IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The RAID plug-in for dmeventd now calls 'lvconvert --repair' to address failures
of devices in a RAID logical volume. The action taken can be either to "warn"
or "allocate" a new device from any spares that may be available in the
volume group. The action is designated by setting 'raid_fault_policy' in
lvm.conf - the default being "warn".
LVM metadata knows only of striped segments - not linear ones.
The activation code detects segments with a single stripe and switches
them to use the linear target.
If the new lvm.conf setting is set to 0 (e.g. in a test script), this
'optimisation' is turned off.
Add filter which tries to check if scanned device is part
of active multipath.
Firstly, only SCSI major number devices are handled in filter.
Then it checks if device has exactly one holder (in sysfs) and
if it is device-mapper device and DM-UUID is prefixed by "MPATH-".
If so, this device is filtered out.
The whole filter can be switched off by setting
mpath_component_detection in lvm.conf.
https://bugzilla.redhat.com/show_bug.cgi?id=597010
Signed-off-by: Milan Broz <mbroz@redhat.com>
Go with just 64KiB for stack.
Closer inspection should be made, whether we actually need to play with
settings at all.
Since default stack size is 8MB and gets mapped via page locking thus,
it seems there is no big help with preallocation of stack to some value.
Add config option to enable crc checking of VG structures.
Currently it's disabled by default.
For the internal test-suite this check it is enabled.
Note: In the case the internal error is detected, debug build with
compile option DEBUG_ENFORCE_POOL_LOCKING helps to catch the source
of the problem.
Implementation described in doc/lvm2-raid.txt.
Basic support includes:
- ability to create RAID 1/4/5/6 arrays
- ability to delete RAID arrays
- ability to display RAID arrays
Notable missing features (not included in this patch):
- ability to clean-up/repair failures
- ability to convert RAID segment types
- ability to monitor RAID segment types
We've used udev fallback code till now to check whether udev
created/removed the entries in /dev correctly and if not,
a repair was done (giving a warning messagea about that).
This patch adds a possibility to enable this additional check
and subsequent fallback only when required (debugging purposes
mostly) and trust udev completely.
So let's disable the fallback code by default and add a new
configuration option "activation/udev_fallback".
(The original code for creating the nodes will still be used
in case the device directory that is set in lvm.conf differs
from the one that udev uses and also when activation/udev_rules
is set to 0 - otherwise we would end up with no nodes/symlinks
at all)
Also, add a new 'obtain_device_list_from_udev' setting to lvm.conf with which
we can turn this feature on or off if needed.
If set, the cache of block device nodes with all associated symlinks
will be constructed out of the existing udev database content.
This avoids using and opening any inapplicable non-block devices or
subdirectories found in the device directory. This setting is applied
to udev-managed device directory only, other directories will be scanned
fully. LVM2 needs to be compiled with udev support for this setting to
take effect. N.B. Any device node or symlink not managed by udev in
udev directory will be ignored with this setting on.
pv_manip.c to properly account for case when pe_start=0 and the first
physical extent is to be released (currently skip the first extent to
avoid discarding the PV label).
There is a lot to test.
Two new config settings added that are intended to make the code behave
closely to the way it did before - worth a try if you find problems.
Add configurable option to define minimal size of
of block device usable as a PV.
pv_min_size() is added to lvm-globals and it's being
initialized through _process_config.
Macro PV_MIN_SIZE is unused and removed.
New define DEFAULT_PV_MIN_SIZE_KB is added to lvm-global
and unlike PV_MIN_SIZE it uses KB units.
Should help users with various slow devices attached to the system,
which cannot be easily filtered out (like FDD on /dev/sdX):
https://bugzilla.redhat.com/show_bug.cgi?id=644578
to lvm.conf in the activation section: 'snapshot_autoextend_threshold' and
'snapshot_autoextend_percent', that define how to handle automatic snapshot
extension. The former defines when the snapshot should be extended: when its
space usage exceeds this many percent. The latter defines how much extra space
should be allocated for the snapshot, in percent of its current size.
Add "devices/default_data_alignment" to lvm.conf to control the internal
default that LVM2 uses: 0==64k, 1==1MB, 2==2MB, etc.
If --dataalignment (or lvm.conf's "devices/data_alignment") is specified
then it is always used to align the start of the data area. This means
the md_chunk_alignment and data_alignment_detection are disabled if set.
(Same now applies to pvcreate --dataalignmentoffset, the specified value
will be used instead of the result from data_alignment_offset_detection)
set_pe_align() still looks to use the determined default alignment
(based on lvm.conf's default_data_alignment) if the default is a
multiple of the MD or topology detected values.
The new standard in the storage industry is to default alignment of data
areas to 1MB. fdisk, parted, and mdadm have all been updated to this
default.
Update LVM to align the PV's data area start (pe_start) to 1MB. This
provides a more useful default than the previous default of 64K (which
generally ended up being a 192K pe_start once the first metadata area
was created).
Before this patch:
# pvs -o name,vg_mda_size,pe_start
PV VMdaSize 1st PE
/dev/sdd 188.00k 192.00k
After this patch:
# pvs -o name,vg_mda_size,pe_start
PV VMdaSize 1st PE
/dev/sdd 1020.00k 1.00m
The heuristic for setting the default alignment for LVM data areas is:
- If the default value (1MB) is a multiple of the detected alignment
then just use the default.
- Otherwise, use the detected value.
In practice this means we'll almost always use 1MB -- that is unless:
- the alignment was explicitly specified with --dataalignment
- or MD's full stripe width, or the {minimum,optimal}_io_size exceeds
1MB
- or the specified/detected value is not a power-of-2
Introduce --norestorefile to allow user to override the new requirement.
This can also be overridden with "devices/require_restorefile_with_uuid"
in lvm.conf -- however the default is 1.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Update example.conf to describe vgmetadatacopies. Provide an
explanation for the '0' ("unmanaged") value.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
