IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
When an LVM mirror is up-converted (an additional image added), it creates
a temporary mirror stack. The lower-level mirror in the stack that is
created was not being activated exclusively - violating the exclusive nature
of the original mirror. We now check for exclusive activation of a mirror
before converting it, and if found, we ensure that the temporary mirror
is also exclusively activated.
Mirrors used to be created by first creating a linear device and then adding
the other images plus the log. Now mirrors are created by creating all the
images in one go and then adding the log separately. The new way ran into
the condition that cluster mirrors cannot change the log type (in the case
of creation, from core -> disk) while the mirror is not active. (It isn't
active because it is in the process of being created.) The reason this
condition is in place is because a remote node may have the mirror active, and
we don't want to alter the log underneath it.
What we really needed was a way of checking if the mirror was active remotely
but not locally, and in that case do not allow a change of the log. I've added
this check, and cluster mirrors can now be created again.
We've used udev fallback code till now to check whether udev
created/removed the entries in /dev correctly and if not,
a repair was done (giving a warning messagea about that).
This patch adds a possibility to enable this additional check
and subsequent fallback only when required (debugging purposes
mostly) and trust udev completely.
So let's disable the fallback code by default and add a new
configuration option "activation/udev_fallback".
(The original code for creating the nodes will still be used
in case the device directory that is set in lvm.conf differs
from the one that udev uses and also when activation/udev_rules
is set to 0 - otherwise we would end up with no nodes/symlinks
at all)
It's useful to keep the partial flag cached - so just move the call
for vg_mark_partil_lvs() into import_vg_from_config_tree() so it gets
evaluated before it goes through the lvmcache.
This patch should not present any functional change.
Note: It is rather temporal solution - proper place is probably inside the
'read' call back - but needs some more discussion.
For now using this minor hack.
As the ACTIVATE_EXCL could be set only in clvmd code - there is no
use for this test in lv_add_mirrors() function only called from
tools context.
FIXME: Add cluster test case for this.
To avoid modification of 'read-only' volume group structure
add a new structure to pass local data around the code for LV
activation.
As origin_only is one such flag - replace this parameter with new
struct lv_activate_opts.
More parameters might eventually become part of lv_activate_opts.
This was missing in liblvm and it caused all udev-related operations to
not take effect when using liblvm, e.g. obtaining the list of devices from udev
db instead of scanning the whole /dev which also recreated the .cache as a side
effect. This was also the case with udisks-lvm-pv-export prober which is run
from within udev rules whenever the CHANGE event is fired.
and use this for the LVM critical section logic. Also report an error if
code tries to load a table while any device is known to be in the
suspended state.
(If the variety of problems these changes are showing up can't be fixed
before the next release, the error messages can be reduced to debug
level.)
are affected by the move. (Currently it's possible for I/O to become
trapped between suspended devices amongst other problems.
The current fix was selected so as to minimise the testing surface. I
hope eventually to replace it with a cleaner one that extends the
deptree code.
Some lvconvert scenarios still suffer from related problems.
Patch adds check for stripe not only in direct
LV segment but also in mirror image segment.
This prevents bugs like:
# lvcreate -i2 -l10 -n lv vg_test
# lvconvert -m1 -i1 vg_test/lv
# lvreduce -f -l1 vg_test/lv
WARNING: Reducing active logical volume to 4.00 MiB
THIS MAY DESTROY YOUR DATA (filesystem etc.)
Reducing logical volume lv to 4.00 MiB
Segment extent reduction 9 not divisible by #stripes 2
Logical volume lv successfully resized
# lvremove -f vg_test
Segment extent reduction 1 not divisible by #stripes 2
LV segment lv:0-4294967295 is incorrectly listed as being used by LV lv_mimage_0
Internal error: LV segments corrupted in lv_mimage_0.
Currently some operation with striped mirrors lead
to corrupted metadata, this patch just add detection of such
situation.
Example:
# lvcreate -i2 -l10 -n lvs vg_test
# lvconvert -m1 vg_test/lvs
# lvreduce -f -l1 vg_test/lvs
Reducing logical volume lvs to 4.00 MiB
Segment extent reduction 9not divisible by #stripes 2
Logical volume lvs successfully resized
# lvremove vg_test/lvs
Segment extent reduction 1not divisible by #stripes 2
LV segment lvs:0-4294967295 is incorrectly listed as being used by LV lvs_mimage_0
Internal error: LV segments corrupted in lvs_mimage_0.
We should never remove more extents than requested by user,
so round up to next stripe boundary during lvreduce.
Also this fixes round to zero sized LV bug:
# lvcreate -i2 -I 64k -l10 -n lvs vg_test
# lvreduce -f -l1 vg_test/lvs
Rounding size (1 extents) down to stripe boundary size for segment (0 extents)
WARNING: Reducing active logical volume to 0
THIS MAY DESTROY YOUR DATA (filesystem etc.)
Reducing logical volume lvs to 0
Failed to suspend lvs
There's a possibility someone will use the '/' in the hostname. Since we
generate a temporary file name (path) including the hostname, any '/' would
be ambiguous.
We can always set such hostname using 'sethostname' from unistd.h. But the
'hostname' command already includes the check and removes the '/' char.
However, some old versions still allow that.
See: https://bugzilla.redhat.com/show_bug.cgi?id=711445.
Since this is only a temporary name and the possibility of this error is
quite negligible, we don't need any complex escape sequence here, just a
simple char replace.
