e34d65696d
The DSA driver needs to be passed a reference to an mdio bus. Typically the mac is configured to use a fixed link but the mdio bus still needs to be registered so that it con configure the switch. This patch follows the same process as the altera tse ethernet driver for creation of the mdio bus. Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Phil Reid <preid@electromag.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
77 lines
3.2 KiB
Plaintext
77 lines
3.2 KiB
Plaintext
* STMicroelectronics 10/100/1000 Ethernet driver (GMAC)
|
|
|
|
Required properties:
|
|
- compatible: Should be "snps,dwmac-<ip_version>" "snps,dwmac"
|
|
For backwards compatibility: "st,spear600-gmac" is also supported.
|
|
- reg: Address and length of the register set for the device
|
|
- interrupt-parent: Should be the phandle for the interrupt controller
|
|
that services interrupts for this device
|
|
- interrupts: Should contain the STMMAC interrupts
|
|
- interrupt-names: Should contain the interrupt names "macirq"
|
|
"eth_wake_irq" if this interrupt is supported in the "interrupts"
|
|
property
|
|
- phy-mode: See ethernet.txt file in the same directory.
|
|
- snps,reset-gpio gpio number for phy reset.
|
|
- snps,reset-active-low boolean flag to indicate if phy reset is active low.
|
|
- snps,reset-delays-us is triplet of delays
|
|
The 1st cell is reset pre-delay in micro seconds.
|
|
The 2nd cell is reset pulse in micro seconds.
|
|
The 3rd cell is reset post-delay in micro seconds.
|
|
- snps,pbl Programmable Burst Length
|
|
- snps,fixed-burst Program the DMA to use the fixed burst mode
|
|
- snps,mixed-burst Program the DMA to use the mixed burst mode
|
|
- snps,force_thresh_dma_mode Force DMA to use the threshold mode for
|
|
both tx and rx
|
|
- snps,force_sf_dma_mode Force DMA to use the Store and Forward
|
|
mode for both tx and rx. This flag is
|
|
ignored if force_thresh_dma_mode is set.
|
|
- snps,multicast-filter-bins: Number of multicast filter hash bins
|
|
supported by this device instance
|
|
- snps,perfect-filter-entries: Number of perfect filter entries supported
|
|
by this device instance
|
|
|
|
Optional properties:
|
|
- resets: Should contain a phandle to the STMMAC reset signal, if any
|
|
- reset-names: Should contain the reset signal name "stmmaceth", if a
|
|
reset phandle is given
|
|
- max-frame-size: See ethernet.txt file in the same directory
|
|
- clocks: If present, the first clock should be the GMAC main clock and
|
|
the second clock should be peripheral's register interface clock. Further
|
|
clocks may be specified in derived bindings.
|
|
- clock-names: One name for each entry in the clocks property, the
|
|
first one should be "stmmaceth" and the second one should be "pclk".
|
|
- clk_ptp_ref: this is the PTP reference clock; in case of the PTP is
|
|
available this clock is used for programming the Timestamp Addend Register.
|
|
If not passed then the system clock will be used and this is fine on some
|
|
platforms.
|
|
- snps,burst_len: The AXI burst lenth value of the AXI BUS MODE register.
|
|
- tx-fifo-depth: See ethernet.txt file in the same directory
|
|
- rx-fifo-depth: See ethernet.txt file in the same directory
|
|
- mdio: with compatible = "snps,dwmac-mdio", create and register mdio bus.
|
|
|
|
Examples:
|
|
|
|
gmac0: ethernet@e0800000 {
|
|
compatible = "st,spear600-gmac";
|
|
reg = <0xe0800000 0x8000>;
|
|
interrupt-parent = <&vic1>;
|
|
interrupts = <24 23>;
|
|
interrupt-names = "macirq", "eth_wake_irq";
|
|
mac-address = [000000000000]; /* Filled in by U-Boot */
|
|
max-frame-size = <3800>;
|
|
phy-mode = "gmii";
|
|
snps,multicast-filter-bins = <256>;
|
|
snps,perfect-filter-entries = <128>;
|
|
rx-fifo-depth = <16384>;
|
|
tx-fifo-depth = <16384>;
|
|
clocks = <&clock>;
|
|
clock-names = "stmmaceth";
|
|
mdio0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "snps,dwmac-mdio";
|
|
phy1: ethernet-phy@0 {
|
|
};
|
|
};
|
|
};
|