IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Native disk scanning is now both reduced and
async/parallel, which makes it comparable in
performance (and often faster) when compared
to lvm using lvmetad.
Autoactivation now uses local temp files to record
online PVs, and no longer requires lvmetad.
There should be no apparent command-level change
in behavior.
When lvmetad is not used, use temporary files to record
which PVs have appeared. Use these temp files to determine
when a VG is complete, to trigger autoactivation.
This change allows us to remove lvmetad while keeping the
same autoactivation behavior that lvmetad provides.
The temp files are created in /run/lvm/pvs_online/ and are
named for the PVID of the PV. The files contain the
major:minor of the device the PV was read from.
e.g. if VG foo has dev1 and dev2, then:
. pvscan --cache -aay dev1
reads vg metadata from dev1
creates /run/lvm/pvs_online/<pvid-of-dev1>
checks if all vg->pvs are online: no
. pvscan --cache -aay dev2
reads vg metadata from dev2
creates /run/lvm/pvs_online/<pvid-of-dev2>
checks if all vg->pvs are online: yes
autoactivates vg
A 'pvscan --cache dev' (without -aay) still records that
dev is online.
A 'pvscan --cache --major X --minor Y' after a device is
gone will remove the temp file for it.
A 'pvscan --cache [-aay]' (no devs) resets the state of
temp files by removing them all, then scanning all devs
and creating temp files for PVs that are found.
If no online files exist, the first pvscan --cache scans
all devs and creates temp files for any PVs found.
The scope of the temp files is only pvscan, and they are only
used for pvscan-based autoactivation. No other commands are
concerned with or aware of these temp files. When lvm creates
or removes PVs, no attempt is made to update the temp files.
The md filter can operate in two native modes:
- normal: reads only the start of each device
- full: reads both the start and end of each device
md 1.0 devices place the superblock at the end of the device,
so components of this version will only be identified and
excluded when lvm uses the full md filter.
Previously, the full md filter was only used in commands
that could write to the device. Now, the full md filter
is also applied when there is an md 1.0 device present
on the system. This means the 'pvs' command can avoid
displaying md 1.0 components (at the cost of doubling
the i/o to every device on the system.)
(The md filter can operate in a third mode, using udev,
but this is disabled by default because there have been
problems with reliability of the info returned from udev.)
A few places were calling a function to check if a
VG lock was held. The only place it was actually
needed is for pvcreate which wants to do its own
locking (and scanning) around process_each_pv.
The locking/scanning exceptions for pvcreate in
process_each_pv/vg_read can be enabled by just passing
a couple of flags instead of checking if the VG is
already locked. This also means that these special
cases won't be enabled unknowingly in other places
where they shouldn't be used.
Four commands lock two VGs at a time:
- vgsplit and vgmerge already have their own logic to
acquire the locks in the correct order.
- vgimportclone and vgrename disable this ordering check.
We have been warning about duplicate devices (and disabling lvmetad)
immediately when the dup was detected (during label_scan). Move the
warnings (and the disabling) to happen later, after label_scan is
finished.
This lets us avoid an unwanted warning message about duplicates
in the special case were md components are eliminated during the
duplicate device resolution.
As we start refactoring the code to break dependencies (see doc/refactoring.txt),
I want us to use full paths in the includes (eg, #include "base/data-struct/list.h").
This makes it more obvious when we're breaking abstraction boundaries, eg, including a file in
metadata/ from base/
md devices using an older superblock version have
superblocks at the end of the md device. For commands
that skip reading the end of devices during filtering,
the md component devs will be scanned, and will appear
as duplicate PVs to the original md device. Remove
these md components from the list of unused duplicate
devices, so they are treated as if they had been
ignored during filtering. This avoids the restrictions
that are placed on using PVs with duplicates.
Filters are still applied before any device reading or
the label scan, but any filter checks that want to read
the device are skipped and the device is flagged.
After bcache is populated, but before lvm looks for
devices (i.e. before label scan), the filters are
reapplied to the devices that were flagged above.
The filters will then find the data they need in
bcache.
The clvmd saved_vg data is independent from the normal lvm
lvmcache vginfo data, so separate saved_vg from vginfo.
Normal lvm doesn't need to use save_vg at all, and in clvmd,
lvmcache changes on vginfo can be made without worrying
about unwanted effects on saved_vg.
To avoid the chance of freeing a saved vg while another
code path is using it, defer freeing saved vgs until
all the lvmcache content is dropped for the vg.
There are likely more bits of code that can be removed,
e.g. lvm1/pool-specific bits of code that were identified
using FMT flags.
The vgconvert command can likely be reduced further.
The lvm1-specific config settings should probably have
some other fields set for proper deprecation.
In some pvmove tests, clvmd uses the new (precommitted)
saved_vg, but then requests the old saved_vg, and
expects that the new saved_vg be returned instead of
the old. So, when returning the new saved_vg, forget
the old one so we don't return it again.
The filters save information about devices that should
be ignored, so if we need to repeat a scan (unusual,
but happens in clvmd), we need to update the filters.
After reading a VG, stash it in lvmcache as "saved_vg".
Before reading the VG again, try to use the saved_vg.
The saved_vg is dropped on VG lock operations.
The copy of the VG which clvmd stashes in lvmcache should
not only be used between suspend and resume, but between
sequential LV operations in clvmd, so that clvmd does not
need to reread the VG for each one. Prepare for that by
renaming the stashed VG as "saved_vg".
For reporting commands (pvs,vgs,lvs,pvdisplay,vgdisplay,lvdisplay)
we do not need to repeat the label scan of devices in vg_read if
they all had matching metadata in the initial label scan. The
data read by label scan can just be reused for the vg_read.
This cuts the amount of device i/o in half, from two reads of
each device to one. We have to be careful to avoid repairing
the VG if we've skipped rescanning. (The VG repair code is very
poor, and will be redone soon.)
Recent changes allow some major simplification of the way
lvmcache works and is used. lvmcache_label_scan is now
called in a controlled fashion at the start of commands,
and not via various unpredictable side effects. Remove
various calls to it from other places. lvmcache_label_scan
should not be called from anywhere during a command, because
it produces an incorrect representation of PVs with no MDAs,
and misclassifies them as orphans. This has been a long
standing problem. The invalid flag and rescanning based on
that is no longer used and removed. The 'force' variation is
no longer needed and removed.
Create a new dev->bcache_fd that the scanning code owns
and is in charge of opening/closing. This prevents other
parts of lvm code (which do various open/close) from
interfering with the bcache fd. A number of dev_open
and dev_close are removed from the reading path since
the read path now uses the bcache.
With that in place, open(O_EXCL) for pvcreate/pvremove
can then be fixed. That wouldn't work previously because
of other open fds.
The copy of VG metadata stored in lvmcache was not being used
in general. It pretended to be a generic VG metadata cache,
but was not being used except for clvmd activation. There
it was used to avoid reading from disk while devices were
suspended, i.e. in resume.
This removes the code that attempted to make this look
like a generic metadata cache, and replaces with with
something narrowly targetted to what it's actually used for.
This is a way of passing the VG from suspend to resume in
clvmd. Since in the case of clvmd one caller can't simply
pass the same VG to both suspend and resume, suspend needs
to stash the VG somewhere that resume can grab it from.
(resume doesn't want to read it from disk since devices
are suspended.) The lvmcache vginfo struct is used as a
convenient place to stash the VG to pass it from suspend
to resume, even though it isn't related to the lvmcache
or vginfo. These suspended_vg* vginfo fields should
not be used or touched anywhere else, they are only to
be used for passing the VG data from suspend to resume
in clvmd. The VG data being passed between suspend and
resume is never modified, and will only exist in the
brief period between suspend and resume in clvmd.
suspend has both old (current) and new (precommitted)
copies of the VG metadata. It stashes both of these in
the vginfo prior to suspending devices. When vg_commit
is successful, it sets a flag in vginfo as before,
signaling the transition from old to new metadata.
resume grabs the VG stashed by suspend. If the vg_commit
happened, it grabs the new VG, and if the vg_commit didn't
happen it grabs the old VG. The VG is then used to resume
LVs.
This isolates clvmd-specific code and usage from the
normal lvm vg_read code, making the code simpler and
the behavior easier to verify.
Sequence of operations:
- lv_suspend() has both vg_old and vg_new
and stashes a copy of each onto the vginfo:
lvmcache_save_suspended_vg(vg_old);
lvmcache_save_suspended_vg(vg_new);
- vg_commit() happens, which causes all clvmd
instances to call lvmcache_commit_metadata(vg).
A flag is set in the vginfo indicating the
transition from the old to new VG:
vginfo->suspended_vg_committed = 1;
- lv_resume() needs either vg_old or vg_new
to use in resuming LVs. It doesn't want to
read the VG from disk since devices are
suspended, so it gets the VG stashed by
lv_suspend:
vg = lvmcache_get_suspended_vg(vgid);
If the vg_commit did not happen, suspended_vg_committed
will not be set, and in this case, lvmcache_get_suspended_vg()
will return the old VG instead of the new VG, and it will
resume LVs based on the old metadata.
When process_each_pv() calls vg_read() on the orphan VG, the
internal implementation was doing an unnecessary
lvmcache_label_scan() and two unnecessary label_read() calls
on each orphan. Some of those unnecessary label scans/reads
would sometimes be skipped due to caching, but the code was
always doing at least one unnecessary read on each orphan.
The common format_text case was also unecessarily calling into
the format-specific pv_read() function which actually did nothing.
By analyzing each case in which vg_read() was being called on
the orphan VG, we can say that all of the label scans/reads
in vg_read_orphans are unnecessary:
1. reporting commands: the information saved in lvmcache by
the original label scan can be reported. There is no advantage
to repeating the label scan on the orphans a second time before
reporting it.
2. pvcreate/vgcreate/vgextend: these all share a common
implementation in pvcreate_each_device(). That function
already rescans labels after acquiring the orphan VG lock,
which ensures that the command is using valid lvmcache
information.
