mirror of
git://sourceware.org/git/lvm2.git
synced 2024-12-21 13:34:40 +03:00
udev: keep systemd vars on change event in 69-dm-lvm-metad.rules for systemd reload
The current logic that avoids setting SYSTEMD_ALIAS and SYSTEMD_WANTS on "change" events is flawed in the default "systemd background job" configuration. For systemd, it's important that device properties don't change spuriously. If an "add" event starts lvm2-pvscan@.service for a device, and a "change" event follows, removing SYSTEMD_ALIAS and SYSTEMD_WANTS from the udev db, information about unit dependencies between the device and the pvscan service can be lost in systemd, in particular if the daemon configuration is reloaded. Steps to reproduce problem: - create a device with an LVM PV - remove device - add device (generates "add" and "change" uevents for the device) (at this point SYSTEMD_ALIAS and SYSTEMD_WANTS are clear in udev db) - systemctl daemon-reload (systemd reloads udev db) - vgchange -a n - remove device => the lvm2-pvscan@.service for the device is still active although the device is gone. - add device again => the PV is not detected, because systemd sees the lvm2-pvscan@.service as active and thus doesn't restart it. The original purpose of this logic was to avoid volumes being scanned over and over again. With systemd background jobs, that isn't necessary, because systemd will not restart the job as long as it's active. Signed-off-by: Martin Wilck <mwilck@suse.com>
This commit is contained in:
Martin Wilck
Peter Rajnoha
parent
99bfbbf229
commit
7a7b8a7778
@ -1,5 +1,6 @@
|
||||
Version 2.02.178 -
|
||||
=====================================
|
||||
Keep systemd vars on change event in 69-dm-lvm-metad.rules for systemd reload.
|
||||
Write systemd and non-systemd rule in 69-dm-lvm-metad.rules, GOTO active one.
|
||||
Add test for activation/volume_list (Sub)LV remnants.
|
||||
Disallow usage of cache format 2 with mq cache policy.
|
||||
|
||||
@ -68,25 +68,15 @@ ACTION=="change", ENV{LVM_LOOP_PV_ACTIVATED}!="1", TEST=="loop/backing_file", EN
|
||||
ENV{LVM_LOOP_PV_ACTIVATED}!="1", ENV{SYSTEMD_READY}="0"
|
||||
GOTO="lvm_end"
|
||||
|
||||
# If the PV is not a special device listed above, scan only after device addition (ADD event)
|
||||
# If the PV is not a special device listed above, scan only if necessary.
|
||||
# For "direct_pvscan" mode (see below), this means run rules only an ADD events.
|
||||
# For "systemd_background" mode, systemd takes care of this by activating
|
||||
# the lvm2-pvscan@.service only once.
|
||||
LABEL="next"
|
||||
ACTION!="add", GOTO="lvm_end"
|
||||
ACTION!="(PVSCAN_ACTION)", GOTO="lvm_end"
|
||||
|
||||
LABEL="lvm_scan"
|
||||
|
||||
# The table below summarises the situations in which we reach the LABEL="lvm_scan".
|
||||
# Marked by X, X* means only if the special dev is properly set up.
|
||||
# The artificial ADD is supported for coldplugging. We avoid running the pvscan
|
||||
# on artificial CHANGE so there's no unexpected autoactivation when WATCH rule fires.
|
||||
# N.B. MD and loop never actually reaches lvm_scan on REMOVE as the PV label is gone
|
||||
# within a CHANGE event (these are caught by the "LVM_PV_GONE" rule at the beginning).
|
||||
#
|
||||
# | real ADD | real CHANGE | artificial ADD | artificial CHANGE | REMOVE
|
||||
# =============================================================================
|
||||
# DM | | X | X* | | X
|
||||
# MD | | X | X* | |
|
||||
# loop | | X | X* | |
|
||||
# other | X | | X | | X
|
||||
ENV{SYSTEMD_READY}="1"
|
||||
|
||||
# The method for invoking pvscan is selected at build time with the option
|
||||
@ -97,6 +87,27 @@ GOTO="(PVSCAN_RULE)"
|
||||
|
||||
LABEL="systemd_background"
|
||||
|
||||
# The table below summarises the situations in which we reach the LABEL="lvm_scan"
|
||||
# in the "systemd_background" case.
|
||||
# Marked by X, X* means only if the special dev is properly set up.
|
||||
# The artificial ADD is supported for coldplugging. We avoid running the pvscan
|
||||
# on artificial CHANGE so there's no unexpected autoactivation when WATCH rule fires.
|
||||
# N.B. MD and loop never actually reaches lvm_scan on REMOVE as the PV label is gone
|
||||
# within a CHANGE event (these are caught by the "LVM_PV_GONE" rule at the beginning).
|
||||
#
|
||||
# In this case, we simply set up the dependency between the device and the pvscan
|
||||
# job using SYSTEMD_ALIAS (which sets up a simplified device identifier that
|
||||
# allows using "BindsTo" in the sytemd unit file) and SYSTEMD_WANTS (which tells
|
||||
# systemd to start the pvscan job once the device is ready).
|
||||
# We need to set these variables for both "add" and "change" events, otherwise
|
||||
# systemd may loose information about the device/unit dependencies.
|
||||
#
|
||||
# | real ADD | real CHANGE | artificial ADD | artificial CHANGE | REMOVE
|
||||
# =============================================================================
|
||||
# DM | | X | X* | | X
|
||||
# MD | | X | X* | |
|
||||
# loop | | X | X* | |
|
||||
# other | X | X | X | | X
|
||||
ACTION!="remove", ENV{LVM_PV_GONE}=="1", RUN+="(BINDIR)/systemd-run (LVM_EXEC)/lvm pvscan --cache $major:$minor", GOTO="lvm_end"
|
||||
ENV{SYSTEMD_ALIAS}="/dev/block/$major:$minor"
|
||||
ENV{ID_MODEL}="LVM PV $env{ID_FS_UUID_ENC} on /dev/$name"
|
||||
@ -105,6 +116,21 @@ GOTO="lvm_end"
|
||||
|
||||
LABEL="direct_pvscan"
|
||||
|
||||
# The table below summarises the situations in which we reach the LABEL="lvm_scan"
|
||||
# for the "direct_pvscan" case.
|
||||
# Marked by X, X* means only if the special dev is properly set up.
|
||||
# The artificial ADD is supported for coldplugging. We avoid running the pvscan
|
||||
# on artificial CHANGE so there's no unexpected autoactivation when WATCH rule fires.
|
||||
#
|
||||
# In this case, we need to make sure that pvscan is not invoked spuriously, therefore
|
||||
# we invoke it only for "add" events for "other" devices.
|
||||
#
|
||||
# | real ADD | real CHANGE | artificial ADD | artificial CHANGE | REMOVE
|
||||
# =============================================================================
|
||||
# DM | | X | X* | | X
|
||||
# MD | | X | X* | |
|
||||
# loop | | X | X* | |
|
||||
# other | X | | X | | X
|
||||
RUN+="(LVM_EXEC)/lvm pvscan --background --cache --activate ay --major $major --minor $minor", ENV{LVM_SCANNED}="1"
|
||||
|
||||
LABEL="lvm_end"
|
||||
|
||||
@ -48,12 +48,14 @@ endif
|
||||
|
||||
ifeq ("@UDEV_SYSTEMD_BACKGROUND_JOBS@", "yes")
|
||||
PVSCAN_RULE=systemd_background
|
||||
PVSCAN_ACTION=add|change
|
||||
else
|
||||
PVSCAN_RULE=direct_pvscan
|
||||
PVSCAN_ACTION=add
|
||||
endif
|
||||
|
||||
%.rules: $(srcdir)/%.rules.in
|
||||
$(SED) -e "s+(DM_DIR)+$(DM_DIR)+;s+(BINDIR)+$(BINDIR)+;s+(BLKID_RULE)+$(BLKID_RULE)+;s+(PVSCAN_RULE)+$(PVSCAN_RULE)+;s+(DM_EXEC_RULE)+$(DM_EXEC_RULE)+;s+(DM_EXEC)+$(DM_EXEC)+;s+(LVM_EXEC_RULE)+$(LVM_EXEC_RULE)+;s+(LVM_EXEC)+$(LVM_EXEC)+;" $< >$@
|
||||
$(SED) -e "s+(DM_DIR)+$(DM_DIR)+;s+(BINDIR)+$(BINDIR)+;s+(BLKID_RULE)+$(BLKID_RULE)+;s+(PVSCAN_RULE)+$(PVSCAN_RULE)+;s+(PVSCAN_ACTION)+$(PVSCAN_ACTION)+;s+(DM_EXEC_RULE)+$(DM_EXEC_RULE)+;s+(DM_EXEC)+$(DM_EXEC)+;s+(LVM_EXEC_RULE)+$(LVM_EXEC_RULE)+;s+(LVM_EXEC)+$(LVM_EXEC)+;" $< >$@
|
||||
|
||||
%_install: %.rules
|
||||
$(INSTALL_DATA) -D $< $(udevdir)/$(<F)
|
||||
|
||||
Loading…
Reference in New Issue
Block a user