IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Fix setvbuf code by closing and reopening stream before changing buffer.
But we need to review what this code is doing embedded inside a library
function rather than the simpler original form being run independently
at the top of main() by tools that need it.
Accept -q as the short form of --quiet.
Suppress non-essential standard output if -q is given twice.
Treat log/silent in lvm.conf as equivalent to -qq.
Review all log_print messages and change some to
log_print_unless_silent.
When silent, the following commands still produce output:
dumpconfig, lvdisplay, lvmdiskscan, lvs, pvck, pvdisplay,
pvs, version, vgcfgrestore -l, vgdisplay, vgs.
[Needs checking.]
Non-essential messages are shifted from log level 4 to log level 5
for syslog and lvm2_log_fn purposes.
This patch adds support for RAID10. It is not the default at this
stage. The user needs to specify '--type raid10' if they would like
RAID10 instead of stacked mirror over stripe.
Remove the limit for major and minor number arguments used while specifying
persistent numbers via -My --major <major> --minor <minor> option which
was set to 255 before. Follow the kernel limit instead which is 12 bits
for major and 20 bits for minor number (kernel >= 2.6 and LVM formats
that does not have FMT_RESTRICTED_LVIDS - so still keep the old limit
of 255 for lvm1 format).
Allowing people to add devices to a VG that has PVs missing helps
people avoid the inability to repair RAID LVs in certain cases.
For example, if a user creates a RAID 4/5/6 LV using all of the
available devices in a VG, there will be no spare devices to
repair the LV with if a device should fail. Further, because the
VG is missing a device, new devices cannot be added to allow the
repair. If 'vgreduce --removemissing' were attempted, the
"MISSING" PV could not be removed without also destroying the RAID
LV.
Allowing vgextend to operate solves the circular dependency.
When the PV is added by a vgextend operation, the sequence number is
incremented and the 'MISSING' flag is put on the PVs which are missing.
A regression introduced in 2.02.89 (11e520256b)
caused the lvm dumpconfig <node> to print out
the node as well as its subsequent siblings.
The information about "only_one" mode got lost.
Before this patch (just an example node):
# lvm dumpconfig global/use_lvmetad
use_lvmetad=1
thin_check_executable="/usr/sbin/thin_check"
thin_check_options="-q"
(...all nodes to the end of the section)
With this patch applied:
# lvm dumpconfig global/use_lvmetad
use_lvmetad=1
If a daemon (like lvmetad that is using common daemon-server code)
received a kill signal that was supposed to shut the daemon down,
a spurious message was issued: "Failed to handle a client connection".
This happened if the kill signal came just in the middle of waiting
for a client request in "select" - the request that was supposed to
be handled was blank at that moment of course.
Update lvchange to allow change of 'zero' flag for thinpool.
Add support for changing discard handling.
N.B. from/to ignore could be only changed for inactive pool.
Add arg support for discard.
Add discard ignore, nopassdown, passdown (=default) support.
Flags could be set per pool.
lvcreate [--discard {ignore|no_passdown|passdown}] vg/thinlv
When --sysinit -a ay is used with vg/lvchange and lvmetad is up and running,
we should skip manual activation as that would be a useless step - all volumes
are autoactivated once all the PVs for a VG are present.
If lvmetad is not active at the time of the vgchange --sysinit -a ay
call, the activation proceeds in standard 'manual' way.
This way, we can still have vg/lvchange --sysinit -a ay called
unconditionally in system initialization scripts no matter if lvmetad
is used or not.
Reducing a RAID 4/5/6 LV or extending it with a different number of
stripes is still not implemented. This patch covers the "simple" case
where the LV is extended with the same number of stripes as the orginal.
In process_each_pv() if we haven't yet scanned and the PV appears
to be an orphan, we must scan the other PVs looking for mdas that
reference it to find out what VG it is in.
1. If the PV has no mdas, we must scan.
2. If the PV has an mda that is not ignored we do not need to scan.
3. If the PV has an mda that is ignored, we do need to scan.
This patch fixes case 3.
> pvs -o +mda_count,vg_mda_count /dev/loop[0123]
PV VG Fmt Attr PSize PFree #PMda #VMda
/dev/loop0 vg3 lvm2 a- 96.00m 96.00m 0 1
/dev/loop1 vg3 lvm2 a- 96.00m 96.00m 1 1
/dev/loop2 vg2 lvm2 a- 96.00m 96.00m 1 2
/dev/loop3 vg2 lvm2 a- 28.00m 28.00m 1 2
Before:
> pvs /dev/loop2 /dev/loop3 /dev/loop0 /dev/loop1 --unbuffered
PV VG Fmt Attr PSize PFree
/dev/loop2 lvm2 a-- 100.00m 100.00m
/dev/loop3 vg2 lvm2 a-- 28.00m 28.00m
/dev/loop0 lvm2 a-- 100.00m 100.00m
/dev/loop1 vg3 lvm2 a-- 96.00m 96.00m
After:
> pvs /dev/loop2 /dev/loop3 /dev/loop0 /dev/loop1 --unbuffered
PV VG Fmt Attr PSize PFree
/dev/loop2 vg2 lvm2 a-- 96.00m 96.00m
/dev/loop3 vg2 lvm2 a-- 28.00m 28.00m
/dev/loop0 vg3 lvm2 a-- 96.00m 96.00m
/dev/loop1 vg3 lvm2 a-- 96.00m 96.00m
If _alloc_parallel_area for raid devices chooses an area already used
up, it doesn't notice that it has no space left in it and leaves
later code trying to place a zero-length area into the LV.
https://bugzilla.redhat.com/832596
The clmvd init script called "vgchange -aly" before to activate
all VGs in cluster environment. This activated all VGs, no matter
if it was clustered or not.
Auto activation for clustered VGs is not supported yet so the behaviour
of -aay is still the same as before for clustered VGs. However, for
non-clustered VGs, we need to check with the activation/auto_activation_volume_list
whether the VG/LV should be activated on boot or not.
One can use "lvcreate --aay" to have the newly created volume
activated or not activated based on the activation/auto_activation_volume_list
this way.
Note: -Z/--zero is not compatible with -aay, zeroing is not used in this case!
When using lvcreate -aay, a default warning message is also issued that zeroing
is not done.
Define auto_activation_handler that activates VGs/LVs automatically
based on the activation/auto_activation_volume_list (activating all
volumes by default if the list is not defined).
The autoactivation is done within the pvscan call in 69-dm-lvmetad.rules
that watches for udev events (device appearance/removal).
For now, this works for non-clustered and complete VGs only.
Normally, the 'vgchange -ay' activates all volume groups (that pass
the activation/volume_list filter if set).
This call can appear in two scenarios:
- system boot (so activation within a script in general)
- manual call on command line (so activaton on user's direct request)
For the former one, we would like to select which VGs should be actually
activated. One can define the list of VGs directly to do that. But that
would require the same list to be provided in all the scripts.
The 'vgchange -aay' will check for the activation/auto_activation_volume_list
in adition and it will activate only those VGs/LVs that pass this
filter (assuming all to be activated if the list is not defined - the
same logic we already have for activation/volume_list).
Init/boot scripts should use this form of activation primarily
(which, anyway, becomes only a fallback now with autoactivation done
on PV appearance in tandem with lvmetad in place).
Define an 'activation_handler' that gets called automatically on
PV appearance/disappearance while processing the lvmetad_pv_found
and lvmetad_pv_gone functions that are supposed to update the
lvmetad state based on PV availability state. For now, the actual
support is for PV appearance only, leaving room for PV disappearance
support as well (which is a more complex problem to solve as this
needs to count with possible device stack).
Add a new activation change mode - CHANGE_AAY exposed as
'--activate ay/-aay' argument ('activate automatically').
Factor out the vgchange activation functionality for use in other
tools (like pvscan...).
We're refererring to 'activation' all over the code and we're talking
about 'LVs being activated' all the time so let's use 'activation/activate'
everywhere for clarity and consistency (still providing the old
'available' keyword as a synonym for backward compatibility with
existing environments).
Update release_lv_segment_area not to discard any PV extents,
as it also gets used when moving extents between LVs.
Instead, call a new function release_and_discard_lv_segment_area() in
the two places where data should be discarded - lv_reduce() and
remove_mirrors_from_segments().
There's no need to have the device open RW while obtaining the readahead value.
The RW open used before caused the CHANGE udev event to be generated if the
WATCH udev rule was set for the underlying device (and that is normally the
case both for non-dm and dm devices by default).
This did not cause any problems before since we were not interested in
*underlying* devices. However, with upcoming changes (autoactivation), we're
watching for events on underlying devices marked as PVs and such a spurious
event could cause the autoactivation code to be triggered. So when trying
to deactivate the volume, we could end up with immediate activation just after
that because of the CHANGE event originated in the WATCH udev rule since the
underlying device was open RW during the deactivation process.
Though maybe a better solution would be to completely filter such spurious
events out of the autoactivation process somehow, it's still useful if there
are as least spurious events generated as possible in the system itself.
