IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
If using persistent filter and we're refreshing filters (just like we
do for pvcreate now after commit 54685c20fc),
we can't rely on getting the primary device of the partition from the cache
as such device could be already filtered by persistent filter and we get
a device cache lookup failure for such device.
For example:
$ lvm dumpconfig --type diff
devices {
obtain_device_list_from_udev=0
}
$lsblk /dev/sda
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
sda 8:0 0 128M 0 disk
`-sda1 8:1 0 127M 0 part
$cat /etc/lvm/cache/.cache | grep sda
"/dev/sda1",
$pvcreate /dev/sda1
dev_is_mpath: failed to get device for 8:1
Physical volume "/dev/sda1" successfully created
The problematic part of the code called dev_cache_get_by_devt
to get the device for the device number supplied. Then the code
used dev_name(dev) to get the name which is then used in check
whether there's any mpath on top of this dev...
This patch uses sysfs to get the base name for the partition
instead, hence avoiding the device cache which is a correct
approach here.
This is a regression caused by commit 3bd9048854.
The error message added with that commit "mpath major %d is not dm major %d" is
superfluous.
When scanning for mpath components, we're looking for a parent device.
But this parent device is not necessarily an mpath device (so the dm device)
if it exists - it can be any other device layered on top (e.g. an MD RAID device).
Split out the partitioned device filter that needs to open the device
and move the multipath filter in front of it.
When a device is multipathed, sending I/O to the underlying paths may
cause problems, the most obvious being I/O errors visible to lvm if a
path is down.
Revert the incorrect <backtrace> messages added when a device doesn't
pass a filter.
Log each filter initialisation to show sequence.
Avoid duplicate 'Using $device' debug messages.
We use mpath filtering (enabled by devices/multipath_component_detection=1
lvm.conf setting) to avoid a situation in which we could end up with
duplicate PVs found. We need to filter out the mpath components and
use only the top-level multipath mapping instead for PV scans.
However, if the there are partitions on multipath components, we need
to filter out these partitions. This patch fixes it so those
partitions found on multipath components are filtered as well.
For example, let's consider following configuration:
The sda and sdb are mpath components, sda1 and sdb1 the partitions
on these components, mpath-test the mpath mapping and mpath-test1
the partition mapping - created automatically by kpartx right
after mpath-test creation. The PV resides on top.
(LVM PV)
|
mpath-test1
|
mpath-test
|
sda1 ---------- sdb1
\ | |/
sda sdb
E.g. for sda1 and sdb1, the code will detect this and it skips
the partition that belongs to the multipath component:
<snippet from the log>
#filters/filter-mpath.c:156 /dev/sda1: Device is a partition, using primary device /dev/sda for mpath component detection
130 #ioctl/libdm-iface.c:1724 dm status (253:2) OF[16384](*1)
131 #filters/filter-mpath.c:196 /dev/sda1: Skipping mpath component device
</snippet from the log>
Othewise, we'd see the same PV label on sda1/sdb1 and mpath-test1
at the same time ending up with "Duplicate PV found...".
Changes:
- move device type registration out of "type filter" (filter.c)
to a separate and new dev-type.[ch] for common use throughout the code
- the structure for keeping the major numbers detected for available
device types and available partitioning available is stored in
"dev_types" structure now
- move common partitioning detection code to dev-type.[ch] as well
together with other device-related functions bound to dev_types
(see dev-type.h for the interface)
The dev-type interface contains all common functions used to detect
subsystems/device types, signature/superblock recognition code,
type-specific device properties and other common device properties
(bound to dev_types), including partitioning support.
- add dev_types instance to cmd context as cmd->dev_types for common use
- use cmd->dev_types throughout as a central point for providing
information about device types
