IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The lvm fullreport works per VG and as such, the vg, lv, pv, seg and
pvseg subreport is done for each VG. However, if the PV is not part of
any VG yet, we still want to display pv and pvseg subreports for these
"orphan" PVs - so enable this for lvm fullreport's process_each_vg call.
This uses the vg->pv_write_list in place of the
vg->pvs_to_write list, and eliminates the use of
pvcreate_params. The label remove and zeroing
steps are shifted out of vg_write() to the higher
level like pvcreate will do.
The backup_restore_vg is used directly for restoring the VG from backup.
It's also used to do the VG conversions from one metadata format to
another which means vgconvert calls backup_restore_vg too.
When restoring VG from backup, we need to rewrite/write PV headers as
PVs may have been orphans before and now they're becoming part of some
VG - we need to write the PV_EXT_USED flag at least.
When using the backup_restore_vg for vgconvert, we need to write
completely new PV header in different format.
Avoid the special "pv_write" call and handling that was used before
this patch in vgconvert (vgconvert_single function to be more precise)
and reuse existing internal interface to register PV header for writing
(or rewriting) via vg->pvs_to_write list instead like we do it elsewhere
in the code.
This patch also resolves a problem in which PV headers with target
format were written in the vgconvert_single fn as orphans and VG
metadata were added later on - this was a tiny hack actually.
We can't do this now - we need to write the PV as belonging
to a VG because otherwise the PV_EXT_USED flag won't be written
properly (if the PV header is written as orphan, the PV_EXT_USED
is set to 0, of course, even though metadata are attached later).
So this patch removes this tiny inconsistency which was passing
just fine before because we didn't have any relation to the VG
in PV header before. Now we have the PV_EXT_USED flag which says
the "PV is used in some VG".
Pass the single vgname as a new process_each_vg arg
instead of setting a cmd flag to tell process_each_vg
to take only the first vgname arg from argv.
Other commands with different argv formats will be
able to use it this way.
This patch replaces "void *handle" with "struct processing_handle *handle"
in process_each_*, process_single_* and related functions.
The struct processing_handle consists of two handles inside now:
- the "struct selection_handle *selection_handle" used for
applying selection criteria while processing process_each_*,
process_single_* and related functions (patches using this
logic will follow)
- the "void* custom_handle" (this is actually the original handle
used before this patch - a pointer to custom data passed into
process_each_*, process_single_* and related functions).
For example, the old call and reference:
find_config_tree_str(cmd, "devices/dir", DEFAULT_DEV_DIR)
...now becomes:
find_config_tree_str(cmd, devices_dir_CFG)
So we're referring to the named configuration ID instead
of passing the configuration path and the default value
is taken from central config definition in config_settings.h
automatically.
To create an Embedding Area during PV creation (pvcreate or as part of
the vgconvert operation), we need to define the Embedding Area size.
The Embedding Area start will be calculated automatically by the tools.
This patch adds --embeddingareasize argument to pvcreate and vgconvert.
Accept -q as the short form of --quiet.
Suppress non-essential standard output if -q is given twice.
Treat log/silent in lvm.conf as equivalent to -qq.
Review all log_print messages and change some to
log_print_unless_silent.
When silent, the following commands still produce output:
dumpconfig, lvdisplay, lvmdiskscan, lvs, pvck, pvdisplay,
pvs, version, vgcfgrestore -l, vgdisplay, vgs.
[Needs checking.]
Non-essential messages are shifted from log level 4 to log level 5
for syslog and lvm2_log_fn purposes.
Move commod code to destroy orphan VG into free_orphan_vg() function.
Use orphan vgmem for creation of PV lists.
Remove some free_pv_fid() calls (FIXME: check all of them)
FIXME: Check whether we could merge release_vg back again for all VGs.
Since format instances will use own memory pool, it's necessary to properly
deallocate it. For now, only fid is deallocated. The PV structure itself
still uses cmd mempool mostly, but anytime we'd like to add a mempool
in the struct physical_volume, we can just rename this fn to free_pv and
add the code (like we have free_vg fn for VGs).
We allow writing non-orphan PVs only for resize now. The "orphan PV" assert
in pv_write fn uses the "allow_non_orphan" parameter to control this assert.
However, we should find a more elaborate solution so we can remove this
restriction altogether (pv_write together with vg_write is not atomic, we
need to find a safe mechanism so there's an easy revert possible in case of
an error).
Pass metadataignore through PV creation / setup paths.
As a result of this cleanup, we can remove the unnecessary setting
of mda_ignore bits inside pvcreate_single(), after call to pv_create.
For now, just set metadataignore to '0' in some places. This is
equivalent to the prior functionality, although the 0 is given
by the caller not hardcoded in _mda_setup() call.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Going forward, we would like to allow users to specify the total
number of metadatacopies in a VG rather than on a per-PV basis. In
order to facilitate that, introduce --pvmetadatacopes to replace
--metadatacopies everywhere. We still allow --metadatacopies for
pv commands, but require --pvmetadatacopies for vg commands.
Eventually we will introduce --vgmetadatacopies. Once we do that,
we should either deprecate --metadatacopies or make it a synonym based
on the command (pvmetadatacopies for pv commands, and vgmetadatacopies
for vg commands). The latter option would likely just require a simple
'strncpy' check against cmd->command->name to qualify the merge_synonym
call.
Update nightly tests to cover the pvmetadatacopies synonym.
Note that this patch is the result of an eariler review comment for
the implicit pvcreate patches. Should apply cleanly on top of the
implicit pvcreate patches (I applied after patch 10/10 in that series).
NOTE: This patch will require --pvmetadatacopies for vgconvert as
--metadatacopies is no longer accepted.
Remove the checks for vg_read_error() in most of the tools callback
functions and instead make the check in _process_one_vg() more general.
In all but vgcfgbackup, we do not want to proceed if we get any error
from vg_read(). In vgcfgbackup's case, we may proceed if the backup
is to proceed with inconsistent VGs. This is a special case though,
and we mark it with the READ_ALLOW_INCONSISTENT flag passed to
process_each_vg (and subsequently to _process_one_vg).
NOTE: More cleanup is needed in the vg_read_error() path cases.
This patch is a start.
Later patches should consolidate the vgremove / vgreduce functions but for
now let's clarify what vg_remove actually does by changing the name.
Author: Dave Wysochanski <dwysocha@redhat.com>
Adds pe_align_offset to 'struct physical_volume'; is initialized with
set_pe_align_offset(). After pe_start is established pe_align_offset is
added to it.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Sun May 3 12:32:30 CEST 2009 Petr Rockai <me@mornfall.net>
* Rework the toollib interface (process_each_*) on top of new vg_read.
Rebased 6/26/09 by Dave W.
- Add skipping message to process_each_lv
- Remove inconsistent_t.
Several commands calls process_each_vg() and in provided
callback it explicitly recovers VG if inconsistent.
(vgchange, vgconvert, vgscan)
It means that old VG is released and reread but the function
above (process_one_vg) tries to unlock and release old VG.
Patch moves the repair logic into _process_one_vg() function.
It always tries to read vg (even inconsistent) and then decides
what to do according new defined parameter.
Also patch unifies inconsistent error messages.
The only slight change if for vgremove command, where
it now tries to repair VG before it removes if force arg is given.
(It works similar way before, just the order of operation changed).
This patch is not fully tested and leaves some related bugs unfixed.
Intended behaviour of the code now:
pe_start in the lvm2 format PV label header is set only by pvcreate (or
vgconvert -M2) and then preserved in *all* operations thereafter.
In some specialist cases, after the PV is added to a VG, the pe_start
field in the VG metadata may hold a different value and if so, it
overrides the other one for as long as the PV is in such a VG.
Currently, the field storing the size of the data area in the PV label
header always holds 0. As it only has meaning in the context of a
volume group, it is calculated whenever the PV is added to a VG (and can
be derived from extent_size and pe_count in the VG metadata).
Fixes problem when after downconvert to lvm1 VG is broken:
# lvcreate -n lv1 -l 4 vg_test
Invalid LV in extent map (PV /dev/sdb1, PE 0, LV 0, LE 0)
...
