IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Rename dev_read() to dev_read_buf() - the function that reads data
into a supplied buffer.
Introduce a new dev_read() that allocates the buffer it returns and
switch the important users over to this. No caller may change the
returned data. (For now, callers are responsible for freeing it after
use, but later the device layer will take full ownership.)
dev_read_buf() should only be used for tiny buffers or unimportant code
(such as the old disk formats).
The creation of wrapped around metadata - where the start of metadata is
written up to the end of the buffer and the remainder follows back at
the start of the buffer - is now restricted to cases where writing the
metadata in one piece wouldn't fit. This shouldn't happen in 'normal'
usage so let's begin treating the code for this as a special case that
can be ignored when optimising 'normal' cases.
Mark the first metadata area on each text format PV as MDA_PRIMARY.
Pass this information down to the device layer so that when
there are two metadata areas on a block device, we can easily
distinguish two independent streams of I/O.
Introduce enum dev_io_reason to categorise block device I/O
in debug messages so it's obvious what it is for.
DEV_IO_SIGNATURES /* Scanning device signatures */
DEV_IO_LABEL /* LVM PV disk label */
DEV_IO_MDA_HEADER /* Text format metadata area header */
DEV_IO_MDA_CONTENT /* Text format metadata area content */
DEV_IO_FMT1 /* Original LVM1 metadata format */
DEV_IO_POOL /* Pool metadata format */
DEV_IO_LV /* Content written to an LV */
DEV_IO_LOG /* Logging messages */
vgsplit shares the vg_rename code so that must only set the PV_MOVED_VG
flag introduced in commit 486ed10848
("vgmerge: Fix intermediate metadata corruption") on PVs that moved.
API for strtod() or strtoul() needs reset of errno, before it's being
called. So add missing resets in missing places and some also some
errno validation for out-of-range numbers.
Basically code moving operation to have a single place resolving
thin_pool_chunk_size_policy.
Supported are generic & performance profiles.
Function is now shared between thin manipulation code and configuration
_CFG logic to obtain defaults and handle correct reporting upward coding
stack.
Introduce 'hard limit' for max number of cache chunks.
When cache target operates with too many chunks (>10e6).
When user is aware of related possible troubles he
may increase the limit in lvm.conf.
Also verbosely inform user about possible solution.
Code works for both lvcreate and lvconvert.
Lvconvert fully supports change of chunk_size when caching LV
(and validates for compatible settings).
Some settings are not suitable for override in interactive/shell
mode because such settings may confuse the code and it may end
up with unexpected behaviour. This is because of the fact that
once we're in the interactive/shell mode, we have already applied
some settings for the shell itself and we can't override them
further because we're already using those settings to drive the
interactive/shell mode. Such settings would get ignored silently
or, in worse case, they would mess up the existing configuration.
Just for convenience to display all new configuration settings
introduced since given version (before, there was only --atversion
to display settings introduced in concrete version).
For example:
$ lvmconfig --type new --sinceversion 2.2.120
allocation {
# cache_mode="writethrough"
# cache_settings {
# }
}
global {
use_lvmlockd=0
# lvmlockd_lock_retries=3
# sanlock_lv_extend=256
use_lvmpolld=1
}
activation {
}
# report {
# compact_output_cols=""
# time_format="%Y-%m-%d %T %z"
# }
local {
# host_id=0
}
Here Coverity cannot see the pointer cannot be NULL in this
code path - opened coverity case #00531860.
We could make a model to avoid seeing related reports,
but then we loose coverage for modeled function.
So decided to add minor hint for this case.
Before printing a commented automatic config value,
print a line describing what it is. Otherwise, the
commented value can look like it's a part of an
example preceding it.
Move code which runtime detects settings for cache_policy
out of config dir to cache seg handling code.
Also mark cache_mode as command profilable setting.
Add new profilable configurables:
allocation/cache_policy
allocation/cache_settings
and mark allocation/cache_pool_chunk_size as profilable as well.
Obsolete allocation/cache_pool_cachemode and
introduce new allocation/cache_mode instead.
Rename DEFAULT_CACHE_POOL_POLICY to DEFAULT_CACHE_POLICY.
The CFG_SECTION_NO_CHECK flag can be used to mark a section
and its whole subtree as containing settings where checks
won't be made (lvmconfig --validate).
These are setting where we don't know the names and and type
in advance and they're recognized in runtime. As we don't know
the type and name in advance, we can't do any checks here
of course.
Use this flag with great care as it disables config checks
for the whole config subtree found under such section.
This flag is going to be used by subsequent patches from
Zdenek to support some cache settings...
Commit 7e728fe1a1 added a log call
directly in find_config_tree_array when defaults are used.
This patch also adds the log for the value which is found in
existing configuration and for which defaults are not used.
For example:
Defaults used:
config/config.c:1428 devices/scan not found in config: defaulting to scan = [ "/dev" ]
Value defined in configuration used:
config/config.c:1431 Setting devices/scan to scan = [ "/dev", "/mydev", "/abc" ]
This makes the logging consistent with the other find_config_tree_* functions.
Before, we used general find_config_tree_node function to retrieve
array values. This had a downside where if the node was not found,
we had to insert default values directly in-situ after the
find_config_tree_node call. This way, we had two copies of default
values - one in config_settings.h and the other one directly in the
code where we found out that find_config_tree_node returned NULL and
hence we needed to fall back to defaults.
With separate find_config_tree_array used for array config values,
we keep all the defaults centrally in config_settings.h because
the new find_config_tree_array automatically returns these defaults
if it can't find any value set in the configuration.
This patch just makes the behaviour exactly the same for arrays as
for any other non-array type where we call find_config_tree_<type>
already, hence making the internal interface for handling array
values consistent with the rest of the config types.
Do not display settings with undefined default values, but do display
these settings in case the value is defined directly in any part of
the existing config cascade.
For example, the lvmconfig --type current always displays these settings
(as it's somewhere in "current" configuration cascade that makes it defined).
The lvmconfig --type full displays these settings only if it's defined
somewhere in the cascade, but not if default value is used instead
The lvmconfig --type default never displays these settings...
More concrete example - let's have activation/volume_list directly
set in lvm.conf and activation/read_only_volume_list not set.
Both of these settings have *undefined default* values.
$lvmconfig --type full activation/volume_list activation/read_only_volume_list
volume_list="/dev/vg/lv"
(...only volume_list is defined, hence it's printed)
However, the comments will display more info (see also previous commit):
$lvmconfig --type full activation/volume_list activation/read_only_volume_list --withsummary
# Configuration option activation/volume_list.
# Only LVs selected by this list are activated.
# This configuration option does not have a default value defined.
# Value defined in existing configuration has been used for this setting.
volume_list="/dev/vg/lv"
# Configuration option activation/read_only_volume_list.
# LVs in this list are activated in read-only mode.
# This configuration option does not have a default value defined.
Display comment abour value from existing config being used. For example:
$ lvmconfig --type full --withsummary report/compact_output report/buffered
# Configuration option report/compact_output.
# Do not print empty report fields.
# Value defined in existing configuration has been used for this setting.
compact_output=1
# Configuration option report/buffered.
# Buffer report output.
buffered=1
The lvmconfig --type full is actually a combination of --type current
and --type missing together with --mergedconfig options used.
The overall outcome is a configuration tree with settings as LVM sees
it when it looks for the values - that means, if the setting is defined
in some config source (lvm.conf, --config, lvmlocal.conf or any profile
that is used), the setting is used. Otherwise, if the setting is not
defined in any part of the config cascade, the defaults are used.
The --type full displays exactly this final tree with all the values
defined, either coming from configuration tree or from defaults.
We shouldn't be adding spaces by default in output as that
may be be used already in scripts and especially for the eval
in shell scripts where spaces are not allowed between key
and value!
Add --withspaces option to lvmconfig for pretty output with
more space in for readability.
There are two basic groups of formatting flags (32 bits):
- common ones applicable for all config value types (lower 16 bits)
- type-related formatting flags (higher 16 bits)
With this patch, we initially support four new flags that
modify the the way the config value is displayed:
Common flags:
=============
DM_CONFIG_VALUE_FMT_COMMON_ARRAY - causes array config values
to be enclosed in "[ ]" even if there's only one item
(previously, there was no way to recognize an array with one
item and scalar value, hence array values with one member
were always displayed without "[ ]" which libdm accepted
when reading, but it may have been misleading for users)
DM_CONFIG_VALUE_FMT_COMMON_EXTRA_SPACE - causes extra spaces to
be inserted in "key = value" (or key = [ value, value, ... ] in
case of arrays), compared to "key=value" seen on output before.
This makes the output more readable for users.
Type-related flags:
===================
DM_CONFIG_VALUE_FMT_INT_OCTAL - prints integers in octal form with
"0" as a prefix (libdm's config reading code can handle this via
strtol just fine so it's properly recognized as number in octal
form already if there's "0" used as prefix)
DM_CONFIG_VALUE_FMT_STRING_NO_QUOTES - makes it possible to print
strings without enclosing " "
This patch also adds dm_config_value_set_format_flags and
dm_config_value_get_format_flags functions to set and get
these formatting flags.
This patch adds supporting code for handling deprecated settings.
Deprecated settings are not displayed by default in lvmconfig output
(except for --type current and --type diff). There's a new
"--showdeprecated" lvmconfig option to display them if needed.
Also, when using lvmconfig --withcomments, the comments with info
about deprecation are displayed for deprecated settings and with
lvmconfig --withversions, the version in which the setting was
deprecated is displayed in addition to the version of introduction.
If using --atversion with a version that is lower than the one
in which the setting was deprecated, the setting is then considered
as not deprecated (simply because at that version it was not
deprecated).
For example:
$ lvmconfig --type default activation
activation {
...
raid_region_size=512
...
}
$ lvmconfig --type default activation --showdeprecated
activation {
...
mirror_region_size=512
raid_region_size=512
...
}
$ lvmconfig --type default activation --showdeprecated --withversions
activation {
...
# Available since version 1.0.0.
# Deprecated since version 2.2.99.
mirror_region_size=512
# Available since version 2.2.99.
raid_region_size=512
...
}
$ lvmconfig --type default activation --showdeprecated --withcomments
activation {
...
# Configuration option activation/mirror_region_size.
# This has been replaced by the activation/raid_region_size
# setting.
# Size (in KB) of each copy operation when mirroring.
# This configuration option is deprecated.
mirror_region_size=512
# Configuration option activation/raid_region_size.
# Size in KiB of each raid or mirror synchronization region.
# For raid or mirror segment types, this is the amount of
# data that is copied at once when initializing, or moved
# at once by pvmove.
raid_region_size=512
...
}
$ lvmconfig --type default activation --withcomments --atversion 2.2.98
activation {
...
# Configuration option activation/mirror_region_size.
# Size (in KB) of each copy operation when mirroring.
mirror_region_size=512
...
}
A preparatory code for marking configuration nodes as deprecated:
- struct cfg_def_item gains 2 new fields ("deprecated_since_version" and "deprecation_comment"
- cfg* macros to handle new fields
- related config_settings.h edits to add new fields for each item (null for all at the moment)
Patch with implementation will follow...
Before this patch:
$ lvmconfig --type list --withversions --withsummary global/use_lvmetad
global/use_lvmetad - Use lvmetad to cache metadata and reduce disk scanning. [2.2.93]
$ lvmconfig --type list --withversions global/use_lvmetad
global/use_lvmetad
With this patch applied:
$ lvmconfig --type list --withversions --withsummary global/use_lvmetad
global/use_lvmetad - Use lvmetad to cache metadata and reduce disk scanning. [2.2.93]
$ lvmconfig --type list --withversions global/use_lvmetad
global/use_lvmetad - [2.2.93]
We're commenting out settings with undefined default values.
The comment character '#' was printed at the very beginning of
the line, it should be placed just at the beginning of the setting,
after the space/tab prefix is printed.
Before this patch:
$ lvmconfig --type default activation
activation {
...
# volume_list=[]
...
}
With this patch applied:
$ lvmconfig --type default activation
activation {
...
# volume_list=[]
...
}
These settings are in the "unsupported" group:
devices/loopfiles
log/activate_file
metadata/disk_areas (section)
metadata/disk_areas/<disk_area> (section)
metadata/disk_areas/<disk_area>/size
metadata/disk_areas/<disk_area>/id
These settings are in the "advanced" group:
devices/dir
devices/scan
devices/types
global/proc
activation/missing_stripe_filler
activation/mlock_filter
metadata/pvmetadatacopies
metadata/pvmetadataignore
metadata/stripesize
metadata/dirs
Also, this patch causes the --ignoreunsupported and --ignoreadvanced
switches to be honoured for all config types (lvmconfig --type).
By default, the --type current and --type diff display unsupported
settings, the other types ignore them - this patch also introduces
--showunsupported switch for all these other types to display even
unsupported settings in their output if needed.
lvmconfig --type list displays plain list of configuration settings.
Some of the existing decorations can be used (--withsummary and
--withversions) as well as existing options/switches (--ignoreadvanced,
--ignoreunsupported, --ignorelocal, --atversion).
For example (displaying only "config" section so the list is not long):
$lvmconfig --type list config
config/checks
config/abort_on_errors
config/profile_dir
$ lvmconfig --type list --withsummary config
config/checks - If enabled, any LVM configuration mismatch is reported.
config/abort_on_errors - Abort the LVM process if a configuration mismatch is found.
config/profile_dir - Directory where LVM looks for configuration profiles.
$ lvmconfig -l config
config/checks - If enabled, any LVM configuration mismatch is reported.
config/abort_on_errors - Abort the LVM process if a configuration mismatch is found.
config/profile_dir - Directory where LVM looks for configuration profiles.
$ lvmconfig --type list --withsummary --withversions config
config/checks - If enabled, any LVM configuration mismatch is reported. [2.2.99]
config/abort_on_errors - Abort the LVM process if a configuration mismatch is found. [2.2.99]
config/profile_dir - Directory where LVM looks for configuration profiles. [2.2.99]
Example with --atversion (displaying global section):
$ lvmconfig --type list global
global/umask
global/test
global/units
global/si_unit_consistency
global/suffix
global/activation
global/fallback_to_lvm1
global/format
global/format_libraries
global/segment_libraries
global/proc
global/etc
global/locking_type
global/wait_for_locks
global/fallback_to_clustered_locking
global/fallback_to_local_locking
global/locking_dir
global/prioritise_write_locks
global/library_dir
global/locking_library
global/abort_on_internal_errors
global/detect_internal_vg_cache_corruption
global/metadata_read_only
global/mirror_segtype_default
global/raid10_segtype_default
global/sparse_segtype_default
global/lvdisplay_shows_full_device_path
global/use_lvmetad
global/thin_check_executable
global/thin_dump_executable
global/thin_repair_executable
global/thin_check_options
global/thin_repair_options
global/thin_disabled_features
global/cache_check_executable
global/cache_dump_executable
global/cache_repair_executable
global/cache_check_options
global/cache_repair_options
global/system_id_source
global/system_id_file
$ lvmconfig --type list global --atversion 2.2.50
global/umask
global/test
global/units
global/suffix
global/activation
global/fallback_to_lvm1
global/format
global/format_libraries
global/segment_libraries
global/proc
global/locking_type
global/wait_for_locks
global/fallback_to_clustered_locking
global/fallback_to_local_locking
global/locking_dir
global/library_dir
global/locking_library
The settings which have their default value evaluated in runtime should
have their 'unconfigured' counterparts also evaluated in runtime since
those values can be constructed by using other settings.
For example, before this patch:
$ lvm dumpconfig --type default --unconfigured devices/cache_dir devices/cache
cache_dir="@DEFAULT_SYS_DIR@/@DEFAULT_CACHE_SUBDIR@"
cache="/etc/lvm/cache/.cache
With this patch applied:
$ lvm dumpconfig --type default --unconfigured devices/cache_dir devices/cache
cache_dir="@DEFAULT_SYS_DIR@/@DEFAULT_CACHE_SUBDIR@"
cache="@DEFAULT_SYS_DIR@/@DEFAULT_CACHE_SUBDIR@/.cache"
The @something@ used for unconfigured default value is not bound to
CFG_TYPE_STRING settings defined in config_settings.h, it can be
used for any other config type too.
