IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
If the data being requested is present in last_[extra_]devbuf,
return that directly instead of reading it from disk again.
Typical LVM2 access patterns request data within two adjacent 4k blocks
so we eliminate some read() system calls by always reading at least 8k.
Callers that read larger amounts of data now get a pointer to read-only
data directly without copying it through an intermediate buffer. This
data is owned by the device layer so the callers no longer free it.
If it obtains the data, it passes it into the supplied callback function
and returns 1. Otherwise the callback receives failed = 1.
Updated config_file_read_fd to use this and similarly return the data
via a callback fn of its own.
Rename dev_read() to dev_read_buf() - the function that reads data
into a supplied buffer.
Introduce a new dev_read() that allocates the buffer it returns and
switch the important users over to this. No caller may change the
returned data. (For now, callers are responsible for freeing it after
use, but later the device layer will take full ownership.)
dev_read_buf() should only be used for tiny buffers or unimportant code
(such as the old disk formats).
The creation of wrapped around metadata - where the start of metadata is
written up to the end of the buffer and the remainder follows back at
the start of the buffer - is now restricted to cases where writing the
metadata in one piece wouldn't fit. This shouldn't happen in 'normal'
usage so let's begin treating the code for this as a special case that
can be ignored when optimising 'normal' cases.
Mark the first metadata area on each text format PV as MDA_PRIMARY.
Pass this information down to the device layer so that when
there are two metadata areas on a block device, we can easily
distinguish two independent streams of I/O.
Introduce enum dev_io_reason to categorise block device I/O
in debug messages so it's obvious what it is for.
DEV_IO_SIGNATURES /* Scanning device signatures */
DEV_IO_LABEL /* LVM PV disk label */
DEV_IO_MDA_HEADER /* Text format metadata area header */
DEV_IO_MDA_CONTENT /* Text format metadata area content */
DEV_IO_FMT1 /* Original LVM1 metadata format */
DEV_IO_POOL /* Pool metadata format */
DEV_IO_LV /* Content written to an LV */
DEV_IO_LOG /* Logging messages */
- Use 'lvmcache' consistently instead of 'metadata cache'
- Always use 5 characters for source line number
- Remember to convert uuids into printable form
- Use <no name> rather than (null) when VG has no name.
Replaced the confusing device error message "not found (or ignored by
filtering)" by either "not found" or "excluded by a filter".
(Later we should be able to say which filter.)
Left the the liblvm code paths alone.
Older udev versions (udev < v165), don't have the official
udev_device_get_is_initialized function available to query for
device initialization state in udev database. Also, devices don't
have USEC_INITIALIZED udev db variable set - this is bound to the
udev_device_get_is_initialized fn functionality.
In this case, check for "DEVLINKS" variable instead - all block devices
have at least one symlink set for the node (the "/dev/block/<major:minor>".
This symlink is set by default basic udev rules provided by udev directly.
We'll use this as an alternative for the check that initial udev
processing for a device has already finished.
Treat loop device created with 'losetup -P' as regular
partitioned device - so if it has partition table,
prevent its usage in commands like 'pvcreate'.
Before 'pvcreate /dev/loop0' could have erased and formated as PV,
after this patch, device is filtered out and cannot be used.
When not obtaining device from udev, we are doing deep devdir scan,
and at the same time we try to insert everything what /sys/dev/block
knows about. However in case lvm2 is configured to use nonstardard
devdir this way it will see (and scan) devices from a real system.
lvm2 test suite is using its own test devdir with its
own device nodes. To avoid touching real /dev devices, validate
the device node exist in give dir and do not insert such device
into a cache.
With obtain list from udev this patch has no effect
(the normal user path).
We have _insert_dirs() for udev and non-udev compilation.
Compiling without udev missed to call dev_cache_index_devs().
Move the call after _insert_dirs() call so both compilation
gets it.
/sys/dev/block is available since kernel version 2.2.26 (~ 2008):
https://www.kernel.org/doc/Documentation/ABI/testing/sysfs-dev
The VGID/LVID indexing code relies on this feature so skip indexing
if it's not available to avoid error messages about inability to open
/sys/dev/block directory.
We're not going to provide fallback code to read the /sys/block/
instead in this case as that's not that efficient - it needs extra
reads for getting major:minor and reading partitions would also
pose further reads and that's not worth it.
If obtain_device_list_from_udev=0, LVM can make use of persistent .cache
file. This cache file contains only devices which underwent filters in
previous LVM command run. But we need to iterate over all block devices
to create the VGID/LVID index completely for the device mismatch check
to be complete as well.
This patch iterates over block devices found in sysfs to generate the
VGID/LVID index in dev cache if obtain_device_list_from_udev=0
(if obtain_device_list_from_udev=1, we always read complete list of
block devices from udev and we ignore .cache file so we don't need
to look in sysfs for the complete list).
For the case when we print device name associated with struct device
that was not found in /dev, but in sysfs, for example when printing
devices where LV device mismatch is found.
