IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Since we check for present DM devices - cache result for
futher use of checking presence of such device.
lvm2 uses cache result for label scan, but also when
it tries to activate or deactivate LV - however only simple
target 'striped' is reasonably supported.
Use disable_dm_devs to be able to control when lv_info()
get cache or uncached results.
TODO: support more type, however this is getting very complicated.
Port another optimization from pvscan -aay to vgchange -aay:
"pvscan: only add device args to dev cache"
This optimization avoids doing a full dev_cache_scan, and
instead populates dev-cache with only the devices in the
VG being activated.
This involves shifting the use of pvs_online files from
the hints interface up to the higher level label_scan
interface. This specialized label_scan is structured
around creating a list of devices from the pvs_online
files. Previously, a list of all devices was created
first, and then reduced based on the pvs_online files.
The initial step of listing all devices was slow when
thousands of devices are present on the system.
This optimization extends the previous optimization that
used pvs_online files to limit the devices that were
actually scanned (i.e. reading to identify the device):
"vgchange -aay: optimize device scan using pvs_online files"
The information in /run/lvm/pvs_online/<pvid> files can
be used to build a list of devices for a given VG.
The pvscan -aay command has long used this information to
activate a VG while scanning only devices in that VG, which
is an important optimization for autoactivation.
This patch implements the same thing through the existing
device hints interface, so that the optimization can be
applied elsewhere. A future patch will take advantage of
this optimization in vgchange -aay, which is now used in
place of pvscan -aay for event activation.
When a device id is set for a device, using an idtype other
than devname, it means that sysfs has been used with the device
to match the device id. So, checking for a sysfs entry for the
device in filter-sysfs is redundant. For any other cases not
covered by this (e.g. devname ids), have filter-sysfs simply
stat /sys/dev/block/major:minor to test if the device exists
in sysfs.
The extensive processing done by filter-sysfs init is removed.
It was taking an immense amount of time with many devices, e.g.
. 1024 PVs in 520 VGs
. 520 concurrent vgchange -ay <vgname> commands
. vgchange scans only PVs in the named VG (based on pvs_online
files from a pending patch)
A large number of the vgchange commands were taking over 1 min,
and nearly half of that time was used by filter-sysfs init.
With this patch, the vgchange commands take about half the time.
Resolve event_activation configure option just once.
Do not print debug_devs about 'bad' filtering, when
actually filter already printed reason for skipping
Do not trace more then once about backup being disabled.
No debug when unlinked file does not exists in pvscan.
Just setting lvm.conf level=N should not send messages to
syslog (now the journal by default.)
Sending messages to syslog should require setting lvm.conf
log { syslog=1 level=N }.
Configure via lvm.conf log/journal or command line --journal.
Possible values:
"command" records command information.
"output" records default command output.
"debug" records full command debugging.
Multiple values can be set in lvm.conf as an array.
One value can be set in --journal which is added to
values set in lvm.conf
pvscan --cache <dev>
. read only dev
. create online file for dev
pvscan --listvg <dev>
. read only dev
. list VG using dev
pvscan --listlvs <dev>
. read only dev
. list VG using dev
. list LVs using dev
pvscan --cache --listvg [--checkcomplete] <dev>
. read only dev
. create online file for dev
. list VG using dev
. [check online files and report if VG is complete]
pvscan --cache --listlvs [--checkcomplete] <dev>
. read only dev
. create online file for dev
. list VG using dev
. list LVs using dev
. [check online files and report if VG is complete]
. [check online files and report if LVs are complete]
[--vgonline]
can be used with --checkcomplete, to enable use of a vg online
file. This results in only the first pvscan command to see
the complete VG to report 'VG complete', and others will report
'VG finished'. This allows the caller to easily run a single
activation of the VG.
[--udevoutput]
can be used with --cache --listvg --checkcomplete, to enable
an output mode that prints LVM_VG_NAME_COMPLETE='vgname' that
a udev rule can import, and prevents other output from the
command (other output causes udev to ignore the command.)
The list of complete LVs is meant to be passed to lvchange -aay,
or the complete VG used with vgchange -aay.
When --checkcomplete is used, lvm assumes that that the output
will be used to trigger event-based autoactivation, so the pvscan
does nothing if event_activation=0 and --checkcomplete is used.
Example of listlvs
------------------
$ lvs -a vg -olvname,devices
LV Devices
lv_a /dev/loop0(0)
lv_ab /dev/loop0(1),/dev/loop1(1)
lv_abc /dev/loop0(3),/dev/loop1(3),/dev/loop2(1)
lv_b /dev/loop1(0)
lv_c /dev/loop2(0)
$ pvscan --cache --listlvs --checkcomplete /dev/loop0
pvscan[35680] PV /dev/loop0 online, VG vg incomplete (need 2).
VG vg incomplete
LV vg/lv_a complete
LV vg/lv_ab incomplete
LV vg/lv_abc incomplete
$ pvscan --cache --listlvs --checkcomplete /dev/loop1
pvscan[35681] PV /dev/loop1 online, VG vg incomplete (need 1).
VG vg incomplete
LV vg/lv_b complete
LV vg/lv_ab complete
LV vg/lv_abc incomplete
$ pvscan --cache --listlvs --checkcomplete /dev/loop2
pvscan[35682] PV /dev/loop2 online, VG vg is complete.
VG vg complete
LV vg/lv_c complete
LV vg/lv_abc complete
Example of listvg
-----------------
$ pvscan --cache --listvg --checkcomplete /dev/loop0
pvscan[35684] PV /dev/loop0 online, VG vg incomplete (need 2).
VG vg incomplete
$ pvscan --cache --listvg --checkcomplete /dev/loop1
pvscan[35685] PV /dev/loop1 online, VG vg incomplete (need 1).
VG vg incomplete
$ pvscan --cache --listvg --checkcomplete /dev/loop2
pvscan[35686] PV /dev/loop2 online, VG vg is complete.
VG vg complete
The new system_id_source="appmachineid" will cause
lvm to use an lvm-specific derivation of the machine-id,
instead of the machine-id directly. This is now
recommended in place of using machineid.
related to config settings:
obtain_device_info_from_udev (controls if lvm gets
a list of devices from readdir /dev or from libudev)
external_device_info_source (controls if lvm asks
libudev for device information)
. Make the obtain_device_list_from_udev setting
affect only the choice of readdir /dev vs libudev.
The setting no longer controls if udev is used for
device type checks.
. Change obtain_device_list_from_udev default to 0.
This helps avoid boot timeouts due to slow libudev
queries, avoids reported failures from
udev_enumerate_scan_devices, and avoids delays from
"device not initialized in udev database" errors.
Even without errors, for a system booting with 1024 PVs,
lvm2-pvscan times improve from about 100 sec to 15 sec,
and the pvscan command from about 64 sec to about 4 sec.
. For external_device_info_source="none", remove all
libudev device info queries, and use only lvm
native device info.
. For external_device_info_source="udev", first check
lvm native device info, then check libudev info.
. Remove sleep/retry loop when attempting libudev
queries for device info. udev info will simply
be skipped if it's not immediately available.
. Only set up a libdev connection if it will be used by
obtain_device_list_from_udev/external_device_info_source.
. For native multipath component detection, use
/etc/multipath/wwids. If a device has a wwid
matching an entry in the wwids file, then it's
considered a multipath component. This is
necessary to natively detect multipath
components when the mpath device is not set up.
How to trigger:
```
~ # export LVM_SYSTEM_DIR=_
~ # pvscan
No matching physical volumes found
double free or corruption (!prev)
Aborted (core dumped)
```
when LVM_SYSTEM_DIR is empty, _load_config_file() won't be called.
when LVM_SYSTEM_DIR is not empty, cfl->cft links into cmd->config_files
by _load_config_file()@lib/commands/toolcontext.c
core dumped code: _destroy_config()@lib/commands/toolcontext.c
```
/* CONFIG_FILE/CONFIG_MERGED_FILES */
if ((cft = remove_config_tree_by_source(cmd, CONFIG_MERGED_FILES)))
config_destroy(cft);
else if ((cft = remove_config_tree_by_source(cmd, CONFIG_FILE)))
config_destroy(cft); <=== first free the cft
dm_list_iterate_items(cfl, &cmd->config_files)
config_destroy(cfl->cft); <=== double free the cft
```
Fixes: c43f2f8ae0
Signed-off-by: Heming Zhao <heming.zhao@suse.com>
dev_cache_index_devs() is taking a large amount of time
when there are many PVs. The index keeps track of
devices that are currently in use by active LVs. This
info is used to print warnings for users in some limited
cases.
The checks/warnings that are enabled by the index are not
needed by pvscan --cache, so disable it in this case.
This may be expanded to other cases in future commits.
dev_cache_index_devs should also be improved in another
commit to avoid the extreme delays with many devices.
The LVM devices file lists devices that lvm can use. The default
file is /etc/lvm/devices/system.devices, and the lvmdevices(8)
command is used to add or remove device entries. If the file
does not exist, or if lvm.conf includes use_devicesfile=0, then
lvm will not use a devices file. When the devices file is in use,
the regex filter is not used, and the filter settings in lvm.conf
or on the command line are ignored.
LVM records devices in the devices file using hardware-specific
IDs, such as the WWID, and attempts to use subsystem-specific
IDs for virtual device types. These device IDs are also written
in the VG metadata. When no hardware or virtual ID is available,
lvm falls back using the unstable device name as the device ID.
When devnames are used, lvm performs extra scanning to find
devices if their devname changes, e.g. after reboot.
When proper device IDs are used, an lvm command will not look
at devices outside the devices file, but when devnames are used
as a fallback, lvm will scan devices outside the devices file
to locate PVs on renamed devices. A config setting
search_for_devnames can be used to control the scanning for
renamed devname entries.
Related to the devices file, the new command option
--devices <devnames> allows a list of devices to be specified for
the command to use, overriding the devices file. The listed
devices act as a sort of devices file in terms of limiting which
devices lvm will see and use. Devices that are not listed will
appear to be missing to the lvm command.
Multiple devices files can be kept in /etc/lvm/devices, which
allows lvm to be used with different sets of devices, e.g.
system devices do not need to be exposed to a specific application,
and the application can use lvm on its own set of devices that are
not exposed to the system. The option --devicesfile <filename> is
used to select the devices file to use with the command. Without
the option set, the default system devices file is used.
Setting --devicesfile "" causes lvm to not use a devices file.
An existing, empty devices file means lvm will see no devices.
The new command vgimportdevices adds PVs from a VG to the devices
file and updates the VG metadata to include the device IDs.
vgimportdevices -a will import all VGs into the system devices file.
LVM commands run by dmeventd not use a devices file by default,
and will look at all devices on the system. A devices file can
be created for dmeventd (/etc/lvm/devices/dmeventd.devices) If
this file exists, lvm commands run by dmeventd will use it.
Internal implementaion:
- device_ids_read - read the devices file
. add struct dev_use (du) to cmd->use_devices for each devices file entry
- dev_cache_scan - get /dev entries
. add struct device (dev) to dev_cache for each device on the system
- device_ids_match - match devices file entries to /dev entries
. match each du on cmd->use_devices to a dev in dev_cache, using device ID
. on match, set du->dev, dev->id, dev->flags MATCHED_USE_ID
- label_scan - read lvm headers and metadata from devices
. filters are applied, those that do not need data from the device
. filter-deviceid skips devs without MATCHED_USE_ID, i.e.
skips /dev entries that are not listed in the devices file
. read lvm label from dev
. filters are applied, those that use data from the device
. read lvm metadata from dev
. add info/vginfo structs for PVs/VGs (info is "lvmcache")
- device_ids_find_renamed_devs - handle devices with unstable devname ID
where devname changed
. this step only needed when devs do not have proper device IDs,
and their dev names change, e.g. after reboot sdb becomes sdc.
. detect incorrect match because PVID in the devices file entry
does not match the PVID found when the device was read above
. undo incorrect match between du and dev above
. search system devices for new location of PVID
. update devices file with new devnames for PVIDs on renamed devices
. label_scan the renamed devs
- continue with command processing
dm-integrity stores checksums of the data written to an
LV, and returns an error if data read from the LV does
not match the previously saved checksum. When used on
raid images, dm-raid will correct the error by reading
the block from another image, and the device user sees
no error. The integrity metadata (checksums) are stored
on an internal LV allocated by lvm for each linear image.
The internal LV is allocated on the same PV as the image.
Create a raid LV with an integrity layer over each
raid image (for raid levels 1,4,5,6,10):
lvcreate --type raidN --raidintegrity y [options]
Add an integrity layer to images of an existing raid LV:
lvconvert --raidintegrity y LV
Remove the integrity layer from images of a raid LV:
lvconvert --raidintegrity n LV
Settings
Use --raidintegritymode journal|bitmap (journal is default)
to configure the method used by dm-integrity to ensure
crash consistency.
Initialization
When integrity is added to an LV, the kernel needs to
initialize the integrity metadata/checksums for all blocks
in the LV. The data corruption checking performed by
dm-integrity will only operate on areas of the LV that
are already initialized. The progress of integrity
initialization is reported by the "syncpercent" LV
reporting field (and under the Cpy%Sync lvs column.)
Example: create a raid1 LV with integrity:
$ lvcreate --type raid1 -m1 --raidintegrity y -n rr -L1G foo
Creating integrity metadata LV rr_rimage_0_imeta with size 12.00 MiB.
Logical volume "rr_rimage_0_imeta" created.
Creating integrity metadata LV rr_rimage_1_imeta with size 12.00 MiB.
Logical volume "rr_rimage_1_imeta" created.
Logical volume "rr" created.
$ lvs -a foo
LV VG Attr LSize Origin Cpy%Sync
rr foo rwi-a-r--- 1.00g 4.93
[rr_rimage_0] foo gwi-aor--- 1.00g [rr_rimage_0_iorig] 41.02
[rr_rimage_0_imeta] foo ewi-ao---- 12.00m
[rr_rimage_0_iorig] foo -wi-ao---- 1.00g
[rr_rimage_1] foo gwi-aor--- 1.00g [rr_rimage_1_iorig] 39.45
[rr_rimage_1_imeta] foo ewi-ao---- 12.00m
[rr_rimage_1_iorig] foo -wi-ao---- 1.00g
[rr_rmeta_0] foo ewi-aor--- 4.00m
[rr_rmeta_1] foo ewi-aor--- 4.00m
Since we need to preserve allocated strings across 2 separate
activation calls of '_tree_action()' we need to use other mem
pool them dm->mem - but since cmd->mem is released between
individual lvm2 locking calls, we rather introduce a new separate
mem pool just for pending deletes with easy to see life-span.
(not using 'libmem' as it would basicaly keep allocations over
the whole lifetime of clvmd)
This patch is fixing previous commmit where the memory was
improperly used after pool release.
With previous patch 30a98e4d67 we
started to put devices one pending_delete list instead
of directly scheduling their removal.
However we have operations like 'snapshot merge' where we are
resuming device tree in 2 subsequent activation calls - so
1st such call will still have suspened devices and no chance
to push 'remove' ioctl.
Since we curently cannot easily solve this by doing just single
activation call (which would be preferred solution) - we introduce
a preservation of pending_delete via command structure and
then restore it on next activation call.
This way we keep to remove devices later - although it might be
not the best moment - this may need futher tunning.
Also we don't keep the list of operation in 1 trasaction
(unless we do verify udev symlinks) - this could probably
also make it more correct in terms of which 'remove' can
be combined we already running 'resume'.
Avoid having PVs with different logical block sizes in the same VG.
This prevents LVs from having mixed block sizes, which can produce
file system errors.
The new config setting devices/allow_mixed_block_sizes (default 0)
can be changed to 1 to return to the unrestricted mode.
The exported VG checking/enforcement was scattered and
inconsistent. This centralizes it and makes it consistent,
following the existing approach for foreign and shared
VGs/PVs, which are very similar to exported VGs/PVs.
The access policy that now applies to foreign/shared/exported
VGs/PVs, is that if a foreign/shared/exported VG/PV is named
on the command line (i.e. explicitly requested by the user),
and the command is not permitted to operate on it because it
is foreign/shared/exported, then an access error is reported
and the command exits with an error. But, if the command is
processing all VGs/PVs, and happens to come across a
foreign/shared/exported VG/PV (that is not explicitly named on
the command line), then the command silently skips it and does
not produce an error.
A command using tags or --select handles inaccessible VGs/PVs
the same way as a command processing all VGs/PVs, and will
not report/return errors if these inaccessible VGs/PVs exist.
The new policy fixes the exit codes on a somewhat random set of
commands that previously exited with an error if they were
looking at all VGs/PVs and an exported VG existed on the system.
There should be no change to which commands are allowed/disallowed
on exported VGs/PVs.
Certain LV commands (lvs/lvdisplay/lvscan) would previously not
display LVs from an exported VG (for unknown reasons). This has
not changed. The lvm fullreport command would previously report
info about an exported VG but not about the LVs in it. This
has changed to include all info from the exported VG.
and implement it based on a device, not based
on a pv struct (which is not available when the
device is not a part of the vg.)
currently only the vgremove command wipes outdated
pvs until more advanced recovery is added in a
subsequent commit
If udev info is missing for a device, (which would indicate
if it's an MD component), then do an end-of-device read to
check if a PV is an MD component. (This is skipped when
using hints since we already know devs in hints are good.)
A new config setting md_component_checks can be used to
disable the additional end-of-device MD checks, or to
always enable end-of-device MD checks.
When both hints and udev info are disabled/unavailable,
the end of PVs will now be scanned by default. If md
devices with end-of-device superblocks are not being
used, the extra I/O overhead can be avoided by setting
md_component_checks="start".
Save the previous duplicate PVs in a global list instead
of a list on the cmd struct. dmeventd reuses the cmd struct
for multiple commands, and the list entries between commands
were being freed (apparently), causing a segfault in dmeventd
when it tried to use items in cmd->unused_duplicate_devs
that had been saved there by the previous command.
There have been two file locks used to protect lvm
"global state": "ORPHANS" and "GLOBAL".
Commands that used the ORPHAN flock in exclusive mode:
pvcreate, pvremove, vgcreate, vgextend, vgremove,
vgcfgrestore
Commands that used the ORPHAN flock in shared mode:
vgimportclone, pvs, pvscan, pvresize, pvmove,
pvdisplay, pvchange, fullreport
Commands that used the GLOBAL flock in exclusive mode:
pvchange, pvscan, vgimportclone, vgscan
Commands that used the GLOBAL flock in shared mode:
pvscan --cache, pvs
The ORPHAN lock covers the important cases of serializing
the use of orphan PVs. It also partially covers the
reporting of orphan PVs (although not correctly as
explained below.)
The GLOBAL lock doesn't seem to have a clear purpose
(it may have eroded over time.)
Neither lock correctly protects the VG namespace, or
orphan PV properties.
To simplify and correct these issues, the two separate
flocks are combined into the one GLOBAL flock, and this flock
is used from the locking sites that are in place for the
lvmlockd global lock.
The logic behind the lvmlockd (distributed) global lock is
that any command that changes "global state" needs to take
the global lock in ex mode. Global state in lvm is: the list
of VG names, the set of orphan PVs, and any properties of
orphan PVs. Reading this global state can use the global lock
in sh mode to ensure it doesn't change while being reported.
The locking of global state now looks like:
lockd_global()
previously named lockd_gl(), acquires the distributed
global lock through lvmlockd. This is unchanged.
It serializes distributed lvm commands that are changing
global state. This is a no-op when lvmlockd is not in use.
lockf_global()
acquires an flock on a local file. It serializes local lvm
commands that are changing global state.
lock_global()
first calls lockf_global() to acquire the local flock for
global state, and if this succeeds, it calls lockd_global()
to acquire the distributed lock for global state.
Replace instances of lockd_gl() with lock_global(), so that the
existing sites for lvmlockd global state locking are now also
used for local file locking of global state. Remove the previous
file locking calls lock_vol(GLOBAL) and lock_vol(ORPHAN).
The following commands which change global state are now
serialized with the exclusive global flock:
pvchange (of orphan), pvresize (of orphan), pvcreate, pvremove,
vgcreate, vgextend, vgremove, vgreduce, vgrename,
vgcfgrestore, vgimportclone, vgmerge, vgsplit
Commands that use a shared flock to read global state (and will
be serialized against the prior list) are those that use
process_each functions that are based on processing a list of
all VG names, or all PVs. The list of all VGs or all PVs is
global state and the shared lock prevents those lists from
changing while the command is processing them.
The ORPHAN lock previously attempted to produce an accurate
listing of orphan PVs, but it was only acquired at the end of
the command during the fake vg_read of the fake orphan vg.
This is not when orphan PVs were determined; they were
determined by elimination beforehand by processing all real
VGs, and subtracting the PVs in the real VGs from the list
of all PVs that had been identified during the initial scan.
This is fixed by holding the single global lock in shared mode
while processing all VGs to determine the list of orphan PVs.
This reverts 518a8e8cfb
"lvmlockd: activate mirror LVs in shared mode with cmirrord"
because while activating a mirror LV with cmirrord worked,
changes to the active cmirror did not work.
When lvextend extends an LV that is active with a shared
lock, use this as a signal that other hosts may also have
the LV active, with gfs2 mounted, and should have the LV
refreshed to reflect the new size. Use the libdlmcontrol
run api, which uses dlm_controld/corosync to run an
lvchange --refresh command on other cluster nodes.
which defines the amount of memory that lvm will allocate
for bcache. Increasing this setting is required if it is
smaller than a single copy of VG metadata.
For users who do not want all of the fields included
in debug lines, let them specify in lvm.conf which
fields to include. timestamp, command[pid], and
file:line fields can all be disabled.
Without this, the output from different commands in a single
log file could not be separated.
Change the default "indent" setting to 0 so that the default
debug output does not include variable spaces in the middle
of debug lines.
Save the list of PVs in /run/lvm/hints. These hints
are used to reduce scanning in a number of commands
to only the PVs on the system, or only the PVs in a
requested VG (rather than all devices on the system.)
