IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Unconditionally guard there is at least 1/4 of metadata volume
free (<16Mib) or 4MiB - whichever value is smaller.
In case there is not enough free space do not let operation proceed and
recommend thin-pool metadata resize (in case user has not
enabled autoresize, manual 'lvextend --poolmetadatasize' is needed).
When update fails in suspend() (sending of messages
fails because metadata space is full) call resume(),
so the locking sequence works properly for clustering.
Also failing deactivation should unlock memory.
Since plugin's percentage compare has been fixed,
it's now revealed wrong compare here.
The logic for threshold is - to allow to go as high
as given value e.g. 80% - so if pool is exactlu 80%
full it's still allowed to use it (dmeventd will not
resize it).
Revert back to already existing behavior which has been slightly
modified by a900d150e4.
At the end however it seem to be equal to change TID right with first
metadata write.
Existing code missed handling for 'unused' thin-pool which would
require to also check empty message list for TID==0.
So with the fix we now again preserve 'active' thin-pool volume
when first thin volume is created - this property was lost and caused
problems in cluster, where the lock was hold, but volume was no longer
active on the node.
Another missing part was the proper support for already increased,
but unfinished TID change.
So going back here with existing logic -
TID is increased with first MDA update.
Code allows start with either same TID or (TID-1).
If there are messages, TID must be lower by 1 for sending,
otherwise messages were already posted.
Existing messaging intarface for thin-pool has a few 'weak' points:
* Message were posted with each 'resume' operation, thus not allowing
activation of thin-pool with the existing state.
* Acceleration skipped suspend step has not worked in cluster,
since clvmd resumes only nodes which are suspended (have proper lock
state).
* Resume may fail and code is not really designed to 'fail' in this
phase (generic rule here is resume DOES NOT fail unless something serious
is wrong and lvm2 tool usually doesn't handle recovery path in this case.)
* Full thin-pool suspend happened, when taken a thin-volume snapshot.
With this patch the new method relocates message passing into suspend
state.
This has a few drawbacks with current API, but overal it performs
better and gives are more posibilities to deal with errors.
Patch introduces a new logic for 'origin-only' suspend of thin-pool and
this also relates to thin-volume when taking snapshot.
When suspend_origin_only operation is invoked on a pool with
queued messages then only those messages are posted to thin-pool and
actual suspend of thin pool and data and metadata volume is skipped.
This makes taking a snapshot of thin-volume lighter operation and
avoids blocking of other unrelated active thin volumes.
Also fail now happens in 'suspend' state where the 'Fail' is more expected
and it is better handled through error paths.
Activation of thin-pool is now not sending any message and leaves upto a tool
to decided later how to finish unfinished double-commit transaction.
Problem which needs some API improvements relates to the lvm2 tree
construction. For the suspend tree we do not add target table line
into the tree, but only a device is inserted into a tree.
Current mechanism to attach messages for thin-pool requires the libdm
to know about thin-pool target, so lvm2 currently takes assumption, node
is really a thin-pool and fills in the table line for this node (which
should be ensured by the PRELOAD phase, but it's a misuse of internal API)
we would possibly need to be able to attach message to 'any' node.
Other thing to notice - current messaging interface in thin-pool
target requires to suspend thin volume origin first and then send
a create message, but this could not have any 'nice' solution on lvm2
side and IMHO we should introduce something like 'create_after_resume'
message.
Patch also changes the moment, where lvm2 transaction id is increased.
Now it happens only after successful finish of kernel transaction id
change. This change was needed to handle properly activation of pool,
which is in the middle of unfinished transaction, and also this corrects
usage of thin-pool by external apps like Docker.
With thin-pool kernel target module 1.13 it's now support usage of
external origin with sizes which are not 'alligned' with chunk size
of thin-pool.
Enable lvm2 support for this and also fix reporting of data_percent
usage for case sizes are not alligned.
When chunk size needs to be estimated, the code missed to round
to proper 64kb boundaries (or power of 2 for older thin pool driver).
So for some data and metadata size (i.e. 10GB and 4MB) it resulted
in incorrect chunk size (not being a multiple of 64KB)
Fix it by adding proper rounding and also use 1 routine for 2 places
where the same calculation is made.
Fix also incorrect printed warning that has used 'ffs()'
(which returns first 'least significant' bit in word)
and it was not really giving any useful size info and replace it
with properly estimated chunk size.
Fixing problem, when user sets volume_list and excludes thin pools
from activation. In this case pool return 'success' for skipped activation.
We need to really check the volume it is actually active to properly
to remove queued pool messages. Otherwise the lvm2 and kernel
metadata started to go async since lvm2 believed, messages were submitted.
Add also better check for threshold when create a new thin volume.
In this case we require local activation of thin pool so we are able
to check pool fullness.
The lv_layout and lv_type fields together help with LV identification.
We can do basic identification using the lv_attr field which provides
very condensed view. In contrast to that, the new lv_layout and lv_type
fields provide more detialed information on exact layout and type used
for LVs.
For top-level LVs which are pure types not combined with any
other LV types, the lv_layout value is equal to lv_type value.
For non-top-level LVs which may be combined with other types,
the lv_layout describes the underlying layout used, while the
lv_type describes the use/type/usage of the LV.
These two new fields are both string lists so selection (-S/--select)
criteria can be defined using the list operators easily:
[] for strict matching
{} for subset matching.
For example, let's consider this:
$ lvs -a -o name,vg_name,lv_attr,layout,type
LV VG Attr Layout Type
[lvol1_pmspare] vg ewi------- linear metadata,pool,spare
pool vg twi-a-tz-- pool,thin pool,thin
[pool_tdata] vg rwi-aor--- level10,raid data,pool,thin
[pool_tdata_rimage_0] vg iwi-aor--- linear image,raid
[pool_tdata_rimage_1] vg iwi-aor--- linear image,raid
[pool_tdata_rimage_2] vg iwi-aor--- linear image,raid
[pool_tdata_rimage_3] vg iwi-aor--- linear image,raid
[pool_tdata_rmeta_0] vg ewi-aor--- linear metadata,raid
[pool_tdata_rmeta_1] vg ewi-aor--- linear metadata,raid
[pool_tdata_rmeta_2] vg ewi-aor--- linear metadata,raid
[pool_tdata_rmeta_3] vg ewi-aor--- linear metadata,raid
[pool_tmeta] vg ewi-aor--- level1,raid metadata,pool,thin
[pool_tmeta_rimage_0] vg iwi-aor--- linear image,raid
[pool_tmeta_rimage_1] vg iwi-aor--- linear image,raid
[pool_tmeta_rmeta_0] vg ewi-aor--- linear metadata,raid
[pool_tmeta_rmeta_1] vg ewi-aor--- linear metadata,raid
thin_snap1 vg Vwi---tz-k thin snapshot,thin
thin_snap2 vg Vwi---tz-k thin snapshot,thin
thin_vol1 vg Vwi-a-tz-- thin thin
thin_vol2 vg Vwi-a-tz-- thin multiple,origin,thin
Which is a situation with thin pool, thin volumes and thin snapshots.
We can see internal 'pool_tdata' volume that makes up thin pool has
actually a level10 raid layout and the internal 'pool_tmeta' has
level1 raid layout. Also, we can see that 'thin_snap1' and 'thin_snap2'
are both thin snapshots while 'thin_vol1' is thin origin (having
multiple snapshots).
Such reporting scheme provides much better base for selection criteria
in addition to providing more detailed information, for example:
$ lvs -a -o name,vg_name,lv_attr,layout,type -S 'type=metadata'
LV VG Attr Layout Type
[lvol1_pmspare] vg ewi------- linear metadata,pool,spare
[pool_tdata_rmeta_0] vg ewi-aor--- linear metadata,raid
[pool_tdata_rmeta_1] vg ewi-aor--- linear metadata,raid
[pool_tdata_rmeta_2] vg ewi-aor--- linear metadata,raid
[pool_tdata_rmeta_3] vg ewi-aor--- linear metadata,raid
[pool_tmeta] vg ewi-aor--- level1,raid metadata,pool,thin
[pool_tmeta_rmeta_0] vg ewi-aor--- linear metadata,raid
[pool_tmeta_rmeta_1] vg ewi-aor--- linear metadata,raid
(selected all LVs which are related to metadata of any type)
lvs -a -o name,vg_name,lv_attr,layout,type -S 'type={metadata,thin}'
LV VG Attr Layout Type
[pool_tmeta] vg ewi-aor--- level1,raid metadata,pool,thin
(selected all LVs which hold metadata related to thin)
lvs -a -o name,vg_name,lv_attr,layout,type -S 'type={thin,snapshot}'
LV VG Attr Layout Type
thin_snap1 vg Vwi---tz-k thin snapshot,thin
thin_snap2 vg Vwi---tz-k thin snapshot,thin
(selected all LVs which are thin snapshots)
lvs -a -o name,vg_name,lv_attr,layout,type -S 'layout=raid'
LV VG Attr Layout Type
[pool_tdata] vg rwi-aor--- level10,raid data,pool,thin
[pool_tmeta] vg ewi-aor--- level1,raid metadata,pool,thin
(selected all LVs with raid layout, any raid layout)
lvs -a -o name,vg_name,lv_attr,layout,type -S 'layout={raid,level1}'
LV VG Attr Layout Type
[pool_tmeta] vg ewi-aor--- level1,raid metadata,pool,thin
(selected all LVs with raid level1 layout exactly)
And so on...
Fix get_pool_params to only read params.
Add poolmetadataspare option to get_pool_params.
Move all profile code into update_pool_params.
Move recalculate code into pool_manip.c
Since vg_name inside /lib function has already been ignored mostly
except for a few debug prints - make it and official internal API
feature.
vg_name is used only in /tools while the VG is not yet openned,
and when lvresize/lvcreate /lib function is called with VG pointer
already being used, then vg_name becomes irrelevant (it's not been
validated anyway).
So any internal user of lvcreate_params and lvresize_params does not
need to set vg_name pointer and may leave it NULL.
When creating pool's metadata - create initial LV for clearing with some
generic name and after the volume is create & cleared - rename it to
reserved name '_tmeta/_cmeta'.
We should not expose 'reserved' names for public LVs.
When pool_has_message() is queried with NULL lv and 0 device_id
it should just return 'true' when there is any message queued.
So it needs to return negative value dm_list_empty().
Since there is no user for this code path in code currently,
this bug has not been triggered.
The allocation/thin_pool_chunk_size is a bit more complex. It's default
value is evaluated in runtime based on selected thin_pool_chunk_size_policy.
But the value is just a starting point. The calculation then continues
with dependency on the properties of the devices used. Which means for
such a default value, we know only the starting value.
Several fixes for the recent changes that treat allocation percentages
as upper limits.
Improve messages to make it easier to see what is happening.
Fix some cases that failed with errors when they didn't need to.
Fix crashes when first_seg() returns NULL.
Remove a couple of log_errors that were actually debugging messages.
Introduce a new parameter called "approx_alloc" that is set when the
desired size of a new LV is specified in percentage terms. If set,
the allocation code tries to get as much space as it can but does not
fail if can at least get some.
One of the practical implications is that users can now specify 100%FREE
when creating RAID LVs, like this:
~> lvcreate --type raid5 -i 2 -l 100%FREE -n lv vg
Avoid use of external origin with size unaligned/incompatible with
thin pool chunk size, since the last chunk is not correctly provisioned
when it is overwritten.
Functions that handle set-up, tear-down and creation of thin pool
volumes will be more generally applicable when more targets exist
that make use of device-mapper's persistent data format. One of
these targets is the dm-cache target. I've selected some functions
that will be useful for the cache segment type to be moved, since
they will no longer be thin pool specific but are more broadly
useful to any segment type that makes use of a 'pool' LV.
