IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
A global flag in lvmetad indicates it has been disabled.
Other flags indicate the reason it was disabled.
These flags can be queried using get_global_info.
The lvmetactl debugging utility can set and clear the
disabled flag in lvmetad. Nothing else sets the
disabled flag yet.
Commands will check these flags after connecting to
lvmetad. If the disabled flag is set, the command
will not use the lvmetad cache, but revert to disk
scanning.
To test this feature:
$ lvmetactl get_global_info
response = "OK"
global_invalid = 0
global_disable = 0
disable_reason = "none"
token = "filter:3041577944"
$ vgs
(should report VGs from lvmetad)
$ lvmetactl set_global_disable 1
$ lvmetactl get_global_info
response = "OK"
global_invalid = 0
global_disable = 1
disable_reason = "DIRECT"
token = "filter:3041577944"
$ vgs
WARNING: Not using lvmetad because the disable flag was set directly.
(should report VGs without contacting lvmetad)
$ lvmetactl set_global_disable 0
$ vgs
(should report VGs from lvmetad)
Move checking the lvmetad state, and the possible rescan,
out of lvmetad_send() to the start of the command.
Previously, the token mismatch and rescan would occur
within lvmetad_send() for some other request. Now,
the token mismatch is detected earlier, so the
rescan can be done before the main command is in
progress. Rescanning deep within the processing of
another command will disturb the lvmcache state of
that other command.
A rescan already exists at the start of the command
for the case where foreign VGs are going to be read.
This same rescan is now also performed when there is
an lvmetad token mismatch (from a changed global_filter).
The commands pvscan/vgscan/lvscan/vgimport are excluded
from this preemptive checking/rescanning for lvmetad
because they want to do rescanning themselves explicitly.
If rescanning devices fails, then lvmetad has not been
correctly repopulated and should not be used, so make
the command revert to not using lvmetad.
When not using lvmetad, this uses the system_id field in
the cached vginfo structs that are populated during a scan.
When using lvmetad, this requests the VG from lvmetad, and
checks the system_id field in the returned metadata.
This is the client side handling of the global_invalid state
added to lvmetad in commit c595b50cec8a6b95c6ac4988912d1412f3cc0237.
The function added here:
. checks if the global state in lvmetad is invalid
. if so, scans disks to update the state in lvmetad
. clears the global_invalid flag in lvmetad
. updates the local udev db to reflect any changes
Some of descritpions were misleading at least. Some were completely
off the reality.
lvmetad_init doesn't re-establish or initialise a connection
lvmetad_active and lvmetad_connect_or_warn can do so.
In process_each_{vg,lv,pv} when no vgname args are given,
the first step is to get a list of all vgid/vgname on the
system. This is exactly what lvmetad returns from a
vg_list request. The current code is doing a vg_lookup
on each VG after the vg_list and populating lvmcache with
the info for each VG. These preliminary vg_lookup's are
unnecessary, because they will be done again when the
processing functions call vg_read. This patch eliminates
the initial round of vg_lookup's, which can roughly cut in
half the number of lvmetad requests and save a lot of extra work.
When lvm1 PVs are visible, and lvmetad is used, and the foreign
option was included in the reporting command, the reporting
command would fail after the 'pvscan all devs' function saw
the lvm1 PVs. There is no reason the command should fail
because of the lvm1 PVs; they should just be ignored.
We need to use proper filter chain when we disable lvmetad use
explicitly in the code by calling lvmetad_set_active(0) while
overriding existing configuration. We need to reinitialize filters
in this case so proper filter chain is used. The same applies
for the other way round - when we enable lvmetad use explicitly in
the code (though this is not yet used).
This prevents numerous VG refreshes on each "pvscan --cache -aay" call
if the VG is found complete. We need to issue the refresh only if the PV:
- is new
- was gone before and now it reappears (device "unplug/plug back" scenario)
- the metadata has changed
If using lv/vgchange --sysinit -aay and lvmetad is enabled, we'd like to
avoid the direct activation and rely on autoactivation instead so
it fits system initialization scripts.
But if we're calling lv/vgchange --sysinit -aay too early when even
lvmetad service is not started yet, we just need to do the direct
activation instead without printing any error messages (while
trying to connect to lvmetad and not finding its socket).
This patch adds two helper functions - "lvmetad_socket_present" and
"lvmetad_used" which can be used to check for this condition properly
and avoid these lvmetad connections when the socket is not present
(and hence lvmetad is not yet running).
fmt1 doesn't have a separate commit function: updates take effect
immediately vg_write is called, so we must update lvmetad at this
point if we're going to go on and ask lvmetad for the VG metadata
again before calling the commit function (though that's probably an
unsupported and pointless thing to do anyway as the client must
already have that data and it cannot have changed because it's locked
and with devs suspended we shouldn't be communicating with lvmetad;
so when that's fixed properly, this fix here can be reverted).
This problem showed up as an internal error when lvremoving an LVM1
snapshot.
> Internal error: LV snap1 (00000000000000000000000000000001) missing from preload metadata
https://bugzilla.redhat.com/891855
Rename lvmetad_warning() to lvmetad_connect_or_warn().
Log all connection attempts on the client side, whether successful or not.
Reduce some nesting and remove a redundant assertion.
Calling pvscan --cache with -aay on a PV without an MDA would spuriously fail
with an internal error, because of an incorrect assumption that a parsed VG
structure was always available. This is not true and the autoactivation handler
needs to call vg_read to obtain metadata in cases where the PV had no MDAs to
parse. Therefore, we pass vgid into the handler instead of the (possibly NULL)
VG coming from the PV's MDA.
We were using daemon_send_simple until now, but it is no longer adequate, since
we need to manipulate requests in a generic way (adding a validity token to each
request), and the tree-based request interface is much more suitable for this.
Define an 'activation_handler' that gets called automatically on
PV appearance/disappearance while processing the lvmetad_pv_found
and lvmetad_pv_gone functions that are supposed to update the
lvmetad state based on PV availability state. For now, the actual
support is for PV appearance only, leaving room for PV disappearance
support as well (which is a more complex problem to solve as this
needs to count with possible device stack).
Add a new activation change mode - CHANGE_AAY exposed as
'--activate ay/-aay' argument ('activate automatically').
Factor out the vgchange activation functionality for use in other
tools (like pvscan...).
Add 3rd daemon return state "unknown" for lookups that are carried out
successfully but don't find the item requested.
Avoid issuing error messages when it's expected that a device that's
being looked up in lvmetad might not be there.
Hold global lock in pvscan --lvmetad. (This might need refinement.)
Add PV name to "PV gone" messages.
Adjust some log message severities. (More changes needed.)
