4553474d97
In case timers are not in sync when cpus start (i.e. hot plug / offset resets) we need to synchronize the secondary cpus internal timer with the main cpu. This is needed as in OpenRISC SMP there is only one clocksource registered which reads from the same ttcr register on each cpu. This synchronization routine heavily borrows from mips implementation that does something similar. Signed-off-by: Stafford Horne <shorne@gmail.com>
121 lines
2.9 KiB
C
121 lines
2.9 KiB
C
/*
|
|
* OR1K timer synchronisation
|
|
*
|
|
* Based on work from MIPS implementation.
|
|
*
|
|
* All CPUs will have their count registers synchronised to the CPU0 next time
|
|
* value. This can cause a small timewarp for CPU0. All other CPU's should
|
|
* not have done anything significant (but they may have had interrupts
|
|
* enabled briefly - prom_smp_finish() should not be responsible for enabling
|
|
* interrupts...)
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/irqflags.h>
|
|
#include <linux/cpumask.h>
|
|
|
|
#include <asm/time.h>
|
|
#include <asm/timex.h>
|
|
#include <linux/atomic.h>
|
|
#include <asm/barrier.h>
|
|
|
|
#include <asm/spr.h>
|
|
|
|
static unsigned int initcount;
|
|
static atomic_t count_count_start = ATOMIC_INIT(0);
|
|
static atomic_t count_count_stop = ATOMIC_INIT(0);
|
|
|
|
#define COUNTON 100
|
|
#define NR_LOOPS 3
|
|
|
|
void synchronise_count_master(int cpu)
|
|
{
|
|
int i;
|
|
unsigned long flags;
|
|
|
|
pr_info("Synchronize counters for CPU %u: ", cpu);
|
|
|
|
local_irq_save(flags);
|
|
|
|
/*
|
|
* We loop a few times to get a primed instruction cache,
|
|
* then the last pass is more or less synchronised and
|
|
* the master and slaves each set their cycle counters to a known
|
|
* value all at once. This reduces the chance of having random offsets
|
|
* between the processors, and guarantees that the maximum
|
|
* delay between the cycle counters is never bigger than
|
|
* the latency of information-passing (cachelines) between
|
|
* two CPUs.
|
|
*/
|
|
|
|
for (i = 0; i < NR_LOOPS; i++) {
|
|
/* slaves loop on '!= 2' */
|
|
while (atomic_read(&count_count_start) != 1)
|
|
mb();
|
|
atomic_set(&count_count_stop, 0);
|
|
smp_wmb();
|
|
|
|
/* Let the slave writes its count register */
|
|
atomic_inc(&count_count_start);
|
|
|
|
/* Count will be initialised to current timer */
|
|
if (i == 1)
|
|
initcount = get_cycles();
|
|
|
|
/*
|
|
* Everyone initialises count in the last loop:
|
|
*/
|
|
if (i == NR_LOOPS-1)
|
|
openrisc_timer_set(initcount);
|
|
|
|
/*
|
|
* Wait for slave to leave the synchronization point:
|
|
*/
|
|
while (atomic_read(&count_count_stop) != 1)
|
|
mb();
|
|
atomic_set(&count_count_start, 0);
|
|
smp_wmb();
|
|
atomic_inc(&count_count_stop);
|
|
}
|
|
/* Arrange for an interrupt in a short while */
|
|
openrisc_timer_set_next(COUNTON);
|
|
|
|
local_irq_restore(flags);
|
|
|
|
/*
|
|
* i386 code reported the skew here, but the
|
|
* count registers were almost certainly out of sync
|
|
* so no point in alarming people
|
|
*/
|
|
pr_cont("done.\n");
|
|
}
|
|
|
|
void synchronise_count_slave(int cpu)
|
|
{
|
|
int i;
|
|
|
|
/*
|
|
* Not every cpu is online at the time this gets called,
|
|
* so we first wait for the master to say everyone is ready
|
|
*/
|
|
|
|
for (i = 0; i < NR_LOOPS; i++) {
|
|
atomic_inc(&count_count_start);
|
|
while (atomic_read(&count_count_start) != 2)
|
|
mb();
|
|
|
|
/*
|
|
* Everyone initialises count in the last loop:
|
|
*/
|
|
if (i == NR_LOOPS-1)
|
|
openrisc_timer_set(initcount);
|
|
|
|
atomic_inc(&count_count_stop);
|
|
while (atomic_read(&count_count_stop) != 2)
|
|
mb();
|
|
}
|
|
/* Arrange for an interrupt in a short while */
|
|
openrisc_timer_set_next(COUNTON);
|
|
}
|
|
#undef NR_LOOPS
|