linux/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts
Stefan Agner c183c406c4 arm64: dts: meson: fix PHY deassert timing requirements
According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
registers. This fixes an issue seen on ODROID-C2 where the Ethernet
link doesn't come up when using ip link set down/up:
  [ 6630.714855] meson8b-dwmac c9410000.ethernet eth0: Link is Down
  [ 6630.785775] meson8b-dwmac c9410000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=36)
  [ 6630.893071] meson8b-dwmac c9410000.ethernet: Failed to reset the dma
  [ 6630.893800] meson8b-dwmac c9410000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
  [ 6630.902835] meson8b-dwmac c9410000.ethernet eth0: stmmac_open: Hw setup failed

Fixes: f29cabf240ed ("arm64: dts: meson: use the generic Ethernet PHY reset GPIO bindings")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/4a322c198b86e4c8b3dda015560a683babea4d63.1607363522.git.stefan@agner.ch
2020-12-07 11:12:49 -08:00

112 lines
2.1 KiB
Plaintext

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (c) 2016 Endless Computers, Inc.
* Author: Carlo Caione <carlo@endlessm.com>
*/
/dts-v1/;
#include <dt-bindings/input/input.h>
#include "meson-gxl-s905d.dtsi"
#include "meson-gx-p23x-q20x.dtsi"
/ {
compatible = "amlogic,p230", "amlogic,s905d", "amlogic,meson-gxl";
model = "Amlogic Meson GXL (S905D) P230 Development Board";
adc-keys {
compatible = "adc-keys";
io-channels = <&saradc 0>;
io-channel-names = "buttons";
keyup-threshold-microvolt = <1710000>;
button-function {
label = "Update";
linux,code = <KEY_VENDOR>;
press-threshold-microvolt = <10000>;
};
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <100>;
button@0 {
label = "power";
linux,code = <KEY_POWER>;
gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
};
};
hdmi-connector {
compatible = "hdmi-connector";
type = "a";
port {
hdmi_connector_in: endpoint {
remote-endpoint = <&hdmi_tx_tmds_out>;
};
};
};
};
&cec_AO {
status = "okay";
pinctrl-0 = <&ao_cec_pins>;
pinctrl-names = "default";
hdmi-phandle = <&hdmi_tx>;
};
/* P230 has exclusive choice between internal or external PHY */
&ethmac {
pinctrl-0 = <&eth_pins>;
pinctrl-names = "default";
/* Select external PHY by default */
phy-handle = <&external_phy>;
amlogic,tx-delay-ns = <2>;
/* External PHY is in RGMII */
phy-mode = "rgmii";
};
&external_mdio {
external_phy: ethernet-phy@0 {
/* Realtek RTL8211F (0x001cc916) */
reg = <0>;
max-speed = <1000>;
/* External PHY reset is shared with internal PHY Led signal */
reset-assert-us = <10000>;
reset-deassert-us = <80000>;
reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
interrupt-parent = <&gpio_intc>;
interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
eee-broken-1000t;
};
};
&hdmi_tx {
status = "okay";
pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
pinctrl-names = "default";
};
&hdmi_tx_tmds_port {
hdmi_tx_tmds_out: endpoint {
remote-endpoint = <&hdmi_connector_in>;
};
};
&sd_emmc_a {
brcmf: wifi@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
};
};