d85339d9ea
As previously reported by Sudip Mukherjee for the Samsung driver, the omap2 onenand driver is called omap2.c in our directory and omap2.c in the tty/serial/ directory. If both drivers are compiled as modules, it would produce the following warning: warning: same module names found: drivers/tty/serial/omap2.ko drivers/mtd/nand/onenand/omap2.ko Rename the onenand omap2 driver so that it fits the folder's convention: onenand_omap2.c. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
621 lines
15 KiB
C
621 lines
15 KiB
C
// SPDX-License-Identifier: GPL-2.0-only
|
|
/*
|
|
* OneNAND driver for OMAP2 / OMAP3
|
|
*
|
|
* Copyright © 2005-2006 Nokia Corporation
|
|
*
|
|
* Author: Jarkko Lavinen <jarkko.lavinen@nokia.com> and Juha Yrjölä
|
|
* IRQ and DMA support written by Timo Teras
|
|
*/
|
|
|
|
#include <linux/device.h>
|
|
#include <linux/module.h>
|
|
#include <linux/mtd/mtd.h>
|
|
#include <linux/mtd/onenand.h>
|
|
#include <linux/mtd/partitions.h>
|
|
#include <linux/of_device.h>
|
|
#include <linux/omap-gpmc.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/dma-mapping.h>
|
|
#include <linux/dmaengine.h>
|
|
#include <linux/io.h>
|
|
#include <linux/slab.h>
|
|
#include <linux/gpio/consumer.h>
|
|
|
|
#include <asm/mach/flash.h>
|
|
|
|
#define DRIVER_NAME "omap2-onenand"
|
|
|
|
#define ONENAND_BUFRAM_SIZE (1024 * 5)
|
|
|
|
struct omap2_onenand {
|
|
struct platform_device *pdev;
|
|
int gpmc_cs;
|
|
unsigned long phys_base;
|
|
struct gpio_desc *int_gpiod;
|
|
struct mtd_info mtd;
|
|
struct onenand_chip onenand;
|
|
struct completion irq_done;
|
|
struct completion dma_done;
|
|
struct dma_chan *dma_chan;
|
|
};
|
|
|
|
static void omap2_onenand_dma_complete_func(void *completion)
|
|
{
|
|
complete(completion);
|
|
}
|
|
|
|
static irqreturn_t omap2_onenand_interrupt(int irq, void *dev_id)
|
|
{
|
|
struct omap2_onenand *c = dev_id;
|
|
|
|
complete(&c->irq_done);
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static inline unsigned short read_reg(struct omap2_onenand *c, int reg)
|
|
{
|
|
return readw(c->onenand.base + reg);
|
|
}
|
|
|
|
static inline void write_reg(struct omap2_onenand *c, unsigned short value,
|
|
int reg)
|
|
{
|
|
writew(value, c->onenand.base + reg);
|
|
}
|
|
|
|
static int omap2_onenand_set_cfg(struct omap2_onenand *c,
|
|
bool sr, bool sw,
|
|
int latency, int burst_len)
|
|
{
|
|
unsigned short reg = ONENAND_SYS_CFG1_RDY | ONENAND_SYS_CFG1_INT;
|
|
|
|
reg |= latency << ONENAND_SYS_CFG1_BRL_SHIFT;
|
|
|
|
switch (burst_len) {
|
|
case 0: /* continuous */
|
|
break;
|
|
case 4:
|
|
reg |= ONENAND_SYS_CFG1_BL_4;
|
|
break;
|
|
case 8:
|
|
reg |= ONENAND_SYS_CFG1_BL_8;
|
|
break;
|
|
case 16:
|
|
reg |= ONENAND_SYS_CFG1_BL_16;
|
|
break;
|
|
case 32:
|
|
reg |= ONENAND_SYS_CFG1_BL_32;
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (latency > 5)
|
|
reg |= ONENAND_SYS_CFG1_HF;
|
|
if (latency > 7)
|
|
reg |= ONENAND_SYS_CFG1_VHF;
|
|
if (sr)
|
|
reg |= ONENAND_SYS_CFG1_SYNC_READ;
|
|
if (sw)
|
|
reg |= ONENAND_SYS_CFG1_SYNC_WRITE;
|
|
|
|
write_reg(c, reg, ONENAND_REG_SYS_CFG1);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int omap2_onenand_get_freq(int ver)
|
|
{
|
|
switch ((ver >> 4) & 0xf) {
|
|
case 0:
|
|
return 40;
|
|
case 1:
|
|
return 54;
|
|
case 2:
|
|
return 66;
|
|
case 3:
|
|
return 83;
|
|
case 4:
|
|
return 104;
|
|
}
|
|
|
|
return -EINVAL;
|
|
}
|
|
|
|
static void wait_err(char *msg, int state, unsigned int ctrl, unsigned int intr)
|
|
{
|
|
printk(KERN_ERR "onenand_wait: %s! state %d ctrl 0x%04x intr 0x%04x\n",
|
|
msg, state, ctrl, intr);
|
|
}
|
|
|
|
static void wait_warn(char *msg, int state, unsigned int ctrl,
|
|
unsigned int intr)
|
|
{
|
|
printk(KERN_WARNING "onenand_wait: %s! state %d ctrl 0x%04x "
|
|
"intr 0x%04x\n", msg, state, ctrl, intr);
|
|
}
|
|
|
|
static int omap2_onenand_wait(struct mtd_info *mtd, int state)
|
|
{
|
|
struct omap2_onenand *c = container_of(mtd, struct omap2_onenand, mtd);
|
|
struct onenand_chip *this = mtd->priv;
|
|
unsigned int intr = 0;
|
|
unsigned int ctrl, ctrl_mask;
|
|
unsigned long timeout;
|
|
u32 syscfg;
|
|
|
|
if (state == FL_RESETTING || state == FL_PREPARING_ERASE ||
|
|
state == FL_VERIFYING_ERASE) {
|
|
int i = 21;
|
|
unsigned int intr_flags = ONENAND_INT_MASTER;
|
|
|
|
switch (state) {
|
|
case FL_RESETTING:
|
|
intr_flags |= ONENAND_INT_RESET;
|
|
break;
|
|
case FL_PREPARING_ERASE:
|
|
intr_flags |= ONENAND_INT_ERASE;
|
|
break;
|
|
case FL_VERIFYING_ERASE:
|
|
i = 101;
|
|
break;
|
|
}
|
|
|
|
while (--i) {
|
|
udelay(1);
|
|
intr = read_reg(c, ONENAND_REG_INTERRUPT);
|
|
if (intr & ONENAND_INT_MASTER)
|
|
break;
|
|
}
|
|
ctrl = read_reg(c, ONENAND_REG_CTRL_STATUS);
|
|
if (ctrl & ONENAND_CTRL_ERROR) {
|
|
wait_err("controller error", state, ctrl, intr);
|
|
return -EIO;
|
|
}
|
|
if ((intr & intr_flags) == intr_flags)
|
|
return 0;
|
|
/* Continue in wait for interrupt branch */
|
|
}
|
|
|
|
if (state != FL_READING) {
|
|
int result;
|
|
|
|
/* Turn interrupts on */
|
|
syscfg = read_reg(c, ONENAND_REG_SYS_CFG1);
|
|
if (!(syscfg & ONENAND_SYS_CFG1_IOBE)) {
|
|
syscfg |= ONENAND_SYS_CFG1_IOBE;
|
|
write_reg(c, syscfg, ONENAND_REG_SYS_CFG1);
|
|
/* Add a delay to let GPIO settle */
|
|
syscfg = read_reg(c, ONENAND_REG_SYS_CFG1);
|
|
}
|
|
|
|
reinit_completion(&c->irq_done);
|
|
result = gpiod_get_value(c->int_gpiod);
|
|
if (result < 0) {
|
|
ctrl = read_reg(c, ONENAND_REG_CTRL_STATUS);
|
|
intr = read_reg(c, ONENAND_REG_INTERRUPT);
|
|
wait_err("gpio error", state, ctrl, intr);
|
|
return result;
|
|
} else if (result == 0) {
|
|
int retry_cnt = 0;
|
|
retry:
|
|
if (!wait_for_completion_io_timeout(&c->irq_done,
|
|
msecs_to_jiffies(20))) {
|
|
/* Timeout after 20ms */
|
|
ctrl = read_reg(c, ONENAND_REG_CTRL_STATUS);
|
|
if (ctrl & ONENAND_CTRL_ONGO &&
|
|
!this->ongoing) {
|
|
/*
|
|
* The operation seems to be still going
|
|
* so give it some more time.
|
|
*/
|
|
retry_cnt += 1;
|
|
if (retry_cnt < 3)
|
|
goto retry;
|
|
intr = read_reg(c,
|
|
ONENAND_REG_INTERRUPT);
|
|
wait_err("timeout", state, ctrl, intr);
|
|
return -EIO;
|
|
}
|
|
intr = read_reg(c, ONENAND_REG_INTERRUPT);
|
|
if ((intr & ONENAND_INT_MASTER) == 0)
|
|
wait_warn("timeout", state, ctrl, intr);
|
|
}
|
|
}
|
|
} else {
|
|
int retry_cnt = 0;
|
|
|
|
/* Turn interrupts off */
|
|
syscfg = read_reg(c, ONENAND_REG_SYS_CFG1);
|
|
syscfg &= ~ONENAND_SYS_CFG1_IOBE;
|
|
write_reg(c, syscfg, ONENAND_REG_SYS_CFG1);
|
|
|
|
timeout = jiffies + msecs_to_jiffies(20);
|
|
while (1) {
|
|
if (time_before(jiffies, timeout)) {
|
|
intr = read_reg(c, ONENAND_REG_INTERRUPT);
|
|
if (intr & ONENAND_INT_MASTER)
|
|
break;
|
|
} else {
|
|
/* Timeout after 20ms */
|
|
ctrl = read_reg(c, ONENAND_REG_CTRL_STATUS);
|
|
if (ctrl & ONENAND_CTRL_ONGO) {
|
|
/*
|
|
* The operation seems to be still going
|
|
* so give it some more time.
|
|
*/
|
|
retry_cnt += 1;
|
|
if (retry_cnt < 3) {
|
|
timeout = jiffies +
|
|
msecs_to_jiffies(20);
|
|
continue;
|
|
}
|
|
}
|
|
break;
|
|
}
|
|
}
|
|
}
|
|
|
|
intr = read_reg(c, ONENAND_REG_INTERRUPT);
|
|
ctrl = read_reg(c, ONENAND_REG_CTRL_STATUS);
|
|
|
|
if (intr & ONENAND_INT_READ) {
|
|
int ecc = read_reg(c, ONENAND_REG_ECC_STATUS);
|
|
|
|
if (ecc) {
|
|
unsigned int addr1, addr8;
|
|
|
|
addr1 = read_reg(c, ONENAND_REG_START_ADDRESS1);
|
|
addr8 = read_reg(c, ONENAND_REG_START_ADDRESS8);
|
|
if (ecc & ONENAND_ECC_2BIT_ALL) {
|
|
printk(KERN_ERR "onenand_wait: ECC error = "
|
|
"0x%04x, addr1 %#x, addr8 %#x\n",
|
|
ecc, addr1, addr8);
|
|
mtd->ecc_stats.failed++;
|
|
return -EBADMSG;
|
|
} else if (ecc & ONENAND_ECC_1BIT_ALL) {
|
|
printk(KERN_NOTICE "onenand_wait: correctable "
|
|
"ECC error = 0x%04x, addr1 %#x, "
|
|
"addr8 %#x\n", ecc, addr1, addr8);
|
|
mtd->ecc_stats.corrected++;
|
|
}
|
|
}
|
|
} else if (state == FL_READING) {
|
|
wait_err("timeout", state, ctrl, intr);
|
|
return -EIO;
|
|
}
|
|
|
|
if (ctrl & ONENAND_CTRL_ERROR) {
|
|
wait_err("controller error", state, ctrl, intr);
|
|
if (ctrl & ONENAND_CTRL_LOCK)
|
|
printk(KERN_ERR "onenand_wait: "
|
|
"Device is write protected!!!\n");
|
|
return -EIO;
|
|
}
|
|
|
|
ctrl_mask = 0xFE9F;
|
|
if (this->ongoing)
|
|
ctrl_mask &= ~0x8000;
|
|
|
|
if (ctrl & ctrl_mask)
|
|
wait_warn("unexpected controller status", state, ctrl, intr);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static inline int omap2_onenand_bufferram_offset(struct mtd_info *mtd, int area)
|
|
{
|
|
struct onenand_chip *this = mtd->priv;
|
|
|
|
if (ONENAND_CURRENT_BUFFERRAM(this)) {
|
|
if (area == ONENAND_DATARAM)
|
|
return this->writesize;
|
|
if (area == ONENAND_SPARERAM)
|
|
return mtd->oobsize;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static inline int omap2_onenand_dma_transfer(struct omap2_onenand *c,
|
|
dma_addr_t src, dma_addr_t dst,
|
|
size_t count)
|
|
{
|
|
struct dma_async_tx_descriptor *tx;
|
|
dma_cookie_t cookie;
|
|
|
|
tx = dmaengine_prep_dma_memcpy(c->dma_chan, dst, src, count,
|
|
DMA_CTRL_ACK | DMA_PREP_INTERRUPT);
|
|
if (!tx) {
|
|
dev_err(&c->pdev->dev, "Failed to prepare DMA memcpy\n");
|
|
return -EIO;
|
|
}
|
|
|
|
reinit_completion(&c->dma_done);
|
|
|
|
tx->callback = omap2_onenand_dma_complete_func;
|
|
tx->callback_param = &c->dma_done;
|
|
|
|
cookie = tx->tx_submit(tx);
|
|
if (dma_submit_error(cookie)) {
|
|
dev_err(&c->pdev->dev, "Failed to do DMA tx_submit\n");
|
|
return -EIO;
|
|
}
|
|
|
|
dma_async_issue_pending(c->dma_chan);
|
|
|
|
if (!wait_for_completion_io_timeout(&c->dma_done,
|
|
msecs_to_jiffies(20))) {
|
|
dmaengine_terminate_sync(c->dma_chan);
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int omap2_onenand_read_bufferram(struct mtd_info *mtd, int area,
|
|
unsigned char *buffer, int offset,
|
|
size_t count)
|
|
{
|
|
struct omap2_onenand *c = container_of(mtd, struct omap2_onenand, mtd);
|
|
struct onenand_chip *this = mtd->priv;
|
|
struct device *dev = &c->pdev->dev;
|
|
void *buf = (void *)buffer;
|
|
dma_addr_t dma_src, dma_dst;
|
|
int bram_offset, err;
|
|
size_t xtra;
|
|
|
|
bram_offset = omap2_onenand_bufferram_offset(mtd, area) + area + offset;
|
|
/*
|
|
* If the buffer address is not DMA-able, len is not long enough to make
|
|
* DMA transfers profitable or panic_write() may be in an interrupt
|
|
* context fallback to PIO mode.
|
|
*/
|
|
if (!virt_addr_valid(buf) || bram_offset & 3 || (size_t)buf & 3 ||
|
|
count < 384 || in_interrupt() || oops_in_progress)
|
|
goto out_copy;
|
|
|
|
xtra = count & 3;
|
|
if (xtra) {
|
|
count -= xtra;
|
|
memcpy(buf + count, this->base + bram_offset + count, xtra);
|
|
}
|
|
|
|
dma_dst = dma_map_single(dev, buf, count, DMA_FROM_DEVICE);
|
|
dma_src = c->phys_base + bram_offset;
|
|
|
|
if (dma_mapping_error(dev, dma_dst)) {
|
|
dev_err(dev, "Couldn't DMA map a %d byte buffer\n", count);
|
|
goto out_copy;
|
|
}
|
|
|
|
err = omap2_onenand_dma_transfer(c, dma_src, dma_dst, count);
|
|
dma_unmap_single(dev, dma_dst, count, DMA_FROM_DEVICE);
|
|
if (!err)
|
|
return 0;
|
|
|
|
dev_err(dev, "timeout waiting for DMA\n");
|
|
|
|
out_copy:
|
|
memcpy(buf, this->base + bram_offset, count);
|
|
return 0;
|
|
}
|
|
|
|
static int omap2_onenand_write_bufferram(struct mtd_info *mtd, int area,
|
|
const unsigned char *buffer,
|
|
int offset, size_t count)
|
|
{
|
|
struct omap2_onenand *c = container_of(mtd, struct omap2_onenand, mtd);
|
|
struct onenand_chip *this = mtd->priv;
|
|
struct device *dev = &c->pdev->dev;
|
|
void *buf = (void *)buffer;
|
|
dma_addr_t dma_src, dma_dst;
|
|
int bram_offset, err;
|
|
|
|
bram_offset = omap2_onenand_bufferram_offset(mtd, area) + area + offset;
|
|
/*
|
|
* If the buffer address is not DMA-able, len is not long enough to make
|
|
* DMA transfers profitable or panic_write() may be in an interrupt
|
|
* context fallback to PIO mode.
|
|
*/
|
|
if (!virt_addr_valid(buf) || bram_offset & 3 || (size_t)buf & 3 ||
|
|
count < 384 || in_interrupt() || oops_in_progress)
|
|
goto out_copy;
|
|
|
|
dma_src = dma_map_single(dev, buf, count, DMA_TO_DEVICE);
|
|
dma_dst = c->phys_base + bram_offset;
|
|
if (dma_mapping_error(dev, dma_src)) {
|
|
dev_err(dev, "Couldn't DMA map a %d byte buffer\n", count);
|
|
goto out_copy;
|
|
}
|
|
|
|
err = omap2_onenand_dma_transfer(c, dma_src, dma_dst, count);
|
|
dma_unmap_page(dev, dma_src, count, DMA_TO_DEVICE);
|
|
if (!err)
|
|
return 0;
|
|
|
|
dev_err(dev, "timeout waiting for DMA\n");
|
|
|
|
out_copy:
|
|
memcpy(this->base + bram_offset, buf, count);
|
|
return 0;
|
|
}
|
|
|
|
static void omap2_onenand_shutdown(struct platform_device *pdev)
|
|
{
|
|
struct omap2_onenand *c = dev_get_drvdata(&pdev->dev);
|
|
|
|
/* With certain content in the buffer RAM, the OMAP boot ROM code
|
|
* can recognize the flash chip incorrectly. Zero it out before
|
|
* soft reset.
|
|
*/
|
|
memset((__force void *)c->onenand.base, 0, ONENAND_BUFRAM_SIZE);
|
|
}
|
|
|
|
static int omap2_onenand_probe(struct platform_device *pdev)
|
|
{
|
|
u32 val;
|
|
dma_cap_mask_t mask;
|
|
int freq, latency, r;
|
|
struct resource *res;
|
|
struct omap2_onenand *c;
|
|
struct gpmc_onenand_info info;
|
|
struct device *dev = &pdev->dev;
|
|
struct device_node *np = dev->of_node;
|
|
|
|
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
|
if (!res) {
|
|
dev_err(dev, "error getting memory resource\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
r = of_property_read_u32(np, "reg", &val);
|
|
if (r) {
|
|
dev_err(dev, "reg not found in DT\n");
|
|
return r;
|
|
}
|
|
|
|
c = devm_kzalloc(dev, sizeof(struct omap2_onenand), GFP_KERNEL);
|
|
if (!c)
|
|
return -ENOMEM;
|
|
|
|
init_completion(&c->irq_done);
|
|
init_completion(&c->dma_done);
|
|
c->gpmc_cs = val;
|
|
c->phys_base = res->start;
|
|
|
|
c->onenand.base = devm_ioremap_resource(dev, res);
|
|
if (IS_ERR(c->onenand.base))
|
|
return PTR_ERR(c->onenand.base);
|
|
|
|
c->int_gpiod = devm_gpiod_get_optional(dev, "int", GPIOD_IN);
|
|
if (IS_ERR(c->int_gpiod)) {
|
|
r = PTR_ERR(c->int_gpiod);
|
|
/* Just try again if this happens */
|
|
if (r != -EPROBE_DEFER)
|
|
dev_err(dev, "error getting gpio: %d\n", r);
|
|
return r;
|
|
}
|
|
|
|
if (c->int_gpiod) {
|
|
r = devm_request_irq(dev, gpiod_to_irq(c->int_gpiod),
|
|
omap2_onenand_interrupt,
|
|
IRQF_TRIGGER_RISING, "onenand", c);
|
|
if (r)
|
|
return r;
|
|
|
|
c->onenand.wait = omap2_onenand_wait;
|
|
}
|
|
|
|
dma_cap_zero(mask);
|
|
dma_cap_set(DMA_MEMCPY, mask);
|
|
|
|
c->dma_chan = dma_request_channel(mask, NULL, NULL);
|
|
if (c->dma_chan) {
|
|
c->onenand.read_bufferram = omap2_onenand_read_bufferram;
|
|
c->onenand.write_bufferram = omap2_onenand_write_bufferram;
|
|
}
|
|
|
|
c->pdev = pdev;
|
|
c->mtd.priv = &c->onenand;
|
|
c->mtd.dev.parent = dev;
|
|
mtd_set_of_node(&c->mtd, dev->of_node);
|
|
|
|
dev_info(dev, "initializing on CS%d (0x%08lx), va %p, %s mode\n",
|
|
c->gpmc_cs, c->phys_base, c->onenand.base,
|
|
c->dma_chan ? "DMA" : "PIO");
|
|
|
|
r = onenand_scan(&c->mtd, 1);
|
|
if (r < 0)
|
|
goto err_release_dma;
|
|
|
|
freq = omap2_onenand_get_freq(c->onenand.version_id);
|
|
if (freq > 0) {
|
|
switch (freq) {
|
|
case 104:
|
|
latency = 7;
|
|
break;
|
|
case 83:
|
|
latency = 6;
|
|
break;
|
|
case 66:
|
|
latency = 5;
|
|
break;
|
|
case 56:
|
|
latency = 4;
|
|
break;
|
|
default: /* 40 MHz or lower */
|
|
latency = 3;
|
|
break;
|
|
}
|
|
|
|
r = gpmc_omap_onenand_set_timings(dev, c->gpmc_cs,
|
|
freq, latency, &info);
|
|
if (r)
|
|
goto err_release_onenand;
|
|
|
|
r = omap2_onenand_set_cfg(c, info.sync_read, info.sync_write,
|
|
latency, info.burst_len);
|
|
if (r)
|
|
goto err_release_onenand;
|
|
|
|
if (info.sync_read || info.sync_write)
|
|
dev_info(dev, "optimized timings for %d MHz\n", freq);
|
|
}
|
|
|
|
r = mtd_device_register(&c->mtd, NULL, 0);
|
|
if (r)
|
|
goto err_release_onenand;
|
|
|
|
platform_set_drvdata(pdev, c);
|
|
|
|
return 0;
|
|
|
|
err_release_onenand:
|
|
onenand_release(&c->mtd);
|
|
err_release_dma:
|
|
if (c->dma_chan)
|
|
dma_release_channel(c->dma_chan);
|
|
|
|
return r;
|
|
}
|
|
|
|
static int omap2_onenand_remove(struct platform_device *pdev)
|
|
{
|
|
struct omap2_onenand *c = dev_get_drvdata(&pdev->dev);
|
|
|
|
onenand_release(&c->mtd);
|
|
if (c->dma_chan)
|
|
dma_release_channel(c->dma_chan);
|
|
omap2_onenand_shutdown(pdev);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct of_device_id omap2_onenand_id_table[] = {
|
|
{ .compatible = "ti,omap2-onenand", },
|
|
{},
|
|
};
|
|
MODULE_DEVICE_TABLE(of, omap2_onenand_id_table);
|
|
|
|
static struct platform_driver omap2_onenand_driver = {
|
|
.probe = omap2_onenand_probe,
|
|
.remove = omap2_onenand_remove,
|
|
.shutdown = omap2_onenand_shutdown,
|
|
.driver = {
|
|
.name = DRIVER_NAME,
|
|
.of_match_table = omap2_onenand_id_table,
|
|
},
|
|
};
|
|
|
|
module_platform_driver(omap2_onenand_driver);
|
|
|
|
MODULE_ALIAS("platform:" DRIVER_NAME);
|
|
MODULE_LICENSE("GPL");
|
|
MODULE_AUTHOR("Jarkko Lavinen <jarkko.lavinen@nokia.com>");
|
|
MODULE_DESCRIPTION("Glue layer for OneNAND flash on OMAP2 / OMAP3");
|