mirror of
https://gitlab.com/libvirt/libvirt.git
synced 2024-12-23 21:34:54 +03:00
1787a77cf8
Signed-off-by: Tim Wiederhake <twiederh@redhat.com> Reviewed-by: Andrea Bolognani <abologna@redhat.com> Reviewed-by: Erik Skultety <eskultet@redhat.com>
152 lines
4.1 KiB
ReStructuredText
152 lines
4.1 KiB
ReStructuredText
==============
|
|
libvirt-guests
|
|
==============
|
|
|
|
-------------------------------------
|
|
suspend/resume running libvirt guests
|
|
-------------------------------------
|
|
|
|
:Manual section: 8
|
|
:Manual group: Virtualization Support
|
|
|
|
.. contents::
|
|
|
|
SYNOPSIS
|
|
========
|
|
|
|
``libvirt-guests`` *COMMAND*
|
|
|
|
|
|
DESCRIPTION
|
|
===========
|
|
|
|
``libvirt-guests`` is a service that can be used to coordinate guest and host
|
|
lifecycle actions. By default, ``libvirt-guests`` will suspend running guests
|
|
when the host shuts down, and restore them to their pre-shutdown state when
|
|
the host reboots.
|
|
|
|
``libvirt-guests`` is typically under control of systemd. When
|
|
``libvirt-guests.service`` is enabled, systemd will call ``libvirt-guests``
|
|
with the ``start`` *COMMAND* when the host boots. Conversely, systemd will call
|
|
``libvirt-guests`` with the ``stop`` *COMMAND* when the host shuts down.
|
|
|
|
``libvirt-guests`` can be used directly. In addition to the ``start`` and
|
|
``stop`` *COMMAND*\s, it also supports ``status``, ``restart``, ``condrestart``,
|
|
``try-restart``, ``reload``, ``force-reload``, ``gueststatus``, and
|
|
``shutdown`` *COMMAND*\s.
|
|
|
|
|
|
FILES
|
|
=====
|
|
|
|
``libvirt-guests`` defines several variables to control service behavior.
|
|
The default value of these variables can be overridden in:
|
|
|
|
* ``@SYSCONFDIR@/sysconfig/libvirt-guests``
|
|
|
|
The following variables are supported:
|
|
|
|
- URIS=default
|
|
|
|
URIs to check for running guests. Example:
|
|
``URIS='default xen:///system xen+tcp://host/system lxc:///system'``
|
|
|
|
- ON_BOOT=start
|
|
|
|
Action taken on host boot
|
|
|
|
* start
|
|
|
|
All guests which were running on shutdown are started on boot regardless
|
|
of their autostart settings
|
|
|
|
* ignore
|
|
|
|
``libvirt-guests`` won't start any guest on boot, however, guests marked
|
|
as autostart will still be automatically started by libvirtd
|
|
|
|
- START_DELAY=0
|
|
|
|
Number of seconds to wait between each guest start. Set to 0 to allow parallel
|
|
startup.
|
|
|
|
- ON_SHUTDOWN=suspend
|
|
|
|
Action taken on host shutdown
|
|
|
|
* suspend
|
|
|
|
All running guests are suspended using virsh managedsave
|
|
|
|
* shutdown
|
|
|
|
All running guests are asked to shutdown. Please be careful with this
|
|
settings since there is no way to distinguish between a guest which is
|
|
stuck or ignores shutdown requests and a guest which just needs a long
|
|
time to shutdown. When setting ON_SHUTDOWN=shutdown, you must also set
|
|
SHUTDOWN_TIMEOUT to a value suitable for your guests.
|
|
|
|
- PARALLEL_SHUTDOWN=0
|
|
|
|
Number of guests will be shutdown concurrently, taking effect when
|
|
"ON_SHUTDOWN" is set to "shutdown". If Set to 0, guests will be shutdown one
|
|
after another. Number of guests on shutdown at any time will not exceed number
|
|
set in this variable.
|
|
|
|
- SHUTDOWN_TIMEOUT=300
|
|
|
|
Number of seconds we're willing to wait for a guest to shut down. If parallel
|
|
shutdown is enabled, this timeout applies as a timeout for shutting down all
|
|
guests on a single URI defined in the variable URIS. If this is 0, then there
|
|
is no time out (use with caution, as guests might not respond to a shutdown
|
|
request). The default value is 300 seconds (5 minutes).
|
|
|
|
- BYPASS_CACHE=0
|
|
|
|
If non-zero, try to bypass the file system cache when saving and
|
|
restoring guests, even though this may give slower operation for
|
|
some file systems.
|
|
|
|
- SYNC_TIME=0
|
|
|
|
If non-zero, try to sync guest time on domain resume. Be aware, that
|
|
this requires guest agent with support for time synchronization
|
|
running in the guest. By default, this functionality is turned off.
|
|
|
|
|
|
BUGS
|
|
====
|
|
|
|
Please report all bugs you discover. This should be done via either:
|
|
|
|
#. the mailing list
|
|
|
|
`https://libvirt.org/contact.html <https://libvirt.org/contact.html>`_
|
|
|
|
#. the bug tracker
|
|
|
|
`https://libvirt.org/bugs.html <https://libvirt.org/bugs.html>`_
|
|
|
|
Alternatively, you may report bugs to your software distributor / vendor.
|
|
|
|
|
|
AUTHORS
|
|
=======
|
|
|
|
Please refer to the AUTHORS file distributed with libvirt.
|
|
|
|
|
|
LICENSE
|
|
=======
|
|
|
|
``libvirt-guests`` is distributed under the terms of the GNU LGPL v2.1+.
|
|
This is free software; see the source for copying conditions. There
|
|
is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR
|
|
PURPOSE
|
|
|
|
|
|
SEE ALSO
|
|
========
|
|
|
|
libvirtd(8), `https://libvirt.org/ <https://libvirt.org/>`_
|