IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Move common code for changing activation state from
vgchange and lvchange to one function.
Fix the order of checks - so we always implicitelly
activate snapshots and thin volumes in exclusive mode,
and we do not allow local deactivation for them.
Use log_warn to print non-fatal warning messages.
Use of log_error would confuse checker for testing
whether proper error has been reported for some real error.
A while back, the behavior of LVM changed from allowing metadata changes
when PVs were missing to not allowing changes. Until recently, this
change was tolerated by HA-LVM by forcing a 'vgreduce --removemissing'
before trying (again) to add tags to an LV and then activate it. LVM
mirroring requires that failed devices are removed anyway, so this was
largely harmless. However, RAID LVs do not require devices to be removed
from the array in order to be activated. In fact, in an HA-LVM
environment this would be very undesirable. Device failures in such an
environment can often be transient and it would be much better to restore
the device to the array than synchronize an entirely new device.
There are two methods that can be used to setup an HA-LVM environment:
"clvm" or "tagging". For RAID LVs, "clvm" is out of the question because
RAID LVs are not supported in clustered VGs - not even in an exclusively
activated manner. That leaves "tagging". HA-LVM uses tagging - coupled
with 'volume_list' - to ensure that only one machine can have an LV active
at a time. If updates are not allowed when a PV is missing, it is
impossible to add or remove tags to allow for activation. This removes
one of the most basic functionalities of HA-LVM - site redundancy. If
mirroring or RAID is used to replicate the storage in two data centers
and one of them goes down, a server and a storage device are lost. When
the service fails-over to the alternate site, the VG will be "partial".
Unable to add a tag to the VG/LV, the RAID device will be unable to
activate.
The solution is to allow vgchange and lvchange to alter the LVM metadata
for a limited set of options - --[add|del]tag included. The set of
allowable options are ones that do not cause changes to the DM kernel
target (like --resync would) or could alter the structure of the LV
(like allocation or conversion).
Using 'activation/auto_activation_volume_list = [ "vg/lvol1" ]'.
Before this patch:
3 logical volume(s) in volume group "vg" now active
LV VG Attr LSize Pool Origin Data% Move Log Copy% Convert
lvol0 vg -wi----- 4.00m
lvol1 vg -wi-a--- 4.00m
lvol2 vg -wi-a--- 4.00m
lvol3 vg -wi-a--- 4.00m
(vg/lvol1 activated as it passes the list and all subsequent volumes too - wrong!)
With this patch:
1 logical volume(s) in volume group "vg" now active
LV VG Attr LSize Pool Origin Data% Move Log Copy% Convert
lvol0 vg -wi----- 4.00m
lvol1 vg -wi-a--- 4.00m
lvol2 vg -wi----- 4.00m
lvol3 vg -wi----- 4.00m
(only vg/lvol1 activated as it passes the list and no other - correct!)
Accept -q as the short form of --quiet.
Suppress non-essential standard output if -q is given twice.
Treat log/silent in lvm.conf as equivalent to -qq.
Review all log_print messages and change some to
log_print_unless_silent.
When silent, the following commands still produce output:
dumpconfig, lvdisplay, lvmdiskscan, lvs, pvck, pvdisplay,
pvs, version, vgcfgrestore -l, vgdisplay, vgs.
[Needs checking.]
Non-essential messages are shifted from log level 4 to log level 5
for syslog and lvm2_log_fn purposes.
When --sysinit -a ay is used with vg/lvchange and lvmetad is up and running,
we should skip manual activation as that would be a useless step - all volumes
are autoactivated once all the PVs for a VG are present.
If lvmetad is not active at the time of the vgchange --sysinit -a ay
call, the activation proceeds in standard 'manual' way.
This way, we can still have vg/lvchange --sysinit -a ay called
unconditionally in system initialization scripts no matter if lvmetad
is used or not.
Normally, the 'vgchange -ay' activates all volume groups (that pass
the activation/volume_list filter if set).
This call can appear in two scenarios:
- system boot (so activation within a script in general)
- manual call on command line (so activaton on user's direct request)
For the former one, we would like to select which VGs should be actually
activated. One can define the list of VGs directly to do that. But that
would require the same list to be provided in all the scripts.
The 'vgchange -aay' will check for the activation/auto_activation_volume_list
in adition and it will activate only those VGs/LVs that pass this
filter (assuming all to be activated if the list is not defined - the
same logic we already have for activation/volume_list).
Init/boot scripts should use this form of activation primarily
(which, anyway, becomes only a fallback now with autoactivation done
on PV appearance in tandem with lvmetad in place).
Define an 'activation_handler' that gets called automatically on
PV appearance/disappearance while processing the lvmetad_pv_found
and lvmetad_pv_gone functions that are supposed to update the
lvmetad state based on PV availability state. For now, the actual
support is for PV appearance only, leaving room for PV disappearance
support as well (which is a more complex problem to solve as this
needs to count with possible device stack).
Add a new activation change mode - CHANGE_AAY exposed as
'--activate ay/-aay' argument ('activate automatically').
Factor out the vgchange activation functionality for use in other
tools (like pvscan...).
We're refererring to 'activation' all over the code and we're talking
about 'LVs being activated' all the time so let's use 'activation/activate'
everywhere for clarity and consistency (still providing the old
'available' keyword as a synonym for backward compatibility with
existing environments).
Code adds better support for monitoring of thin pool devices.
update_pool_lv uses DMEVENTD_MONITOR_IGNORE to not manipulate with monitoring.
vgchange & lvchange are checking real thin pool device for existance
as we are using _tpool real device and visible LV pool device might not
be even active (_tpool is activated implicitely for any thin volume).
monitor_dev_for_events is another _lv_postorder like code it might be worth
to think about reusing it here - for now update the code to properly
monitory thin volume deps.
For unmonitoring add extra code to check the usage of thin pool - in case it's in use
unmonitoring of thin volume is skipped.
Read lvm.conf setting for monitoring for each command. So we should not
activate monitoring if the default compilation is set to monitor during
lvconvert commnads.
Patch also removes check for clustered VG and allows to disable monitoring
for clustered VG with the assumption, the problem with monitoring and dmeventd
flag passing for INGNORE is already fixed.
All thins are created with the next activation and VG is updated
without messages. Only some basic commands works.
(i.e. lvcreate -an -V10 -T mvg/pool)
There can be some combination to confuse this system.
This functionality for snapshots is going to be interesting.
To ensure we properly handle LV cluster locking - explicitely do
not allow to change the availability of the thin pool that is in use
for some thin LV.
As soon as the thin volume is created the only way to activate pool
is via implicit dependency.
Ignore thinpool open count for lv/vgchange operations.
are affected by the move. (Currently it's possible for I/O to become
trapped between suspended devices amongst other problems.
The current fix was selected so as to minimise the testing surface. I
hope eventually to replace it with a cleaner one that extends the
deptree code.
Some lvconvert scenarios still suffer from related problems.
activated.
In order to achieve this, we need to be able to query whether
the origin is active exclusively (a condition of being able to
add an exclusive snapshot).
Once we are able to query the exclusive activation of an LV, we
can safely create/activate the snapshot.
A change to 'hold_lock' was also made so that a request to aquire
a WRITE lock did not replace an EX lock, which is already a form
of write lock.
Simultaneous -a and --refresh is not valid.
poll+monitor are valid together with or without -ay* (but not with -an*)
No longer print polling results summary if no LVs in the VG were polled.
Update logic in vgchange to handle --vgmetadatacopies, allow
--metadatacopies as a synonym to --vgmetadatacopies,
and add these parameters to args.h and commands.h
Forbit both --vgmetadatacopies and --metadatacopies as only
one allowed.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Activate only the first replicator-dev LV, that activates all other
related LVs from Replicator. In case of error during this activation,
it will not retry again for other heads (less confusing error log).
A shortcut for --ignorelockingfailure, --ignoremonitoring, --poll n options
and LVM_SUPPRESS_LOCKING_FAILURE_MESSAGES environment variable used all at
once in initialisation scripts (e.g. rc.sysinit or initrd).
clvmd does not propagate DMEVENTD_MONITOR_IGNORE.
Update get_activation_monitoring_mode() to check if the VG that the
LV is being activated in is clustered. If so, skip it.
Any get_activation_monitoring_mode() error will cause the associated LV
(or VG) to be skipped during activation. Both vgchange_single() and
lvchange_single(), which call get_activation_monitoring_mode(), are
called by their respective process_each_..() method.
. Add "monitoring" option to "activation" section of lvm.conf
. Have clvmd consult the lvm.conf "activation/monitoring" too.
. Introduce toollib.c:get_activation_monitoring_mode().
. Error out when both --monitor and --ignoremonitoring are provided.
. Add --monitor and --ignoremonitoring support to lvcreate. Update
lvcreate man page accordingly.
. Clarify that '--monitor' controls the start and stop of monitoring in
the {vg,lv}change man pages.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Pull out common code to be called from tools as well as lvm2app.
Leave archive() at tool level so we can use from vgcreate
as well as vgchange. Should be no functional change.
- add stack macro in vgchange
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Eliminate 'merging_snapshot' from 'struct logical_volume' and just use
'snapshot' for origin lv's reference to the merging snapshot; also set
MERGING in the origin lv's status.
the background polldaemon is allowed to start. It can be used
standalone or in conjunction with --refresh or --available y.
Control over when the background polldaemon starts will be particularly
important for snapshot-merge of a root filesystem.
Dracut will be updated to activate all LVs with: --poll n
The lvm2-monitor initscript will start polling with: --poll y
NOTE: Because we currently have no way of knowing if a background
polldaemon is active for a given LV the following limitations exist and
have been deemed acceptable:
1) it is not possible to stop an active polldaemon; so the lvm2-monitor
initscript doesn't stop running polldaemon(s)
2) redundant polldaemon instances will be started for all specified LVs
if vgchange or lvchange are repeatedly used with '--poll y'
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
