396e4dd89d
There is no point in sharing any definitions between the R2 and R3 versions of the TVK1281618 UIB. The proximity sensor collides with the touchscreen etc, it is less confusing to get rid of the overarching TVK1281618 UIB file and just use one for each. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
284 lines
7.4 KiB
Plaintext
284 lines
7.4 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later
|
|
/*
|
|
* Device Tree for the TVK1281618 R2 user interface board (UIB)
|
|
*/
|
|
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&prox_tvk_mode>, <&hall_tvk_mode>;
|
|
|
|
button@139 {
|
|
/* Proximity sensor */
|
|
gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>;
|
|
linux,code = <11>; /* SW_FRONT_PROXIMITY */
|
|
label = "SFH7741 Proximity Sensor";
|
|
};
|
|
button@145 {
|
|
/* Hall sensor */
|
|
gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
|
|
linux,code = <0>; /* SW_LID */
|
|
label = "HED54XXU11 Hall Effect Sensor";
|
|
};
|
|
};
|
|
|
|
soc {
|
|
i2c@80004000 {
|
|
tc35893@44 {
|
|
compatible = "toshiba,tc35893";
|
|
reg = <0x44>;
|
|
interrupt-parent = <&gpio6>;
|
|
interrupts = <26 IRQ_TYPE_EDGE_RISING>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&tc35893_tvk_mode>;
|
|
|
|
interrupt-controller;
|
|
#interrupt-cells = <1>;
|
|
status = "disabled";
|
|
|
|
tc3589x_gpio {
|
|
compatible = "toshiba,tc3589x-gpio";
|
|
interrupts = <0>;
|
|
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
};
|
|
tc3589x_keypad {
|
|
compatible = "toshiba,tc3589x-keypad";
|
|
interrupts = <6>;
|
|
debounce-delay-ms = <4>;
|
|
keypad,num-columns = <8>;
|
|
keypad,num-rows = <8>;
|
|
linux,no-autorepeat;
|
|
wakeup-source;
|
|
linux,keymap = <MATRIX_KEY(3, 1, KEY_END)>,
|
|
<MATRIX_KEY(4, 1, KEY_HOME)>,
|
|
<MATRIX_KEY(6, 4, KEY_VOLUMEDOWN)>,
|
|
<MATRIX_KEY(4, 2, KEY_EMAIL)>,
|
|
<MATRIX_KEY(3, 3, KEY_RIGHT)>,
|
|
<MATRIX_KEY(2, 5, KEY_BACKSPACE)>,
|
|
<MATRIX_KEY(6, 7, KEY_MENU)>,
|
|
<MATRIX_KEY(5, 0, KEY_ENTER)>,
|
|
<MATRIX_KEY(4, 3, KEY_0)>,
|
|
<MATRIX_KEY(3, 4, KEY_DOT)>,
|
|
<MATRIX_KEY(5, 2, KEY_UP)>,
|
|
<MATRIX_KEY(3, 5, KEY_DOWN)>,
|
|
<MATRIX_KEY(4, 5, KEY_SEND)>,
|
|
<MATRIX_KEY(0, 5, KEY_BACK)>,
|
|
<MATRIX_KEY(6, 2, KEY_VOLUMEUP)>,
|
|
<MATRIX_KEY(1, 3, KEY_SPACE)>,
|
|
<MATRIX_KEY(7, 6, KEY_LEFT)>,
|
|
<MATRIX_KEY(5, 5, KEY_SEARCH)>;
|
|
};
|
|
};
|
|
};
|
|
|
|
i2c@80128000 {
|
|
accelerometer@18 {
|
|
/* Accelerometer */
|
|
compatible = "st,lsm303dlh-accel";
|
|
st,drdy-int-pin = <1>;
|
|
drive-open-drain;
|
|
reg = <0x18>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
vddio-supply = <&db8500_vsmps2_reg>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&accel_tvk_mode>;
|
|
/*
|
|
* These interrupts cannot be used: the other component
|
|
* ST-Micro L3D4200D gyro that is connected to the same lines
|
|
* cannot set its DRDY line to open drain, so it cannot be
|
|
* shared with other peripherals. The should be defined for
|
|
* the falling edge if they could be wired together.
|
|
*
|
|
* interrupts-extended =
|
|
* <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
|
|
* <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
|
|
*/
|
|
};
|
|
magnetometer@1e {
|
|
/* Magnetometer */
|
|
compatible = "st,lsm303dlh-magn";
|
|
reg = <0x1e>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
vddio-supply = <&db8500_vsmps2_reg>;
|
|
/*
|
|
* These interrupts cannot be used: the other component
|
|
* ST-Micro L3D4200D gyro that is connected to the same lines
|
|
* cannot set its DRDY line to open drain, so it cannot be
|
|
* shared with other peripherals. The should be defined for
|
|
* the falling edge if they could be wired together.
|
|
*
|
|
* interrupts-extended =
|
|
* <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
|
|
* <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
|
|
*/
|
|
};
|
|
accelerometer@1c {
|
|
/* Accelerometer */
|
|
compatible = "st,lis331dl-accel";
|
|
st,drdy-int-pin = <1>;
|
|
reg = <0x1c>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
vddio-supply = <&db8500_vsmps2_reg>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&accel_tvk_mode>;
|
|
interrupt-parent = <&gpio2>;
|
|
/* INT2 would need to be open drain */
|
|
interrupts = <18 IRQ_TYPE_EDGE_RISING>,
|
|
<19 IRQ_TYPE_EDGE_RISING>;
|
|
};
|
|
magnetometer@f {
|
|
/* Magnetometer */
|
|
compatible = "asahi-kasei,ak8974";
|
|
reg = <0x0f>;
|
|
avdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
dvdd-supply = <&db8500_vsmps2_reg>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&gyro_magn_tvk_mode>;
|
|
/*
|
|
* These interrupts cannot be used: the other component
|
|
* ST-Micro L3D4200D gyro that is connected to the same lines
|
|
* cannot set its DRDY line to open drain, so it cannot be
|
|
* shared with other peripherals. The should be defined for
|
|
* the falling edge if they could be wired together.
|
|
*
|
|
* interrupts-extended =
|
|
* <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
|
|
* <&gpio0 31 IRQ_TYPE_EDGE_FALLING>;
|
|
*/
|
|
};
|
|
gyroscope@68 {
|
|
/* Gyroscope */
|
|
compatible = "st,l3g4200d-gyro";
|
|
st,drdy-int-pin = <2>;
|
|
reg = <0x68>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
vddio-supply = <&db8500_vsmps2_reg>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&gyro_magn_tvk_mode>;
|
|
interrupts-extended =
|
|
<&gpio1 0 IRQ_TYPE_EDGE_RISING>,
|
|
<&gpio0 31 IRQ_TYPE_EDGE_RISING>;
|
|
};
|
|
pressure@5c {
|
|
/* Barometer/pressure sensor */
|
|
compatible = "st,lps001wp-press";
|
|
reg = <0x5c>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
vddio-supply = <&db8500_vsmps2_reg>;
|
|
};
|
|
};
|
|
i2c@80110000 {
|
|
synaptics@4b {
|
|
/* Synaptics RMI4 TM1217 touchscreen */
|
|
compatible = "syna,rmi4-i2c";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0x4b>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
vddio-supply = <&db8500_vsmps2_reg>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&synaptics_tvk_mode>;
|
|
interrupt-parent = <&gpio2>;
|
|
interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
|
|
|
|
rmi4-f01@1 {
|
|
reg = <0x1>;
|
|
syna,nosleep = <1>;
|
|
};
|
|
rmi4-f11@11 {
|
|
reg = <0x11>;
|
|
syna,sensor-type = <1>;
|
|
/* This is a landscape display */
|
|
touchscreen-swapped-x-y;
|
|
};
|
|
};
|
|
};
|
|
mcde@a0350000 {
|
|
status = "okay";
|
|
|
|
dsi@a0351000 {
|
|
panel {
|
|
compatible = "samsung,s6d16d0";
|
|
reg = <0>;
|
|
vdd1-supply = <&ab8500_ldo_aux1_reg>;
|
|
reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
pinctrl {
|
|
prox {
|
|
prox_tvk_mode: prox_tvk {
|
|
tvk_cfg {
|
|
pins = "GPIO217_AH12";
|
|
ste,config = <&gpio_in_pu>;
|
|
};
|
|
};
|
|
};
|
|
hall {
|
|
hall_tvk_mode: hall_tvk {
|
|
tvk_cfg {
|
|
pins = "GPIO145_C13";
|
|
ste,config = <&gpio_in_pu>;
|
|
};
|
|
};
|
|
};
|
|
tc35893 {
|
|
/* IRQ from the TC35893 */
|
|
tc35893_tvk_mode: tc35893_tvk {
|
|
tvk_cfg {
|
|
pins = "GPIO218_AH11";
|
|
ste,config = <&gpio_in_pu>;
|
|
};
|
|
};
|
|
};
|
|
accelerometer {
|
|
accel_tvk_mode: accel_tvk {
|
|
/* Accelerometer interrupt lines 1 & 2 */
|
|
tvk_cfg {
|
|
pins = "GPIO82_C1", "GPIO83_D3";
|
|
ste,config = <&gpio_in_pd>;
|
|
};
|
|
};
|
|
};
|
|
gyroscope {
|
|
/*
|
|
* These lines are shared between Gyroscope l3g400dh
|
|
* and AK8974 magnetometer.
|
|
*/
|
|
gyro_magn_tvk_mode: gyro_magn_tvk {
|
|
/* GPIO 31 used for INT pull down the line */
|
|
tvk_cfg1 {
|
|
pins = "GPIO31_V3";
|
|
ste,config = <&gpio_in_pd>;
|
|
};
|
|
/* GPIO 32 used for DRDY, pull this down */
|
|
tvk_cfg2 {
|
|
pins = "GPIO32_V2";
|
|
ste,config = <&gpio_in_pd>;
|
|
};
|
|
};
|
|
};
|
|
synaptics {
|
|
synaptics_tvk_mode: synaptics_tvk {
|
|
/* Touchscreen uses GPIO 84 */
|
|
tvk_cfg1 {
|
|
pins = "GPIO84_C2";
|
|
ste,config = <&gpio_in_pu>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|