IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
lvm uses a bcache block size of 128K. A bcache block
at the end of the metadata area will overlap the PEs
from which LVs are allocated. How much depends on
alignments. When lvm reads and writes one of these
bcache blocks to update VG metadata, it can also be
reading and writing PEs that belong to an LV.
If these overlapping PEs are being written to by the
LV user (e.g. filesystem) at the same time that lvm
is modifying VG metadata in the overlapping bcache
block, then the user's updates to the PEs can be lost.
This patch is a quick hack to prevent lvm from writing
past the end of the metadata area.
The md filter can operate in two native modes:
- normal: reads only the start of each device
- full: reads both the start and end of each device
md 1.0 devices place the superblock at the end of the device,
so components of this version will only be identified and
excluded when lvm uses the full md filter.
Previously, the full md filter was only used in commands
that could write to the device. Now, the full md filter
is also applied when there is an md 1.0 device present
on the system. This means the 'pvs' command can avoid
displaying md 1.0 components (at the cost of doubling
the i/o to every device on the system.)
(The md filter can operate in a third mode, using udev,
but this is disabled by default because there have been
problems with reliability of the info returned from udev.)
This is the number of concurrent async io requests that
the scan layer will submit to the bcache layer. There
will be an open fd for each of these, so it is best to
keep this well below the default limit for max open files
(1024), otherwise lvm may get EMFILE from open(2) when
there are around 1024 devices to scan on the system.
When lvm2 command is executed in test mode, discard ioctl is skipped.
This may cause even data-loose in case, issuing discard for released
areas was enabled and user 'tested' lvreduce.
udev creates a train wreck of events if we open devices
with RDWR. Until we can fix/disable/scrap udev, work around
this by opening RDONLY and then closing/reopening RDWR when
a write is needed. This invalidates the bcache blocks for
the device before writing so it can trigger unnecessary
rereading.
Remove the io error message from bcache.c since it is not
very useful without the device path.
Make the io error messages from dev_read_bytes/dev_write_bytes
more user friendly.
We have been warning about duplicate devices (and disabling lvmetad)
immediately when the dup was detected (during label_scan). Move the
warnings (and the disabling) to happen later, after label_scan is
finished.
This lets us avoid an unwanted warning message about duplicates
in the special case were md components are eliminated during the
duplicate device resolution.
md devices using an older superblock version have
superblocks at the end of the md device. For commands
that skip reading the end of devices during filtering,
the md component devs will be scanned, and will appear
as duplicate PVs to the original md device. Remove
these md components from the list of unused duplicate
devices, so they are treated as if they had been
ignored during filtering. This avoids the restrictions
that are placed on using PVs with duplicates.
All these functions are now used as utilities,
e.g. for ioctl (not for io), and need to
open/close the device each time they are called.
(Many of the opens can probably be eliminated by
just using the bcache fd for the ioctl.)
Filters are still applied before any device reading or
the label scan, but any filter checks that want to read
the device are skipped and the device is flagged.
After bcache is populated, but before lvm looks for
devices (i.e. before label scan), the filters are
reapplied to the devices that were flagged above.
The filters will then find the data they need in
bcache.
bcache_invalidate() now returns a bool to indicate success. If fails
if the block is currently held, or the block is dirty and writeback
fails.
Added a bunch of unit tests for the invalidate functions.
Fixed some bugs to do with invalidating errored blocks.
The error handling code wasn't working, but it
appears that just removing it is what we need.
The doesn't really need any different behavior
related to bcache blocks on an io error, it just
wants to know if there was an error.
