IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
and use this for the LVM critical section logic. Also report an error if
code tries to load a table while any device is known to be in the
suspended state.
(If the variety of problems these changes are showing up can't be fixed
before the next release, the error messages can be reduced to debug
level.)
With the ability to stack many operations in one udev transaction -
in same cases we are adding and removing same device at the same time
(i.e. deactivate followed by activate).
This leads to a problem of checking stacked operations:
i.e. remove /dev/node1 followed by create /dev/node1
If the node creation is handled with udev - there is a problem as
stacked operation gives warning about existing node1 and will try to
remove it - while next operation needs to recreate it.
Current code removes all previous stacked operation if the fs op is
FS_DEL - patch adds similar behavior for FS_ADD - it will try to
remove any 'delete' operation if udev is in use.
For FS_RENAME operation it seems to be more complex. But as we
are always stacking FS_READ_AHEAD after FS_ADD operation -
should be safe to remove all previous operation on the node
when udev is running.
Code does same checking for stacking libdm and liblvm operations.
As a very simple optimization counters were added for each stacked ops
type to avoid unneeded list scans if some operation does not exists in
the list.
Enable skipping of fs_unlock() (udev sync) if only DEL operations are staked.
as we do not use lv_info for already deleted nodes.
Detect existence of new SELinux selabel interface during configure.
Use new dm_prepare_selinux_context instead of dm_set_selinux_context.
We should set the SELinux context before the actual file system object creation.
The new dm_prepare_selinux_context function sets this using the selabel_lookup
fn in conjuction with the setfscreatecon fn. If selinux/label.h interface
(that should be a part of the selinux library) is not found during configure,
we fallback to the original matchpathcon function instead.
udev_sync feature requires semaphores (part of System V IPC) to be configured
in kernel (CONFIG_SYSVIPC). Check whether it is supported and if not, give
a warning message and disable udev synchronisation code automatically to
avoid any further error states and associated problems.
One should use the kernel with System V IPC support enabled or libdevmapper
with udev_sync feature disabled.
(with table provided).
This remove ioctl generates udev events like any other hence it needs to be
synchronized properly as well. Also, add dm task type in debug log when
setting a cookie (for better debugging).
This prevents some confusion when libudev was not found so udev_sync was disabled
automatically. Configure was successful though giving only a tiny warning.
Also, if "dmsetup udevcreatecookie" is used, never return 0x000000 as a result if
udev is not running and keep the output blank.
- add DM_UDEV_DISABLE_LIBRARY_FALLBACK udev flag to rely on udev only
- export dm_udev_create_cookie function to create new cookies on demand
- add --udevcookie, udevcreatecookie and udevreleasecookie for dmsetup
(to support "udev transactions" where one cookie value can be used for
several dmsetup calls)
- don't use DM_UDEV_DISABLE_CHECKING env. var. anymore and set the state
automatically (based on udev and libdevmapper dev path comparison)
Sometimes it is really needed to switch off udev checking and the warnings we show when
we detect that udev has not done its job right - the messages like "Udev should have done
this and that. Falling back to direct node creation/removal. " etc.
This would be especially handy while setting DM_DEV_DIR env var that could be set to a
different location than standard /dev (udev can't create nodes/symlinks out of that one
directory that is configured into udevd). The exact same situation happens while we're
running our tests.
This provides better support for environments where udev rules are installed
but udev_sync is not compiled in (however, using udev_sync is highly
recommended). It also provides consistent and expected functionality even
when '--noudevsync' option is used.
There is still requirement for kernel >= 2.6.31 for the flags to work though
(it uses DM cookies to pass the flags into the kernel and set them in udev
event environment that we can read in udev rules).
- we have these levels when the udev rules are processed:
10-dm.rules --> [11-dm-<subsystem>.rules] --> [12-dm-permissions.rules] -->
13-dm-disk.rules --> [...all the other foreign rules...] --> 95-dm-notify.rules
- each level can be disabled now by
DM_UDEV_DISABLE_{DM, SUBSYSTEM, DISK, OTHER}_RULES_FLAG
- add DM_UDEV_DISABLE_DM_RULES_FLAG to disable 10-dm.rules
- add DM_UDEV_DISABLE_OTHER_RULES_FLAG to disable all the other (non-dm) rules.
We cutoff these rules by using the 'last_rule', so this one should really be
used with great care and in well-founded situations. We use this for lvm's
hidden and layer devices now.
- add a parameter for add_dev_node, rm_dev_node and rename_dev_node so it's
possible to switch on/off udev checks
- use DM_UDEV_DISABLE_DM_RULES_FLAG and DM_UDEV_DISABLE_SUBSYSTEM_RULES_FLAG
if there's no cookie set and we have resume, remove and rename ioctl.
This could happen when someone uses the libdevmapper that is compiled with
udev_sync but the software does not make use of it. This way we can switch
off the rules and fallback to libdevmapper node creation so there's no
udev/libdevmapper race.
We don't have to call dm_cookie_supported with dm_udev_get_sync_support
this way. Also, it's necessary for the current code to work properly on
systems without cookie support (older kernels).
