IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
If pvmove crashed and metadata contains pvmove LV
but without miorrored segments, pvmove --abort
will not repair the situation (and finish wth success!).
Fix it by allowing metadata update if aborting
(thus removing pvmove LV) even if no moved LVs detected.
(Tested on real metadata provided by an lvm user:-)
Add "devices/default_data_alignment" to lvm.conf to control the internal
default that LVM2 uses: 0==64k, 1==1MB, 2==2MB, etc.
If --dataalignment (or lvm.conf's "devices/data_alignment") is specified
then it is always used to align the start of the data area. This means
the md_chunk_alignment and data_alignment_detection are disabled if set.
(Same now applies to pvcreate --dataalignmentoffset, the specified value
will be used instead of the result from data_alignment_offset_detection)
set_pe_align() still looks to use the determined default alignment
(based on lvm.conf's default_data_alignment) if the default is a
multiple of the MD or topology detected values.
In all top vg read functions only LCK_VG_READ/WRITE can be used.
All other vg lock definitions are low-level backend machinery.
Moreover, LCK_WRITE cannot be tested through bitmask.
This patch fixes these mistakes.
For _recover_vg() we do not need lock_flags, it can be only
two of above and we always upgrading to LCK_VG_WRITE lock there.
(N.B. that code is racy)
There is no functional change in code (despite wrong masking
it produces correct bits:-)
One shiny day we should use libblkid here. But now using LUKS is
very common together with LVM and pvcreate destroys LUKS completely.
So for user's convenience, try to detect LUKS signature and allow abort.
This is not only undocumented but is is also in violation with --help
documentation.
Using --yes without --force is useful in pvcreate when it detects
old signature.
pvcreate detects MD and swap signature.
The logic hidden there is not only documented but it is also
user unfriendly. Who invented this logic should run pvcreate
on its own critical MD device to see why;-)
This patch
- creates one function instead of duplication code
- asks if user want to overwrite signature
- allows aborting (!)
(Please note that writing LVM signatute without wiping old
is wrong, it confuses blkid, MD will not work anyway and
swap and LUKS is broken too.)
The lvm repair issues I believe are the superficial symptoms of this
bug - there are worse issues that are not as clearly seen. From my
inline comments:
* If the mirror was successfully recovered, we want to always
* force every machine to write to all devices - otherwise,
* corruption will occur. Here's how:
* Node1 suffers a failure and marks a region out-of-sync
* Node2 attempts a write, gets by is_remote_recovering,
* and queries the sync status of the region - finding
* it out-of-sync.
* Node2 thinks the write should be a nosync write, but it
* hasn't suffered the drive failure that Node1 has yet.
* It then issues a generic_make_request directly to
* the primary image only - which is exactly the device
* that has suffered the failure.
* Node2 suffers a lost write - which completely bypasses the
* mirror layer because it had gone through generic_m_r.
* The file system will likely explode at this point due to
* I/O errors. If it wasn't the primary that failed, it is
* easily possible in this case to issue writes to just one
* of the remaining images - also leaving the mirror inconsistent.
*
* We let in_sync() return 1 in a cluster regardless of what is
* in the bitmap once recovery has successfully completed on a
* mirror. This ensures the mirroring code will continue to
* attempt to write to all mirror images. The worst that can
* happen for reads is that additional read attempts may be
* taken.
Ignore snapshots when performing mirror recovery beneath an origin.
Pass LCK_ORIGIN_ONLY flag around cluster.
Add suspend_lv_origin and resume_lv_origin using LCK_ORIGIN_ONLY.
DM devices were not handled properly on nodes in a cluster that were not
where the splitmirrors command was issued. This was happening because
suspend_lv/resume_lv were being used in a place where activate_lv should
have been used.
When the suspend/resume are issued on (effectively) new LVs, their
'resource' (UUID) is not located in the lv_hash. Thus, both operations
turn into no-ops. You can see this from the output of clvmd from one
of the remote nodes:
<snip>
do_suspend_lv, lock not already held
<snip>
do_resume_lv, lock not already held
'activate_lv' enjoins the other nodes in the cluster to process the lock
and activate the new LV. clvmd output from remote node as follows:
do_lock_lv: resource 'zMseY7CBuO3Ty09vXlplPAHzD0Y0CovjrTdv0R1VcwggMwPdYhutHErRcwm5Nd2S', cmd = 0x19 LCK_LV_ACTIVATE (READ|LV|NONBLOCK), flags = 0x84 (DMEVENTD_MONITOR ), memlock = 1
sync_lock: 'zMseY7CBuO3Ty09vXlplPAHzD0Y0CovjrTdv0R1VcwggMwPdYhutHErRcwm5Nd2S' mode:1 flags=1
sync_lock: returning lkid 27b0001
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Petr Rockai <prockai@redhat.com>
clvmd daemon itself does the right thing when invoked as non-root, by
returning 4.
The patch removes the use daemon function from
/etc/rc.d/init.d/functions that´s unnecessary and has th bad habit to
mask the return codes from the real daemon.
Add a simple and generic check to see if clvmd is executed by root or not.
Our stop/reload/restart paths in the init script are complex and not all
the tools involved in the process are guaranteed to return 4 if executed
by non-root against a process that´s running as root (for example kill
-TERM will return -1 and parsing the output to catch the error is
suboptimal at best).
https://bugzilla.redhat.com/show_bug.cgi?id=553381
The new standard in the storage industry is to default alignment of data
areas to 1MB. fdisk, parted, and mdadm have all been updated to this
default.
Update LVM to align the PV's data area start (pe_start) to 1MB. This
provides a more useful default than the previous default of 64K (which
generally ended up being a 192K pe_start once the first metadata area
was created).
Before this patch:
# pvs -o name,vg_mda_size,pe_start
PV VMdaSize 1st PE
/dev/sdd 188.00k 192.00k
After this patch:
# pvs -o name,vg_mda_size,pe_start
PV VMdaSize 1st PE
/dev/sdd 1020.00k 1.00m
The heuristic for setting the default alignment for LVM data areas is:
- If the default value (1MB) is a multiple of the detected alignment
then just use the default.
- Otherwise, use the detected value.
In practice this means we'll almost always use 1MB -- that is unless:
- the alignment was explicitly specified with --dataalignment
- or MD's full stripe width, or the {minimum,optimal}_io_size exceeds
1MB
- or the specified/detected value is not a power-of-2
Introduce --norestorefile to allow user to override the new requirement.
This can also be overridden with "devices/require_restorefile_with_uuid"
in lvm.conf -- however the default is 1.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
We can already detect MD devices internally. But when using MD partitions,
these have "block extended major" (blkext) assigned (259). Blkext major
is also used in general, so we need to check whether the original device
is an MD device actually.
An incorrect fix on July 13, 2010 for an annoyance has caused a regression.
The offending check-in was part of the 2.02.71 release of LVM. That
check-in caused any PVs specified on the command line to be ignored when
performing a mirror split.
This patch reverses the aforementioned check-in (solving the regressions)
and posits a new solution to the list reversal problem. The original
problem was that we would always take the lowest mimage LVs from a mirror
when performing a split, but what we really want is to take the highest
mimage LVs. This patch accomplishes that by working through the list in
reverse order - choosing the higher numbered mimages first. (This also
reduces the amount of processing necessary.)
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Takahiro Yasui <takahiro.yasui@hds.com>
corruption bug in cmirror. 'dm_bit' is only ever used as a boolean operation
within LVM, but it can return a range of values. If the bit is set, a power of
2 is returned. If the bit is unset, 0 is returned.
'log_test_bit' (a function in the cluster mirror log daemon code) has switched
to using the dm bit operations in rhel6. There are two places in the daemon
code where 'log_test_bit' is not used merely as a boolean, but rather the
return value is used as the return value for the log functions 'is_clean' and
'in_sync' - having assumed that 'dm_bit' was returning 0 or 1 only.
One place the 'in_sync' function is utilized is in 'dm_rh_get_state' - a
function that informs the mirroring code how to treat I/O and which devices to
read/write from. 'dm_rh_get_state' was checking if the return value of
'in_sync' was 1 to determine if the region was DM_RH_CLEAN. Since 'dm_bit'
(and by extension 'log_test_bit' and 'in_sync') was returning powers of 2,
DM_RH_CLEAN was rarely being reported as it should have been. Thinking the
region was out-of-sync, the mirroring code would write only to the primary
device. When the primary device was failed, all of those writes were lost -
leaving the entire mirror corrupted.
all but one mirror leg.
<patch header>
To handle a double failure of a mirrored log, Jon's two patches are
commited, however, lvconvert command can't still handle an error
when mirror leg and mirrored log got failure at the same time.
[Patch]: Handle both devices of a mirrored log failing (bug 607347)
posted: https://www.redhat.com/archives/lvm-devel/2010-July/msg00009.html
commit: https://www.redhat.com/archives/lvm-devel/2010-July/msg00027.html
[Patch]: Handle both devices of a mirrored log failing (bug 607347) -
additional fix
posted: https://www.redhat.com/archives/lvm-devel/2010-July/msg00093.html
commit: https://www.redhat.com/archives/lvm-devel/2010-July/msg00101.html
In the second patch, the target type of mirrored log is replaced with
error target when remove_log is set to 1, but this procedure should be
also used in other cases such as the number of mirror leg is 1. This
patch relocates the procedure to the main path.
In addition, I added following three changes.
- Removed tmp_orphan_lvs handling procedure
It seems that _delete_lv() can handle detached_log_lv properly
without adding mirror legs in mirrored log to tmp_orphan_lvs.
Therefore, I removed the procedure.
- Removed vg_write()/vg_commit()
Metadata is saved by vg_write()/vg_commit() just after detached_log_lv
is handled. Therefore, I removed vg_write()/vg_commit().
- With Jon's second patch, we think that we don't have to call
remove_mirror_log() in _lv_update_mirrored_log() because will be
handled remove_mirror_images() in _lvconvert_mirrors_repaire().
</patch header>
Signed-off-by: Takahiro Yasui <takahiro.yasui@hds.com>
Reviewed-by: Petr Rockai <prockai@redhat.com>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
The cluster log daemon (cmirrord) is not multi-threaded and
can handle only one request at a time. When a log is stacked
on top of a mirror (which itself contains a 'core' log), it
creates a situation that cannot be solved without threading.
When the top level mirror issues a "resume", the log daemon
attempts to read from the log device to retrieve the log
state. However, the log is a mirror which, before issuing
the read, attempts to determine the 'sync' status of the
region of the mirror which is to be read. This sync status
request cannot be completed by the daemon because it is
blocked on a read I/O to the very mirror requesting the
sync status.
With mirror_log_fault_policy of 'remove' and mirror_image_fault_policy
of 'allocate', the log type of the mirror volume is converted from
'disk' or 'mirrored' to 'core' when all mirror legs but one in a mirror
volume broke.
Keep new_log_count as a number of valid log devices by using log_count
variable for a temporary usage in the first phase of error recovery
in _lvconvert_mirrors_repair().
Signed-off-by: Takahiro Yasui <takahiro.yasui@hds.com>
Reviewed-by: Petr Rockai <prockai@redhat.com>
mirrors, we must also check that the log daemon (cmirrord) is running.
The log module can be auto-loaded, but the daemon cannot be
"auto-started". Failing to check for the daemon produces cryptic
messages that customers have a hard time deciphering. (The system
messages do report that the log daemon is not running, but people
don't seem to find this message easily.)
Here are examples of what is printed when the module is available,
but the log daemon has not been started.
[root@bp-01 LVM2]# lvcreate -m1 -l1 -n lv vg
Shared cluster mirrors are not available.
[root@bp-01 LVM2]# lvcreate -m1 -l1 -n lv vg -v
Setting logging type to disk
Finding volume group "vg"
Archiving volume group "vg" metadata (seqno 3).
Creating logical volume lv
Executing: /sbin/modprobe dm-log-userspace
Cluster mirror log daemon is not running
Shared cluster mirrors are not available.
Creating volume group backup "/etc/lvm/backup/vg" (seqno 4).
The main problem with these bugs was that the newly split
off LV was not being suspended properly. This meant that
the memlock count was not being balanced, the DM devices
were not being renamed, and some DM devices which should
have been removed were not.
I've also renamed some of the variables and added comments
to make things clearer as to what is going on. (I can break
this patch in two if it means easier review.)
Switch dmeventd to use dm_create_lockfile and drop duplicate code.
Allow clvmd pidfile to be configurable.
Switch cmirrord and clvmd to use dm_create_lockfile.
This should bring less confusion when there are some settings left and
people just forgot about it and then they run into problems. These messages
should give them a hint of what's really going on.
A previous check-in added logic to handle the case where both images
of a mirrored log failed. It solved the problem by simply removing
the log entirely - leaving the parent mirror with a 'core' log. This
worked for most cases. However, if there was a small delay between
the failures of the two mirrored log devices, the mirror would hang,
LVM would hang, and no additional LVM commands could be issued.
When the first leg of the log fails, it signals the need for repair.
Before 'lvconvert --repair' is run by dmeventd, the second leg fails.
'lvconvert' would see both devices as failed and try to remove the
log entirely. When it came time to suspend the parent mirror to
update the configuration, the suspend would hang because it couldn't
get any I/O through the mirrored log, which was plugged waiting for
corrective action. The solution is to replace the log with an error
target to clear any pending writes before removing it. This allows
the parent mirror to suspend and make the proper changes.
When using vgmetadatacopies value other than "umanaged" (0), prompt
the user if the usage of --metadataignore would change the value of
vgmetadatacopies. The main 2 cases are:
1) pvchange --metadataignore
2) vgextend --metadataignore
We leave the prompt check in the tools, and do not change anything
if the user says 'n'.
Examples:
vgextend --metadataignore y vgtest /dev/loop0
Setting metadataignore will override preferred number of copies of VG vgtest metadata.
Are you sure? [y/n]: y
No physical volume label read from /dev/loop0
Physical volume "/dev/loop0" successfully created
Volume group "vgtest" successfully extended
pvchange --metadataignore y /dev/loop3
Setting metadataignore on /dev/loop3 will override preferred number of copies of VG vgtest metadata.
Are you sure? [y/n]: y
WARNING: Changing preferred number of copies of VG vgtest metadata from 3 to 2
Physical volume "/dev/loop3" changed
1 physical volume changed / 0 physical volumes not changed
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
- If a PV contained empty mdas, the auto-recovery code was not kicking in.
- The 'inconsistent' state was getting lost when metadata was cached so
recovery didn't kick in. But leave the behaviour alone when using
precommitted metadata because of a warning in a confusing FIXME.
In my testing, pvs and vgs didn't repair inconsistent metadata like they
used to do. (How many other tools fail similarly now?)
And there should be no need to cache inconsistent metadata because it is
supposed to get repaired under the protection of a write lock immediately it is
discovered.
This code is in need of a redesign based on first principles.
I still see bugs in this code and this commit is risky.
Rather than attempting to remove all the images of a mirrored
log volume via remove_mirror_images, simply remove the log
if all its devices have failed.
Taka was the first to report that there is still an outstanding
issue with handling this case. I've managed to reproduce it
only very rarely, and am still working on identifying the problem.
Failing to handle the problem rarely is better than not handling
the scenario at all, so I'm checking this in.
Moreover, in current mirror handling, when it calls activate
on removed but suspended detached log this counter drops below zero
and confuses debug log.
The same region size is used for both mirror volume and mirrored
log volume, but when the physical extent size is bigger than region size,
the size of mirror leg for mirrored log is smaller than the region size
and lvcreate command fails.
This patch adjusts a region size of mirrored log to a smaller value of
region size or physical extent size.
[This patch ensures that the region_size of the mirrored log does not
exceed the size of the mirrored log itself, which would violate the
kernel constraint: (region_size <= ti->len).]
Signed-off-by: Takahiro Yasui <takahiro.yasui@hds.com>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Preload libc.mo file for localized lvm before taking memory lock - this way
we prevent disk access for some error paths in libdm, that prints localized
errno messages while they are still in memory locked state.
- s/Active clustred VG/clustered VG/ (only LV can be active)
- print only active LVs (not all) in status command
(In the lvdisplay form /dev/vg/lv.)
For now, still use awk (already used in clustered_vgs).
https://bugzilla.redhat.com/show_bug.cgi?id=598495
to 3-way mirror. When conversion operations are performed on
these types of mirrors, log options can be confused/ignored.
In the case of a converting 3-way mirror, we have a top-level
2-way corelog mirror whose legs are 1) a 2-way disk-log mirror
and 2) a linear device. If we wish to convert this 3-way mirror
to a 2-way mirror, the linear device is removed and the extra
top layer is eliminated. If we also wished to convert the disk
log to a core log in the same step, ambiguity creeps in. It is
somewhat obvious what the user wants - a 2-way mirror with a
corelog. However, looking at the top level mirror before
compression, it seems that the mirror already has a core log.
This is why the operation seemed to fail.
This patch simply re-evaluates what mirrored_seg points to after
a compression and then considers the log argument.
This is a fix for bug 599898.
Because execve stops the command loop,
we never receive response (only socket close) for clvmd -S,
so waiting for response here makes no sense.
But if the calling process (clvmd -S) exits too early, connection
is closed from client side, clvmd takes this as an error and
never run restart code.
Ugly hack(TM).
When using clustered mirrors, we need device nodes to be created during
processing of device tree, not at its end like we normally do (we need to
access the nodes in cmirror prematurely). Therefore we use a new flag called
"immediate_dev_node" stored in deptree's load_properties struct to instruct the
device tree processing code to immediately synchronize with udev and flush all
stacked node operations so the nodes are prepared for use.
For now, the immediate_dev_node is used for clustered mirrors during
processing the dm_tree_preload_children code only. We can add more later if
needed.
linux/kdev_t.h even though it wasn't needed. Strangely, it seems
to be causing problems on various architectures (i686) in the
function daemons/cmirrord/functions.c:disk_status_info()->sprintf.
I'm not sure why this is a problem since none of the macros in
kdev_t.h are used in that code, but it certainly doesn't hurt to
pull an unnecessary header and it seems to fix the problem.
Code is mixing up internal DLM and LVM definitions of lock
modes and flags.
OpenAIS and singlenode locking do not depend on DLM but
code currently cannot be compiled without libdlm.h!
LCK_* flags is LVM abstraction, used through all the code.
Only low-level backend (clvmd-cman etc) should use DLM definitions,
also this code should do all needed conversions.
Because there are two DLM flags used in generic code
(NOQUEUE, CONVERT) we define it similar way like lock modes.
(So all needed binary-compatible flags are on one place in locking.h)
(Further code cleaning still needed, though:-)
- allocate environment dynamically (still missing some limit?)
- try to recover, if destroy failed (do not destroy lvm here) and free memory
- check strdup() return codes
- report failure to log
- do not print NULL in exclusive lock loop
Activate only the first replicator-dev LV, that activates all other
related LVs from Replicator. In case of error during this activation,
it will not retry again for other heads (less confusing error log).
length(array) is specific to GNU awk and doesn't work in mawk.
Use a return value of "split" function to indicate array size, this is
supported in both gawk and mawk.
This patch fixes the following errors during "make install" when mawk is
installed as a default awk.
mawk: scripts/relpath.awk: line 25: illegal reference to array from
mawk: scripts/relpath.awk: line 25: illegal reference to array to
mawk: scripts/relpath.awk: line 27: illegal reference to array from
mawk: scripts/relpath.awk: line 32: illegal reference to array to
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Adding function _add_partial_replicator_to_dtree() to create
partial tree for Replicator target.
Using dm_tree_node_set_presuspend_node() for Replicator.
As for _process_one_vg() we need similar retry loop for
process_each_lv_in_vg(). This patch retries to process
failed LVs with reopened VGs.
Patch does not add any extra repeated invocations if there is not
found any missing VG during LV processing.
Patch modifes behavior of _process_one_vg().
In the first pass vg_read() collectis for replicator sorted list of
additional VGs during lock_vol().
If any other VG is needed by the replicator and it is not yet opened
then next iteration loop is taken with all collected VGs.
Flag vg->cmd_missing_vgs detects missing VGs.
Introduce struct cmd_vg to store information about needed
volume group name, vgid, flags and the pointer to opened VG.
Keep VGs list in alphabetical order for locking order.
Introduce functions:
cmd_vg_add() add new cmd_vg entry.
cmd_vg_lookup() search cmd_vgs for vg_name.
cmd_vg_read() open VGs in cmd_vgs list.
cmd_vg_release() close VGs in reversed order.
Adding configure.in support for Replicators.
Adding basic lib lvm support for Replicators.
Adding flags REPLICATOR and REPLICATOR_LOG.
Adding segments SEG_REPLICATOR and SEG_REPLICATOR_DEV.
Adding basic methods for handling replicator metadata.
For deactivation of Replicator check in advance that all heads
have open_count == 0. For this presuspend_node is used as all
head nodes are linking this control node.
Introducing dm_tree_node_set_presuspend_node() for presuspending child
node (i.e. replicator control target) before deactivation of parent node
(i.e. replicator-dev target).
This patch presents no functional change to current dtree - only
replicator target currently sets presuspend node for dev nodes.
Patch adds failed_lvnames to the list of parameters for process_each_lv_in_vg().
If the list is not NULL it will be filled with LV names of failing LVs
during function execution.
Application could later reiterate only on failed LVs.
are active mirrors or snapshots.
We don't have the mechanisms in place to change the device-mapper
tables for those targets that have behavioral differences between
cluster and single machine instances. Allowing users to change
the attribute but not changing the target's behavior can lead to
data corruption.
The following bugs are fixed/avoided by this patch:
235123 - vgchange -c [ny] do not change target types when necessary
289331 - RFE: switching from cluster domain to local domain needs to deactivate volume somehow
289541 - when changing from local to cluster, volumes can not appear to be deactivated
This should avoid various races between dmeventd on multiple nodes
in cluster where one node already repairing device and another
run full scan and locks the device.
the device cache file is dumped both in vgscan and clvmd process.
Unfortunately, clvmd calls lvmcache_label_scan,
it properly destroys persistent filter, but during
persistent_filter_dump it merges old cache content back!
This causes that change in filters is not properly propagated
into device cache after vgscan on cluster.
(Only new devices are added.)
https://bugzilla.redhat.com/show_bug.cgi?id=591861
Use Requires.private: instead of Libs.private:
Use UDEV_PC and SELINUX_PC for Require.private:
It looks like usage of Requires.private is prefered from Libs.private.
However pkg-config documentation is really poor here. But here is
short outcome:
There is a difference in Libs.private: and Requires.private: where
we specify libselinux instead of -lselinux -lsepol.
We leave resolving of query like 'pkg-config --libs --static devmapper'
on taking proper selinux and udev libs to their .pc files instead of
hardcoding them into our .pc file which is might give incorrect answer.
- i.e. dependency of libselinux package might change and we may return
wrong list of linked libraries.
http://bugs.freedesktop.org/show_bug.cgi?id=4738http://err.no/personal/blog/tech/2008-03-25-18-07_pkg-config,_sonames_and_Requires.private
A shortcut for --ignorelockingfailure, --ignoremonitoring, --poll n options
and LVM_SUPPRESS_LOCKING_FAILURE_MESSAGES environment variable used all at
once in initialisation scripts (e.g. rc.sysinit or initrd).
being able to remove more images from a mirror than the
number of PVs directly specified for removal.
The effort to fix bug 581611 corrected a bug that was unnoticed
at the time. The loop in _remove_mirror_images that looks over
the specified PVs was allowing devices that were previously
counted and moved to the end of the list to be double-counted.
This resulted in the number of devices needed for removal always
being satisfied - even if the user did not specify enough PVs
for removal to satisfy the request. When 581611 was fixed, this
double-counting no longer took place and the result was to remove
only the minimum of the number of PVs specified or the number
that was asked to be removed.
By simply always setting 'new_area_count' (as used to be done
only in the else statement), we return to the previous behavior.
Indeed, this is exactly what the double-counting was allowing
to happen before the fix of 581611.
Allow lv_remove_with_dependencies() to know the top-level LV that was
requested to be removed (otherwise it recurses and we lose context).
A merging snapshot cannot be removed directly but the associated origin
can be. Disallow removal of a merging snapshot unless the associated
origin is also being removed.
There's no need for foreign udev rules to touch LVM reserved devices
(snapshot, pvmove, _mlog, _mimage, _vorigin) even if they happen to
be visible. The same applies for /dev/disk content - no need to create
any content for these devices (and so no need to run any "blkid" etc.).
This also prevents setting any inotify "watch" from udev rules on such
devices that is a source of race conditions (the rules need to honor
DM_UDEV_DISABLE_OTHER_RULES_FLAG for this to work though).
This version number change reflects the memory handling change
for string-based pv/vg/lv string based attributes.
In addition, when adding support for tags, I forgot to increase
the version number.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
