init - fix skbuffer operations - fix skb alignment operations and add Rx buffer adjustment for descriptor See http://www.spinics.net/lists/netdev/msg456014.html - add error returns when dma_map_single() failed - clean up code structures - clean up wait-loop and wake-queue conditions - add ave_wdesc_addr() and offset definitions - add ave_macaddr_init() to clean up mac-address operation - fix checking whether Tx entry is not enough - fix supported features of phydev - add necessary free/disable operations - add phydev check on ave_{get,set}_wol() - remove netif_carrier functions, phydev initializer, and Tx budget check - change obsolate codes - replace ndev->{base_addr,irq} with the members of ave_private - rename goto labels and mask definitions, and remove unused codes ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
Linux kernel ============ This file was moved to Documentation/admin-guide/README.rst Please notice that there are several guides for kernel developers and users. These guides can be rendered in a number of formats, like HTML and PDF. In order to build the documentation, use ``make htmldocs`` or ``make pdfdocs``. There are various text files in the Documentation/ subdirectory, several of them using the Restructured Text markup notation. See Documentation/00-INDEX for a list of what is contained in each file. Please read the Documentation/process/changes.rst file, as it contains the requirements for building and running the kernel, and information about the problems which may result by upgrading your kernel.