IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Fix some interactions between device IDs and hints. Hints
may limit the scanned devices which should not always trigger
a search for the PVs that were intentionally not scanned.
Hints should also be invalidated if they contain a device
that's become excluded by an internal filter such as the
device_id filter.
Fix commit 847f1dd99c
"device_id: rewrite validation of devname entries"
which began calling device_ids_refresh() in cases where it
was unnecessary, leading to extra PV searches and warnings.
Specifically, a command like "lvs <vg>" would use the hints
file to scan only devices for the named VG. This means that
scanning other PVs would be skipped, and device IDs of those
PVs could not be validated because there are no PVID values
to verify. This missing info would cause messages about
the missing info, and would cause device_ids_refresh to
search for the PVs that had been intentionally skipped.
If the system changes, locate PVs that appear on different devices,
and update the device IDs in the devices file. A system change is
detected by saving the DMI product_uuid or hostname in the devices
file, and comparing it to the current system value. If a root PV
is restored or copied to a new system with different devices, then
the product_uuid or hostname should change, and trigger lvm to
locate PVIDs from system.devices on new devices.
With the recent use of DEVLINKS, there is no longer any real
point in checking the filter for symlink names. Removing
this check should not change behavior with or without symlinks
in the filter.
"vgchange -aay --autoactivation event" is called by our udev rule.
When the udev rule runs, symlinks for devices may not all be created
yet. If the regex filter contains symlinks, it won't work correctly.
This command uses devices that already passed through pvscan. Since
pvscan applies the regex filter correctly, this command inherits the
filtering from pvscan and can skip the regex filter itself.
See the previous commit
"pvscan: use alternate device names from DEVLINKS to check filter"
Change messages that refer to devices being "excluded by filters"
to say just "excluded". This will avoid mistaking the word
"filters" with the lvm.conf filter setting.
dev_name(dev) returns "[unknown]" if there are no names
on dev->aliases. It's meant mainly for log messages.
Many places assume a valid path name is returned, and
use it directly. A caller that wants to use the path
from dev_name() must first check if the dev has any
paths with dm_list_empty(&dev->aliases).
In a certain disconnected state, a block device is present on
the system, can be opened, reports a valid size, reports the
correct device id (wwid), and matches a devices file entry.
But, reading the device can still fail. In this case,
device_ids_validate() was misinterpreting the read error as
the device having no data/label on it (and no PVID).
The validate function would then clear the PVID from the
devices file entry for the device, thinking that it was
fixing the devices file (making it consistent with the on disk
state.) Fix this by not attempting to check and correct a
devices file entry that cannot be read. Also make this case
explicit in the hints validation code (which was doing the
right thing but indirectly.)
Since we check for present DM devices - cache result for
futher use of checking presence of such device.
lvm2 uses cache result for label scan, but also when
it tries to activate or deactivate LV - however only simple
target 'striped' is reasonably supported.
Use disable_dm_devs to be able to control when lv_info()
get cache or uncached results.
TODO: support more type, however this is getting very complicated.
If the optimized label scan fails (using online files),
then clear the device state prior to falling back to the
standard label_scan. This avoids printing output about
unexpected state.
Copy another optimization from pvscan -aay to vgchange -aay.
When using the optimized label scan for only one VG, acquire the
VG lock prior to the scan. This allows vg_read to then skip the
repeated label scan that normally happens after locking the vg.
Include the device name in the /run/lvm/pvs_online/pvid files.
Commands using the pvid file can use the devname to more quickly
find the correct device, vs finding the device using the
major:minor number. If the devname in the pvid file is missing
or incorrect, fall back to using the devno.
For completeness and consistency, adjust the behavior
for some variations of:
vgchange -aay --autoactivation event [vgname]
The current standard use is with a VG name arg, and the
command is only called when all pvs_online files exist.
This is the optimal case, in which only pvs_online devs
are read. This remains the same.
Clean up behaviors for some other unexpected uses of the
command:
. With no VG name arg, the command activates any VGs
that are complete according to pvs_online. If no
pvs_online files exist, it does nothing.
. If a VG name is used but no PVs online files exist for
the VG, or the PVs online files are incomplete, then
consider there could be a problem with the pvs_online
files, and fall back to a full label scan prior to
attempting the activation.
Part of the optimization to avoid a full dev_cache_scan requires
translating major:minor numbers to a device name. If this devno
translation fails, then fall back to doing a full dev_cache_scan
which is slower but certain to provide the info. This preserves
the most important part of the label scanning optimization in the
vgchange aay (avoiding dev_cache_scan is a relatively small part
of the optimized activation compared to label scanning.)
Port another optimization from pvscan -aay to vgchange -aay:
"pvscan: only add device args to dev cache"
This optimization avoids doing a full dev_cache_scan, and
instead populates dev-cache with only the devices in the
VG being activated.
This involves shifting the use of pvs_online files from
the hints interface up to the higher level label_scan
interface. This specialized label_scan is structured
around creating a list of devices from the pvs_online
files. Previously, a list of all devices was created
first, and then reduced based on the pvs_online files.
The initial step of listing all devices was slow when
thousands of devices are present on the system.
This optimization extends the previous optimization that
used pvs_online files to limit the devices that were
actually scanned (i.e. reading to identify the device):
"vgchange -aay: optimize device scan using pvs_online files"
The information in /run/lvm/pvs_online/<pvid> files can
be used to build a list of devices for a given VG.
The pvscan -aay command has long used this information to
activate a VG while scanning only devices in that VG, which
is an important optimization for autoactivation.
This patch implements the same thing through the existing
device hints interface, so that the optimization can be
applied elsewhere. A future patch will take advantage of
this optimization in vgchange -aay, which is now used in
place of pvscan -aay for event activation.
Reporting non-PVs / "all devices" is only done by
pvs -a or pvdisplay -a, so avoid the work managing
a list of all devices in process_each_pv.
In the case when it's needed, use the results of
label_scan which already determines which devs
are not PVs.
pvid and vgid are sometimes a null-terminated string, and
other times a 'struct id', and the two types were often
cast between each other. When a struct id was cast to a char
pointer, the resulting string would not necessarily be null
terminated. Casting a null-terminated string id to a
struct id is fine, but is still avoided when possible.
A struct id is: int8_t uuid[ID_LEN]
A string id is: char pvid[ID_LEN + 1]
A convention is introduced to help distinguish them:
- variables and struct fields named "pvid" or "vgid"
should be null-terminated strings.
- variables and struct fields named "pv_id" or "vg_id"
should be struct id's.
- examples:
char pvid[ID_LEN + 1];
char vgid[ID_LEN + 1];
struct id pv_id;
struct id vg_id;
Function names also attempt to follow this convention.
Avoid casting between the two types as much as possible,
with limited exceptions when known to be safe and clearly
commented.
Avoid using variations of strcpy and strcmp, and instead
use memcpy/memcmp with ID_LEN (with similar limited
exceptions possible.)
If label_scan encounters bad vg metadata, invalidate
bcache data for the device and reread the mda_header
and metadata text back to back. With concurrent commands
modifying large metadata, it's possible that the entire
metadata area can be rewritten in the time between a
command reading the mda_header and reading the metadata
text that the header points to. Since the label_scan
is just assembling an initial overview of devices, it
doesn't use locking to serialize with other commands
that may be modifying the vg metadata at the same time.
error reading dev and no pvid on dev were both
returning 0. make it easier for callers to
know which, if they care.
return 1 if the device could be read, regardless
of whether a pvid was found or not.
set has_pvid=1 if a pvid is found and 0 if no
pvid is found.
When 'lv_info()' is called with &info structure,
the presence of node has to be checked from this structure.
Without this we were needlesly trying to look out 0:0 device.
The LVM devices file lists devices that lvm can use. The default
file is /etc/lvm/devices/system.devices, and the lvmdevices(8)
command is used to add or remove device entries. If the file
does not exist, or if lvm.conf includes use_devicesfile=0, then
lvm will not use a devices file. When the devices file is in use,
the regex filter is not used, and the filter settings in lvm.conf
or on the command line are ignored.
LVM records devices in the devices file using hardware-specific
IDs, such as the WWID, and attempts to use subsystem-specific
IDs for virtual device types. These device IDs are also written
in the VG metadata. When no hardware or virtual ID is available,
lvm falls back using the unstable device name as the device ID.
When devnames are used, lvm performs extra scanning to find
devices if their devname changes, e.g. after reboot.
When proper device IDs are used, an lvm command will not look
at devices outside the devices file, but when devnames are used
as a fallback, lvm will scan devices outside the devices file
to locate PVs on renamed devices. A config setting
search_for_devnames can be used to control the scanning for
renamed devname entries.
Related to the devices file, the new command option
--devices <devnames> allows a list of devices to be specified for
the command to use, overriding the devices file. The listed
devices act as a sort of devices file in terms of limiting which
devices lvm will see and use. Devices that are not listed will
appear to be missing to the lvm command.
Multiple devices files can be kept in /etc/lvm/devices, which
allows lvm to be used with different sets of devices, e.g.
system devices do not need to be exposed to a specific application,
and the application can use lvm on its own set of devices that are
not exposed to the system. The option --devicesfile <filename> is
used to select the devices file to use with the command. Without
the option set, the default system devices file is used.
Setting --devicesfile "" causes lvm to not use a devices file.
An existing, empty devices file means lvm will see no devices.
The new command vgimportdevices adds PVs from a VG to the devices
file and updates the VG metadata to include the device IDs.
vgimportdevices -a will import all VGs into the system devices file.
LVM commands run by dmeventd not use a devices file by default,
and will look at all devices on the system. A devices file can
be created for dmeventd (/etc/lvm/devices/dmeventd.devices) If
this file exists, lvm commands run by dmeventd will use it.
Internal implementaion:
- device_ids_read - read the devices file
. add struct dev_use (du) to cmd->use_devices for each devices file entry
- dev_cache_scan - get /dev entries
. add struct device (dev) to dev_cache for each device on the system
- device_ids_match - match devices file entries to /dev entries
. match each du on cmd->use_devices to a dev in dev_cache, using device ID
. on match, set du->dev, dev->id, dev->flags MATCHED_USE_ID
- label_scan - read lvm headers and metadata from devices
. filters are applied, those that do not need data from the device
. filter-deviceid skips devs without MATCHED_USE_ID, i.e.
skips /dev entries that are not listed in the devices file
. read lvm label from dev
. filters are applied, those that use data from the device
. read lvm metadata from dev
. add info/vginfo structs for PVs/VGs (info is "lvmcache")
- device_ids_find_renamed_devs - handle devices with unstable devname ID
where devname changed
. this step only needed when devs do not have proper device IDs,
and their dev names change, e.g. after reboot sdb becomes sdc.
. detect incorrect match because PVID in the devices file entry
does not match the PVID found when the device was read above
. undo incorrect match between du and dev above
. search system devices for new location of PVID
. update devices file with new devnames for PVIDs on renamed devices
. label_scan the renamed devs
- continue with command processing
Fix clearing persistent filter state when clearing all
the state from a label_scan.
label_scan reads devs and saves info in bcache, lvmcache,
and in the persistent filter. In some uncommon cases, an
lvm command wants to clear all info from a prior label_scan,
and repeat label_scan from scratch. In these cases, info
in lvmcache, bcache and the persistent filter all need to
be cleared before repeating label_scan.
By missing the persistent filter wiping, outdated persistent
filter info, from a prior label_scan, could cause lvm to
incorrectly filter devices that change between polling intervals.
(i.e. if the device changes in such a way that the filtering
results change.)
A case where lvm wants to do multiple label_scans is a
polling command (like lvconvert --merge), when lvmpolld
has been disabled, so that the command itself needs to
to do repeated polling checks.
Move extra md component detection into the label scan phase.
It had been in set_pv_devices which was deep within the vg_read
phase, which wasn't a good place (better to detect that earlier.)
Now that pv metadata info is available in the scan phase, the pv
details (size and device_hint) can be used for extra md checking.
Use the device_hint from the pv metadata to trigger a full md
component check if the device_hint begins with /dev/md.
Stop triggering full md component checks based on missing
udev info for a dev.
Changes to tests to reflect that the code is now detecting
md components in some test case that it wasn't before.
The args for pvcreate/pvremove (and vgcreate/vgextend
when applicable) were not efficiently opened, scanned,
and filtered. This change reorganizes the opening
and filtering in the following steps:
- label scan and filter all devs
. open ro
. standard label scan at the start of command
- label scan and filter dev args
. open ro
. uses full md component check
. typically the first scan and filter of pvcreate devs
- close and reopen dev args
. open rw and excl
- repeat label scan and filter dev args
. using reopened rw excl fd
- wipe and write new headers
. using reopened rw excl fd
To read the lvm headers and set dev->pvid if the
device is a PV. Difference from label_scan_ functions
is this does not read any vg metadata or add any info
to lvmcache.
Filtering in label_scan was controlled indirectly by
the fact that bcache was not yet set up when label_scan
first ran. The result is that filters that needed data
would not run and would return -EAGAIN, which would
result in the dev flag FILTER_AFTER_SCAN being set.
After the dev header was read for checking the label,
filters would be rechecked because of FILTER_AFTER_SCAN.
All filters would be checked this time because bcache
was now set up, and the filters needing data would
largely use data already scanned for reading the label.
This design worked but is hard to adjust for future
cases where bcache is already set up.
Replace this method (based on setting up bcache, or not)
with a new cmd flag filter_nodata_only. When this flag
is set filters that need data will not run. This allows
the same label_scan behavior when bcache has been set up.
There are no expected changes in behavior.
