IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
There were a couple of cases where lvresize, without --fs resize,
was resizing the crypt layer above the LV. Resizing the crypt
layer should only be done when fs resizing is enabled (even if the
fs is already small enough due to being independently reduced.)
Also, check the size of the crypt device to see if it's already
been reduced independently, and skip the cryptsetup resize if
it's not needed.
The recent change that verifies sys_serial system.devices entries
using the PVID did not exclude non-PV devices from being checked.
The verification code would attempt to use du->pvid which was null
for the non-PVs causing a segfault.
Since now we change deduplication with V4 table line change,
the modification tends to be faster and we can capture for a few ms
also 'status' about opening or closing deduplication index.
Use 'grep -E' to handle both words.
Handle multiple devices using the same serial number as
their device id. After matching devices to devices file
entries, if there is a discrepency between the ondisk PVID
and the devices file PVID, then rematch devices to
devices file entries using PVID, looking at all disks
on the system with the same serial number.
Place the addCleanup at the end as we don't want to go through clean up
if we don't make it through setUp. If we don't do this we can remove VGs
that we didn't create in the unit test.
If we plan to use dm throttling for mirror targets - we actually
have to check whether kernel runs with CONFIG_HZ_1000 - if it does
not the whole idea of throttling is actually not working in the
testsuite as within a single 'tick' with HZ 100 way too much date
is being moved on any modern hardware - and since there is no plan
to change this in kernel - we simply avoid using throttling on such
kernel and test needs to work differently - either ignore results
or use much larger mirror sizes...
We put this in to test one of the paths in the damon, but unfortunately
if we hit the race condition where the job actually is done we will try
to call j.Wait(1) after the remove. This fails with:
dbus.exceptions.DBusException: org.freedesktop.DBus.Error.UnknownMethod:
Method "Wait" with signature "i" on interface "com.redhat.lvmdbus1.Job"
doesn't exist
Which is caused by the dbus object no longer existing. We could handle
this, but the issue is we no longer have the ability to get the result to
return, they have been lost.
A better solution would be to write a specific unit test to force this code
path and handle all the possible outcomes.
These files are automatically cleared on reboot given
that /run is tmpfs, and that remains the primary way
of clearing online files.
But, if there's extreme use of vgcreate+pvscan+vgremove
between reboots, then removing online files in vgremove
will limit the number of unused online files using space
in /run.
The new option "--fs String" for lvresize/lvreduce/lvextend
controls the handling of file systems before/after resizing
the LV. --resizefs is the same as --fs resize.
The new option "--fsmode String" can be used to control
mounting and unmounting of the fs during resizing.
Possible --fs values:
checksize
Only applies to reducing size; does nothing for extend.
Check the fs size and reduce the LV if the fs is not using
the affected space, i.e. the fs does not need to be shrunk.
Fail the command without reducing the fs or LV if the fs is
using the affected space.
resize
Resize the fs using the fs-specific resize command.
This may include mounting, unmounting, or running fsck.
See --fsmode to control mounting behavior, and --nofsck to
disable fsck.
resize_fsadm
Use the old method of calling fsadm to handle the fs
(deprecated.) Warning: this option does not prevent lvreduce
from destroying file systems that are unmounted (or mounted
if prompts are skipped.)
ignore
Resize the LV without checking for or handling a file system.
Warning: using ignore when reducing the LV size may destroy the
file system.
Possible --fsmode values:
manage
Mount or unmount the fs as needed to resize the fs,
and attempt to restore the original mount state at the end.
nochange
Do not mount or unmount the fs. If mounting or unmounting
is required to resize the fs, then do not resize the fs or
the LV and fail the command.
offline
Unmount the fs if it is mounted, and resize the fs while it
is unmounted. If mounting is required to resize the fs,
then do not resize the fs or the LV and fail the command.
Notes on lvreduce:
When no --fs or --resizefs option is specified:
. lvextend default behavior is fs ignore.
. lvreduce default behavior is fs checksize
(includes activating the LV.)
With the exception of --fs resize_fsadm|ignore, lvreduce requires
the recent libblkid fields FSLASTBLOCK and FSBLOCKSIZE.
FSLASTBLOCK*FSBLOCKSIZE is the last byte used by the fs on the LV,
which determines if reducing the fs is necessary.
