IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Do this at two levels, although one would be enough to
fix the problem seen recently:
- Ignore any reported sector size other than 512 of 4096.
If either sector size (physical or logical) is reported
as 512, then use 512. If neither are reported as 512,
and one or the other is reported as 4096, then use 4096.
If neither is reported as either 512 or 4096, then use 512.
- When rounding up a limited write in bcache to be a multiple
of the sector size, check that the resulting write size is
not larger than the bcache block itself. (This shouldn't
happen if the sector size is 512 or 4096.)
If udev info is missing for a device, (which would indicate
if it's an MD component), then do an end-of-device read to
check if a PV is an MD component. (This is skipped when
using hints since we already know devs in hints are good.)
A new config setting md_component_checks can be used to
disable the additional end-of-device MD checks, or to
always enable end-of-device MD checks.
When both hints and udev info are disabled/unavailable,
the end of PVs will now be scanned by default. If md
devices with end-of-device superblocks are not being
used, the extra I/O overhead can be avoided by setting
md_component_checks="start".
Save the list of PVs in /run/lvm/hints. These hints
are used to reduce scanning in a number of commands
to only the PVs on the system, or only the PVs in a
requested VG (rather than all devices on the system.)
udev creates a train wreck of events if we open devices
with RDWR. Until we can fix/disable/scrap udev, work around
this by opening RDONLY and then closing/reopening RDWR when
a write is needed. This invalidates the bcache blocks for
the device before writing so it can trigger unnecessary
rereading.
We have been warning about duplicate devices (and disabling lvmetad)
immediately when the dup was detected (during label_scan). Move the
warnings (and the disabling) to happen later, after label_scan is
finished.
This lets us avoid an unwanted warning message about duplicates
in the special case were md components are eliminated during the
duplicate device resolution.
As we start refactoring the code to break dependencies (see doc/refactoring.txt),
I want us to use full paths in the includes (eg, #include "base/data-struct/list.h").
This makes it more obvious when we're breaking abstraction boundaries, eg, including a file in
metadata/ from base/
Filters are still applied before any device reading or
the label scan, but any filter checks that want to read
the device are skipped and the device is flagged.
After bcache is populated, but before lvm looks for
devices (i.e. before label scan), the filters are
reapplied to the devices that were flagged above.
The filters will then find the data they need in
bcache.
Create a new dev->bcache_fd that the scanning code owns
and is in charge of opening/closing. This prevents other
parts of lvm code (which do various open/close) from
interfering with the bcache fd. A number of dev_open
and dev_close are removed from the reading path since
the read path now uses the bcache.
With that in place, open(O_EXCL) for pvcreate/pvremove
can then be fixed. That wouldn't work previously because
of other open fds.
New label_scan function populates bcache for each device
on the system.
The two read paths are updated to get data from bcache.
The bcache is not yet used for writing. bcache blocks
for a device are invalidated when the device is written.
Callers that read larger amounts of data now get a pointer to read-only
data directly without copying it through an intermediate buffer. This
data is owned by the device layer so the callers no longer free it.
If it obtains the data, it passes it into the supplied callback function
and returns 1. Otherwise the callback receives failed = 1.
Updated config_file_read_fd to use this and similarly return the data
via a callback fn of its own.
Rename dev_read() to dev_read_buf() - the function that reads data
into a supplied buffer.
Introduce a new dev_read() that allocates the buffer it returns and
switch the important users over to this. No caller may change the
returned data. (For now, callers are responsible for freeing it after
use, but later the device layer will take full ownership.)
dev_read_buf() should only be used for tiny buffers or unimportant code
(such as the old disk formats).
Mark the first metadata area on each text format PV as MDA_PRIMARY.
Pass this information down to the device layer so that when
there are two metadata areas on a block device, we can easily
distinguish two independent streams of I/O.
Introduce enum dev_io_reason to categorise block device I/O
in debug messages so it's obvious what it is for.
DEV_IO_SIGNATURES /* Scanning device signatures */
DEV_IO_LABEL /* LVM PV disk label */
DEV_IO_MDA_HEADER /* Text format metadata area header */
DEV_IO_MDA_CONTENT /* Text format metadata area content */
DEV_IO_FMT1 /* Original LVM1 metadata format */
DEV_IO_POOL /* Pool metadata format */
DEV_IO_LV /* Content written to an LV */
DEV_IO_LOG /* Logging messages */
It's possible for an LVM LV to use a device during activation which
then differs from device which LVM assumes based on metadata later on.
For example, such device mismatch can occur if LVM doesn't have
complete view of devices during activation or if filters are
misbehaving or they're incorrectly set during activation.
This patch adds code that can detect this mismatch by creating
VG UUID and LV UUID index while scanning devices for device cache.
The VG UUID index maps VG UUID to a device list. Each device in the
list has a device layered above as a holder which is an LVM LV device
and for which we know the VG UUID (and similarly for LV UUID index).
We can acquire VG and LV UUID by reading /sys/block/<dm_dev_name>/dm/uuid.
So these indices represent the actual state of PV device use in
the system by LVs and then we compare that to what LVM assumes
based on metadata.
For example:
[0] fedora/~ # lsblk /dev/sdq /dev/sdr /dev/sds /dev/sdt
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
sdq 65:0 0 104M 0 disk
|-vg-lvol0 253:2 0 200M 0 lvm
`-mpath_dev1 253:3 0 104M 0 mpath
sdr 65:16 0 104M 0 disk
`-mpath_dev1 253:3 0 104M 0 mpath
sds 65:32 0 104M 0 disk
|-vg-lvol0 253:2 0 200M 0 lvm
`-mpath_dev2 253:4 0 104M 0 mpath
sdt 65:48 0 104M 0 disk
`-mpath_dev2 253:4 0 104M 0 mpath
In this case the vg-lvol0 is mapped onto sdq and sds becauset this is
what was available and seen during activation. Then later on, sdr and
sdt appeared and mpath devices were created out of sdq+sdr (mpath_dev1)
and sds+sdt (mpath_dev2). Now, LVM assumes (correctly) that mpath_dev1
and mpath_dev2 are the PVs that should be used, not the mpath
components (sdq/sdr, sds/sdt).
[0] fedora/~ # pvs
Found duplicate PV xSUix1GJ2SK82ACFuKzFLAQi8xMfFxnO: using /dev/mapper/mpath_dev1 not /dev/sdq
Using duplicate PV /dev/mapper/mpath_dev1 from subsystem DM, replacing /dev/sdq
Found duplicate PV MvHyMVabtSqr33AbkUrobq1LjP8oiTRm: using /dev/mapper/mpath_dev2 not /dev/sds
Using duplicate PV /dev/mapper/mpath_dev2 from subsystem DM, ignoring /dev/sds
WARNING: Device mismatch detected for vg/lvol0 which is accessing /dev/sdq, /dev/sds instead of /dev/mapper/mpath_dev1, /dev/mapper/mpath_dev2.
PV VG Fmt Attr PSize PFree
/dev/mapper/mpath_dev1 vg lvm2 a-- 100.00m 0
/dev/mapper/mpath_dev2 vg lvm2 a-- 100.00m 0
Add "size" and "size_seqno" to struct device to cache device's size
and also to control its lifetime - the cached value is valid as long
as the global _dev_size_seqno is equal to the device's size_seqno,
otherwise we need to get the size again and cache the new value.
This patch also adds new dev_size_seqno_inc() fn for the appropriate
parts of the code to increment current global value of _dev_size_seqno
and hence to cause all currently cached values for device sizes to
be invalidated.
The device size is now cached because we're planning to reuse this
information for further checks and we want to avoid checking it more
than necessary to save resources.
The list of strings is used quite frequently and we'd like to reuse
this simple structure for report selection support too. Make it part
of libdevmapper for general reuse throughout the code.
This also simplifies the LVM code a bit since we don't need to
include and manage lvm-types.h anymore (the string list was the
only structure defined there).
Changes:
- move device type registration out of "type filter" (filter.c)
to a separate and new dev-type.[ch] for common use throughout the code
- the structure for keeping the major numbers detected for available
device types and available partitioning available is stored in
"dev_types" structure now
- move common partitioning detection code to dev-type.[ch] as well
together with other device-related functions bound to dev_types
(see dev-type.h for the interface)
The dev-type interface contains all common functions used to detect
subsystems/device types, signature/superblock recognition code,
type-specific device properties and other common device properties
(bound to dev_types), including partitioning support.
- add dev_types instance to cmd context as cmd->dev_types for common use
- use cmd->dev_types throughout as a central point for providing
information about device types
