IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
. When using default settings, this commit should change
nothing. The first PE continues to be placed at 1 MiB
resulting in a metadata area size of 1020 KiB (for
4K page sizes; slightly smaller for larger page sizes.)
. When default_data_alignment is disabled in lvm.conf,
align pe_start at 1 MiB, based on a default metadata area
size that adapts to the page size. Previously, disabling
this option would result in mda_size that was too small
for common use, and produced a 64 KiB aligned pe_start.
. Customized pe_start and mda_size values continue to be
set as before in lvm.conf and command line.
. Remove the configure option for setting default_data_alignment
at build time.
. Improve alignment related option descriptions.
. Add section about alignment to pvcreate man page.
Previously, DEFAULT_PVMETADATASIZE was 255 sectors.
However, the fact that the config setting named
"default_data_alignment" has a default value of 1 (MiB)
meant that DEFAULT_PVMETADATASIZE was having no effect.
The metadata area size is the space between the start of
the metadata area (page size offset from the start of the
device) and the first PE (1 MiB by default due to
default_data_alignment 1.) The result is a 1020 KiB metadata
area on machines with 4KiB page size (1024 KiB - 4 KiB),
and smaller on machines with larger page size.
If default_data_alignment was set to 0 (disabled), then
DEFAULT_PVMETADATASIZE 255 would take effect, and produce a
metadata area that was 188 KiB and pe_start of 192 KiB.
This was too small for common use.
This is fixed by making the default metadata area size a
computed value that matches the value produced by
default_data_alignment.
If a single, standard LV is specified as the cache, use
it directly instead of converting it into a cache-pool
object with two separate LVs (for data and metadata).
With a single LV as the cache, lvm will use blocks at the
beginning for metadata, and the rest for data. Separate
dm linear devices are set up to point at the metadata and
data areas of the LV. These dm devs are given to the
dm-cache target to use.
The single LV cache cannot be resized without recreating it.
If the --poolmetadata option is used to specify an LV for
metadata, then a cache pool will be created (with separate
LVs for data and metadata.)
Usage:
$ lvcreate -n main -L 128M vg /dev/loop0
$ lvcreate -n fast -L 64M vg /dev/loop1
$ lvs -a vg
LV VG Attr LSize Type Devices
main vg -wi-a----- 128.00m linear /dev/loop0(0)
fast vg -wi-a----- 64.00m linear /dev/loop1(0)
$ lvconvert --type cache --cachepool fast vg/main
$ lvs -a vg
LV VG Attr LSize Origin Pool Type Devices
[fast] vg Cwi---C--- 64.00m linear /dev/loop1(0)
main vg Cwi---C--- 128.00m [main_corig] [fast] cache main_corig(0)
[main_corig] vg owi---C--- 128.00m linear /dev/loop0(0)
$ lvchange -ay vg/main
$ dmsetup ls
vg-fast_cdata (253:4)
vg-fast_cmeta (253:5)
vg-main_corig (253:6)
vg-main (253:24)
vg-fast (253:3)
$ dmsetup table
vg-fast_cdata: 0 98304 linear 253:3 32768
vg-fast_cmeta: 0 32768 linear 253:3 0
vg-main_corig: 0 262144 linear 7:0 2048
vg-main: 0 262144 cache 253:5 253:4 253:6 128 2 metadata2 writethrough mq 0
vg-fast: 0 131072 linear 7:1 2048
$ lvchange -an vg/min
$ lvconvert --splitcache vg/main
$ lvs -a vg
LV VG Attr LSize Type Devices
fast vg -wi------- 64.00m linear /dev/loop1(0)
main vg -wi------- 128.00m linear /dev/loop0(0)
lvm uses a bcache block size of 128K. A bcache block
at the end of the metadata area will overlap the PEs
from which LVs are allocated. How much depends on
alignments. When lvm reads and writes one of these
bcache blocks to update VG metadata, it can also be
reading and writing PEs that belong to an LV.
If these overlapping PEs are being written to by the
LV user (e.g. filesystem) at the same time that lvm
is modifying VG metadata in the overlapping bcache
block, then the user's updates to the PEs can be lost.
This patch is a quick hack to prevent lvm from writing
past the end of the metadata area.
Previously the size was limited by checking if the
old and new copies of the metadata overlapped.
This generally limited the size to about half of
the total space, but it could be larger given the
size differences between old and new. Now add a
direct check to limit the size to half the space.
Remove another instance of an invalid check for metadata
overflow during read. The previous instance was removed
in commit 5fb15b193.
This was checking for metadata that that overflowed the
circular disk metadata buffer during read, but such metadata
cannot be written, so it shouldn't be possible to find see.
Also, the check was incorrect and could trigger when there
was no overflow.
The vg_write/vg_commit code was imprecise, uncommented, and
hard to understand. Rewrite it with clearer, cleaner code,
extensive comments, descriptions of how it works, and add
more info in debugging output.
The minor changes in behavior are to things that were
either incorrect or probably unintended:
- vg_write/vg_commit no longer check that the current vgname at
the start of the text metadata matches the vgname being written.
This has already been done at least twice by the time they are
called, and repeating it again against the same cached data has
no use.
- A fragment of old removed code had been left behind that checked
if the old unused alignment policy would wrap. It was still
being checked to decide if the metadata area was full, which
could possibly cause an incorrect full metadata failure.
- vg_remove now clears both the raw_locns in the mda_header that
point to committed metadata (raw_locn slot 0) and precommitted
metadata (raw_locn slot 1). Previously it fully cleared the
committed slot, and would only clear the offset field in the
precommitted slot if it saw a problem with the metadata in the
vg being removed.
- read_metadata_location_summary was wrongly comparing the number
of wrapped bytes with an offset to report an error about the
metadata being too large. This wrong check is removed, it
could have resulted in erroneous errors.
Native disk scanning is now both reduced and
async/parallel, which makes it comparable in
performance (and often faster) when compared
to lvm using lvmetad.
Autoactivation now uses local temp files to record
online PVs, and no longer requires lvmetad.
There should be no apparent command-level change
in behavior.
As we start refactoring the code to break dependencies (see doc/refactoring.txt),
I want us to use full paths in the includes (eg, #include "base/data-struct/list.h").
This makes it more obvious when we're breaking abstraction boundaries, eg, including a file in
metadata/ from base/
There are likely more bits of code that can be removed,
e.g. lvm1/pool-specific bits of code that were identified
using FMT flags.
The vgconvert command can likely be reduced further.
The lvm1-specific config settings should probably have
some other fields set for proper deprecation.
For reporting commands (pvs,vgs,lvs,pvdisplay,vgdisplay,lvdisplay)
we do not need to repeat the label scan of devices in vg_read if
they all had matching metadata in the initial label scan. The
data read by label scan can just be reused for the vg_read.
This cuts the amount of device i/o in half, from two reads of
each device to one. We have to be careful to avoid repairing
the VG if we've skipped rescanning. (The VG repair code is very
poor, and will be redone soon.)
Recent changes allow some major simplification of the way
lvmcache works and is used. lvmcache_label_scan is now
called in a controlled fashion at the start of commands,
and not via various unpredictable side effects. Remove
various calls to it from other places. lvmcache_label_scan
should not be called from anywhere during a command, because
it produces an incorrect representation of PVs with no MDAs,
and misclassifies them as orphans. This has been a long
standing problem. The invalid flag and rescanning based on
that is no longer used and removed. The 'force' variation is
no longer needed and removed.
The improved detection of bad metadata when scanning
(where errors were ignored before) means we now have to
override some errors when forcibly erasing damaged metadata.
This is a temporary hacky workaround to the problem of
reads going through bcache and writes not using bcache.
The write path wants to read parts of data that it is
incrementally writing to disk, but the reads (using
bcache) don't work because the writes are not in the
bcache. For now, add a dev to bcache before each attempt
to read it in case it's being used on the write path.
Create a new dev->bcache_fd that the scanning code owns
and is in charge of opening/closing. This prevents other
parts of lvm code (which do various open/close) from
interfering with the bcache fd. A number of dev_open
and dev_close are removed from the reading path since
the read path now uses the bcache.
With that in place, open(O_EXCL) for pvcreate/pvremove
can then be fixed. That wouldn't work previously because
of other open fds.
When process_each_pv() calls vg_read() on the orphan VG, the
internal implementation was doing an unnecessary
lvmcache_label_scan() and two unnecessary label_read() calls
on each orphan. Some of those unnecessary label scans/reads
would sometimes be skipped due to caching, but the code was
always doing at least one unnecessary read on each orphan.
The common format_text case was also unecessarily calling into
the format-specific pv_read() function which actually did nothing.
By analyzing each case in which vg_read() was being called on
the orphan VG, we can say that all of the label scans/reads
in vg_read_orphans are unnecessary:
1. reporting commands: the information saved in lvmcache by
the original label scan can be reported. There is no advantage
to repeating the label scan on the orphans a second time before
reporting it.
2. pvcreate/vgcreate/vgextend: these all share a common
implementation in pvcreate_each_device(). That function
already rescans labels after acquiring the orphan VG lock,
which ensures that the command is using valid lvmcache
information.
This fixes the use of lvmcache_label_rescan_vg() in the previous
commit for the special case of independent metadata areas.
label scan is about discovering VG name to device associations
using information from disks, but devices in VGs with
independent metadata areas have no information on disk, so
the label scan does nothing for these VGs/devices.
With independent metadata areas, only the VG metadata found
in files is used. This metadata is found and read in
vg_read in the processing phase.
lvmcache_label_rescan_vg() drops lvmcache info for the VG devices
before repeating the label scan on them. In the case of
independent metadata areas, there is no metadata on devices, so the
label scan of the devices will find nothing, so will not recreate
the necessary vginfo/info data in lvmcache for the VG. Fix this
by setting a flag in the lvmcache vginfo struct indicating that
the VG uses independent metadata areas, and label rescanning should
be skipped.
In the case of independent metadata areas, it is the metadata
processing in the vg_read phase that sets up the lvmcache
vginfo/info information, and label scan has no role.
Move the location of scans to make it clearer and avoid
unnecessary repeated scanning. There should be one scan
at the start of a command which is then used through the
rest of command processing.
Previously, the initial label scan was called as a side effect
from various utility functions. This would lead to it being called
unnecessarily. It is an expensive operation, and should only be
called when necessary. Also, this is a primary step in the
function of the command, and as such it should be called prominently
at the top level of command processing, not as a hidden side effect
of a utility function. lvm knows exactly where and when the
label scan needs to be done. Because of this, move the label scan
calls from the internal functions to the top level of processing.
Other specific instances of lvmcache_label_scan() are still called
unnecessarily or unclearly by specific commands that do not use
the common process_each functions. These will be improved in
future commits.
During the processing phase, rescanning labels for devices in a VG
needs to be done after the VG lock is acquired in case things have
changed since the initial label scan. This was being done by way
of rescanning devices that had the INVALID flag set in lvmcache.
This usually approximated the right set of devices, but it was not
exact, and obfuscated the real requirement. Correct this by using
a new function that rescans the devices in the VG:
lvmcache_label_rescan_vg().
Apart from being inexact, the rescanning was extremely well hidden.
_vg_read() would call ->create_instance(), _text_create_text_instance(),
_create_vg_text_instance() which would call lvmcache_label_scan()
which would call _scan_invalid() which repeats the label scan on
devices flagged INVALID. lvmcache_label_rescan_vg() is now called
prominently by _vg_read() directly.
To do label scanning, lvm code calls lvmcache_label_scan().
Change lvmcache_label_scan() to use the new label_scan()
based on bcache.
Also add lvmcache_label_rescan_vg() which calls the new
label_scan_devs() which does label scanning on only the
specified devices. This is for a subsequent commit and
is not yet used.
New label_scan function populates bcache for each device
on the system.
The two read paths are updated to get data from bcache.
The bcache is not yet used for writing. bcache blocks
for a device are invalidated when the device is written.
No longer use the external 'result' pointer internally to set up the
cached label. The callback _set_label_read_result() is now given the
internal label pointer directly
Callers that don't need the result are no longer required to pass a
label pointer into label_read().
Callers that read larger amounts of data now get a pointer to read-only
data directly without copying it through an intermediate buffer. This
data is owned by the device layer so the callers no longer free it.
If it obtains the data, it passes it into the supplied callback function
and returns 1. Otherwise the callback receives failed = 1.
Updated config_file_read_fd to use this and similarly return the data
via a callback fn of its own.
Dedicated functions are now used to process each piece of data obtained,
so the refactoring in this file gives us one for the vgsummary and one
for the metadata header. This new type of function takes two parameters
(for now), the obtained data plus a single struct (that must not
reference any data on the stack) that wraps up the entire context needed
to process it.
Rename dev_read() to dev_read_buf() - the function that reads data
into a supplied buffer.
Introduce a new dev_read() that allocates the buffer it returns and
switch the important users over to this. No caller may change the
returned data. (For now, callers are responsible for freeing it after
use, but later the device layer will take full ownership.)
dev_read_buf() should only be used for tiny buffers or unimportant code
(such as the old disk formats).
The creation of wrapped around metadata - where the start of metadata is
written up to the end of the buffer and the remainder follows back at
the start of the buffer - is now restricted to cases where writing the
metadata in one piece wouldn't fit. This shouldn't happen in 'normal'
usage so let's begin treating the code for this as a special case that
can be ignored when optimising 'normal' cases.
If there is sufficient space in the metadata area, align the next
metadata to a disk offset that is a multiple of 4096 bytes and
don't write it circularly. If it doesn't all fit at the end
of the metadata area, go back to the start and write it all there
contiguously.
If there is insufficient space to use the new stricter rules, revert to
the original behaviour, aligning on 512-byte boundaries wrapping around
the circular buffer as required.
Use new ALIGN_ABSOLUTE macro when calculating the start location
of new metadata and adjust the end of buffer detection so that
there is no longer an imposed gap between old and new metadata.
Currently both start and offset should always be divisible by alignment,
so this should have no effect, but a later patch will increase alignment
so these variables can no longer be optimised out.
Expand out the metadata wrapping calculations to prepare
to support a larger alignment.
The current alignment is 512 bytes so
(mdac_area_start + rlocn->offset) % alignment is zero.
Mark the first metadata area on each text format PV as MDA_PRIMARY.
Pass this information down to the device layer so that when
there are two metadata areas on a block device, we can easily
distinguish two independent streams of I/O.
Introduce enum dev_io_reason to categorise block device I/O
in debug messages so it's obvious what it is for.
DEV_IO_SIGNATURES /* Scanning device signatures */
DEV_IO_LABEL /* LVM PV disk label */
DEV_IO_MDA_HEADER /* Text format metadata area header */
DEV_IO_MDA_CONTENT /* Text format metadata area content */
DEV_IO_FMT1 /* Original LVM1 metadata format */
DEV_IO_POOL /* Pool metadata format */
DEV_IO_LV /* Content written to an LV */
DEV_IO_LOG /* Logging messages */
When an ignored metadata area gets flagged for use again, make sure the
code doesn't try to parse its old metadata. Firstly by trying to detect
this situation and skipping the read (while still remembering the
position reached in the circular buffer), and secondly by clearing the
invalid live metadata location on disk as a precaution when subsequently
writing out the precommitted metadata.
Problems showed up when a metadata area in one VG got moved to
another VG in ignored state (still holding metadata for the original
VG) and then later got brought into use in the new VG - only the header
should be read in this case, not any of the metadata content.
vgmerge suffers from a similar problem to the one fixed in commit
8146548d25 ("vgsplit: Fix intermediate
metadata corruption.")
When merging, splitting or renaming VGs, use a new PV status flag
PV_MOVED_VG to mark the PVs that hold metadata with the old VG name and
use this to provide PV-level granularity instead of incorrectly assuming
all PVs in the VG are the same.
Changing the VG of a PV uses the same on-disk mechanism as vgrename.
This relies on recognising both the old and new VG names. Prior to this
patch the vgsplit code incorrectly provided the new VG name twice
instead of the old and new ones. This lead the low-level mechanism not
to recognise the device as already belonging to a VG and so paying no
attention to the location of its existing metadata, sometimes partly
overwriting it and then later trying to read the corrupt metadata and
issuing a checksum error.
lvmcache_foreach_mda() can fail for numerous reasons
and failing error code cannot be ignored (out-of-memory...)
TODO: might need more error handling tunning.
Fix code checking that the 2nd mda which is at the end of disk really
fits the available free space and avoid any DA and MDA interleaving when
we already have DA preallocated. This mainly applies when we're restoring
a PV from VG backup using pvcreate --restorefile where we may already have
some DA preallocated - this means the PV was in a VG before with already
allocated space from it (the LVs were created). Hence we need to avoid
stepping into DA - the MDA can never ever be inside in such case!
The code responsible for this calculation was already in
_text_pv_add_metadata_area fn, but it had a bug in the calculation where
we subtracted one more sector by mistake and then the code could still
incorrectly allocate the MDA inside existing DA. The patch also renames
the variable in the code so it doesn't confuse us in future.
Also, if the 2nd mda doesn't fit, don't silently continue with just 1
MDA (at the start of the disk). If 2nd mda was requested and we can't
create that due to unavailable space, error out correctly (the patch
also adds a test to shell/pvcreate-operation.sh for this case).
In order to reject out of place reshaping with segment data_offset
field on old runtime, add a respective segment type incompatibility
flag causing "+RESHAPE_DATA_OFFSET" to be suffixed to the segment
type name.
Prohibit activation of reshaping RaidLVs on incompatible
lvm2 runtime by storing e.g. 'raid5+RESHAPE' segment type
strings in the lvm2 metadata. Incompatible runtime not
supporting reshaping won't be able to activate those thus
avoiding potential data corruption.
Any new non-reshaping lvconvert command will reset the
segment type string from 'raid5+RESHAPE' to 'raid5'.
See commits
0299a7af1e and
4141409eb0
for segtype flag support.
Since lvmetad is using 'MISSING' in status for 'another' purpose,
we need to support ATM also flag get from this place.
Until fixed better - we accept both flags - alhough lvm2 will
only print in flags.
Switch METADATA_FORMAT flag usage to be stored via segtype
instead of 'status' flag which appeared to cause major
incompatibility troubles.
For backward compatiblity segtype flags are still accepted also
via 'status' bits which were used from version 2.02.169 so metadata
saved by this newer lvm2 version should still work nicely, although
new save version will no longer work on this older lvm2 version.
Allow storing LV status bits with segment type name field.
Switching to this since this field has better support for compatibility
with older version of lvm2 - since such unknown segtype will not cause
complete invisiblity of metadata from older lvm2 code - just the
particular LV will become unusable with unknown type of segment.
This patch fixed lvm2 compilation running on x32 arch.
(Using 64bit x86 cpu features but running on 32b address space,
so consuming less mem in VM).
On x32 arch 'time_t' is 64bit while 'long' is 32bit.
Cache pool read/writes metadata_format within its segment type..
For CachePoolLV unselected metadata format is NOT stored in metadata.
For CacheLV when metadata format is not present/selected in lvm2 metadata,
it's automatically assumed to be the version 1 (backward compatible).
To ensure older lvm2 will not 'miss-read' metadata with new version 2,
such LV is marked with METADATA_FORMAT status flag (segment is
specifying metadata format). So when cache uses metadata format 2,
it will become inaccesible on older system without such support.
(kernel dm cache < 1.10, lvm2 < 2.02.169).
In order to support striped raid5/6/10 LV reshaping (change
of LV type, stripesize or number of legs), this patch
introduces infrastructure prerequisites to be used
by raid_manip.c extensions in followup patches.
This base is needed for allocation of out-of-place
reshape space required by the MD raid personalities to
avoid writing over data in-place when reading off the
current RAID layout or number of legs and writing out
the new layout or to a different number of legs
(i.e. restripe)
Changes:
- add members reshape_len to 'struct lv_segment' to store
out-of-place reshape length per component rimage
- add member data_copies to struct lv_segment
to support more than 2 raid10 data copies
- make alloc_lv_segment() aware of both reshape_len and data_copies
- adjust all alloc_lv_segment() callers to the new API
- add functions to retrieve the current data offset (needed for
out-of-place reshaping space allocation) and the devices count
from the kernel
- make libdm deptree code aware of reshape_len
- add LV flags for disk add/remove reshaping
- support import/export of the new 'struct lv_segment' members
- enhance lv_extend/_lv_reduce to cope with reshape_len
- add seg_is_*/segtype_is_* macros related to reshaping
- add target version check for reshaping
- grow rebuilds/writemostly bitmaps to 246 bit to support kernel maximal
- enhance libdm deptree code to support data_offset (out-of-place reshaping)
and delta_disk (legs add/remove reshaping) target arguments
Related: rhbz834579
Related: rhbz1191935
Related: rhbz1191978
When command calls backup() more then once (which is actually not
wanted) this warning message is shown repeatedly:
"WARNING: This metadata update is NOT backed up."
Instead now print message just once and less confuse user.
Previously, a command sent lvmetad new VG metadata in vg_commit().
In vg_commit(), devices are suspended, so any memory allocation
done by the command while sending to lvmetad, or by lvmetad while
updating its cache could deadlock if memory reclaim was triggered.
Now lvmetad is updated in unlock_vg(), after devices are resumed.
The new method for updating VG metadata in lvmetad is in two phases:
1. In vg_write(), before devices are suspended, the command sends
lvmetad a short message ("set_vg_info") telling it what the new
VG seqno will be. lvmetad sees that the seqno is newer than
the seqno of its cached VG, so it sets the INVALID flag for the
cached VG. If sending the message to lvmetad fails, the command
fails before the metadata is committed and the change is not made.
If sending the message succeeds, vg_commit() is called.
2. In unlock_vg(), after devices are resumed, the command sends
lvmetad the standard vg_update message with the new metadata.
lvmetad sees that the seqno in the new metadata matches the
seqno it saved from set_vg_info, and knows it has the latest
copy, so it clears the INVALID flag for the cached VG.
If a command fails between 1 and 2 (after committing the VG on disk,
but before sending lvmetad the new metadata), the cached VG retains
the INVALID flag in lvmetad. A subsequent command will read the
cached VG from lvmetad, see the INVALID flag, ignore the cached
copy, read the VG from disk instead, update the lvmetad copy
with the latest copy from disk, (this clears the INVALID flag
in lvmetad), and use the correct VG metadata for the command.
(This INVALID mechanism already existed for use by lvmlockd.)
Previously, vgcfgrestore would attempt to vg_remove the
existing VG from lvmetad and then vg_update to add the
restored VG. But, if there was a failure in the command
or with vg_update, the lvmetad cache would be left incorrect.
Now, disable lvmetad before the restore begins, and then
rescan to populate lvmetad from disk after restore has
written the new VG to disk.
A number of places are working on a specific dev when they
call lvmcache_info_from_pvid() to look up an info struct
based on a pvid. In those cases, pass the dev being used
to lvmcache_info_from_pvid(). When a dev is specified,
lvmcache_info_from_pvid() will verify that the cached
info it's using matches the dev being processed before
returning the info. Calling code will not mistakenly
get info for the wrong dev when duplicate devs exist.
This confusion was happening when scanning labels when
duplicate devs existed. label_read for the first dev
would add an info struct to lvmcache for that dev/pvid.
label_read for the second dev would see the pvid in
lvmcache from first dev, and mistakenly conclude that
the label_read from the second dev can be skipped
because it's already been done. By verifying that the
dev for the cached pvid matches the dev being read,
this mismatch is avoided and the label is actually read
from the second duplicate.
The lvmetad connection is created within the
init_connections() path during command startup,
rather than via the old lvmetad_active() check.
The old lvmetad_active() checks are replaced
with lvmetad_used() which is a simple check that
tests if the command is using/connected to lvmetad.
The old lvmetad_set_active(cmd, 0) calls, which
stopped the command from using lvmetad (to revert to
disk scanning), are replaced with lvmetad_make_unused(cmd).
The code in _print_historical_lv function works with temporary
"descendants_buffer" that is allocated and freed within this
function.
When printing text out, we used "outf" macro which called
"out_text" fn and it checked return value and if failed,
the macro called "return_0" automatically. But since we
use the temporary buffer, if any of the out_text calls
fails, we need to deallocate this buffer properly - that's
the "goto_out", otherwise we'll be leaking memory.
So add new "outfgo" helper macro which does the same as "outf",
but it calls "goto_out" instead of "return_0" so we can jump
to a cleanup hook at the end.
Also export historical LVs when exporting LVM2 metadata.
This is list of all historical LVs listed in
"historical_logical_volumes" metadata section with all
the properties exported for each historical LV.
For example, we have this thin snapshot sequence:
lvol1 --> lvol2 --> lvol3
\
--> lvol4
We end up with these metadata:
logical_volume {
...
(lvol1, lvol3 and lvol4 listed here as usual - no change here)
...
}
historical_logical_volumes {
lvol2 {
id = "S0Dw1U-v5sF-LwAb-W9SI-pNOF-Madd-5dxSv5"
creation_time = 1456919613 # 2016-03-02 12:53:33 +0100
removal_time = 1456919620 # 2016-03-02 12:53:40 +0100
origin = "lvol1"
descendants = ["lvol3", "lvol4"]
}
}
By removing lvol1 further, we end up with:
historical_logical_volumes {
lvol2 {
id = "S0Dw1U-v5sF-LwAb-W9SI-pNOF-Madd-5dxSv5"
creation_time = 1456919613 # 2016-03-02 12:53:33 +0100
removal_time = 1456919620 # 2016-03-02 12:53:40 +0100
origin = "-lvol1"
descendants = ["lvol3", "lvol4"]
}
lvol1 {
id = "me0mes-aYnK-nRfT-vNlV-UiR1-GP7r-ojbROr"
creation_time = 1456919608 # 2016-03-02 12:53:28 +0100
removal_time = 1456919767 # 2016-03-02 12:56:07 +0100
}
}
This uses the vg->pv_write_list in place of the
vg->pvs_to_write list, and eliminates the use of
pvcreate_params. The label remove and zeroing
steps are shifted out of vg_write() to the higher
level like pvcreate will do.
The backup_restore_vg is used directly for restoring the VG from backup.
It's also used to do the VG conversions from one metadata format to
another which means vgconvert calls backup_restore_vg too.
When restoring VG from backup, we need to rewrite/write PV headers as
PVs may have been orphans before and now they're becoming part of some
VG - we need to write the PV_EXT_USED flag at least.
When using the backup_restore_vg for vgconvert, we need to write
completely new PV header in different format.
Avoid the special "pv_write" call and handling that was used before
this patch in vgconvert (vgconvert_single function to be more precise)
and reuse existing internal interface to register PV header for writing
(or rewriting) via vg->pvs_to_write list instead like we do it elsewhere
in the code.
This patch also resolves a problem in which PV headers with target
format were written in the vgconvert_single fn as orphans and VG
metadata were added later on - this was a tiny hack actually.
We can't do this now - we need to write the PV as belonging
to a VG because otherwise the PV_EXT_USED flag won't be written
properly (if the PV header is written as orphan, the PV_EXT_USED
is set to 0, of course, even though metadata are attached later).
So this patch removes this tiny inconsistency which was passing
just fine before because we didn't have any relation to the VG
in PV header before. Now we have the PV_EXT_USED flag which says
the "PV is used in some VG".
Use process_each_vg() to lock and read the old VG,
and then call the main vgrename code.
When real VG names are used (not a UUID in place of the
old name), the command still pre-locks the new name
(when strcmp wants it locked first), before calling
process_each_vg on the old name.
In the case where the old name is replaced with a UUID,
process_each_vg now translates that UUID into the real
VG name, which it locks and reads. In this case, we
cannot do pre-locking to maintain lock ordering because
the old name is unknown. So, in this case the strcmp
based lock ordering is suppressed and the old name is
always locked first. This opens a remote chance for
lock ordering conflict between racing vgrenames between
two names where one or both commands use the UUID.
It's getting a bit more complex here.
Basic idea behind is - check_current_backup() should not
log error when a user is using a read-only filesystem,
so e.g. vgscan will not report any error when it tries
to take missing backup.
We still have cases when error could be reported though,
e.g. the backup this would be a symbolic link, but these
are rather misconfiguration and unexpected case.
