IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
We've used udev fallback code till now to check whether udev
created/removed the entries in /dev correctly and if not,
a repair was done (giving a warning messagea about that).
This patch adds a possibility to enable this additional check
and subsequent fallback only when required (debugging purposes
mostly) and trust udev completely.
So let's disable the fallback code by default and add a new
configuration option "activation/udev_fallback".
(The original code for creating the nodes will still be used
in case the device directory that is set in lvm.conf differs
from the one that udev uses and also when activation/udev_rules
is set to 0 - otherwise we would end up with no nodes/symlinks
at all)
Also, add a new 'obtain_device_list_from_udev' setting to lvm.conf with which
we can turn this feature on or off if needed.
If set, the cache of block device nodes with all associated symlinks
will be constructed out of the existing udev database content.
This avoids using and opening any inapplicable non-block devices or
subdirectories found in the device directory. This setting is applied
to udev-managed device directory only, other directories will be scanned
fully. LVM2 needs to be compiled with udev support for this setting to
take effect. N.B. Any device node or symlink not managed by udev in
udev directory will be ignored with this setting on.
Makes the code more readable and has a smaller number of memory
accesses thus it's small optimisation as well.
For _get_token() optimize number parsing. Check for '.' char only
if it's not a digit. Move pointer incrementation into one place.
For _eat_space() check only p->te for '\0' in skipping of comment line.
Avoid check for '\0' when we know it is space. Also master while loop
doesn't need checking p->tb for '\0'. We just need to check p->tb
isn't already at the end of buffer. This could give 'extra' loop cycle
if we are already there - but safes memory access in every other case.
There is a lot to test.
Two new config settings added that are intended to make the code behave
closely to the way it did before - worth a try if you find problems.
strncpy (which check each byte for \0) is not need as we always copy
the length size - so using memcpy is a bit cheaper.
Add missing log_error message for failed allocation.
Add checks for clonning allocation a fail-out when something is
not allocated correctly.
Also move var declaration to the begining of the function
and fix log_error messages.
To have better control were the config tree could be modified use more
const pointers and very carefully downcast them back to non-const
(for config tree merge).
Add test for NULL from dm_poll_create.
Reorder dm_pool_destroy() before file close and add label out:.
Avoid leaking file descriptor if the allocation fails.
to lvm.conf in the activation section: 'snapshot_autoextend_threshold' and
'snapshot_autoextend_percent', that define how to handle automatic snapshot
extension. The former defines when the snapshot should be extended: when its
space usage exceeds this many percent. The latter defines how much extra space
should be allocated for the snapshot, in percent of its current size.
Add "devices/default_data_alignment" to lvm.conf to control the internal
default that LVM2 uses: 0==64k, 1==1MB, 2==2MB, etc.
If --dataalignment (or lvm.conf's "devices/data_alignment") is specified
then it is always used to align the start of the data area. This means
the md_chunk_alignment and data_alignment_detection are disabled if set.
(Same now applies to pvcreate --dataalignmentoffset, the specified value
will be used instead of the result from data_alignment_offset_detection)
set_pe_align() still looks to use the determined default alignment
(based on lvm.conf's default_data_alignment) if the default is a
multiple of the MD or topology detected values.
The new standard in the storage industry is to default alignment of data
areas to 1MB. fdisk, parted, and mdadm have all been updated to this
default.
Update LVM to align the PV's data area start (pe_start) to 1MB. This
provides a more useful default than the previous default of 64K (which
generally ended up being a 192K pe_start once the first metadata area
was created).
Before this patch:
# pvs -o name,vg_mda_size,pe_start
PV VMdaSize 1st PE
/dev/sdd 188.00k 192.00k
After this patch:
# pvs -o name,vg_mda_size,pe_start
PV VMdaSize 1st PE
/dev/sdd 1020.00k 1.00m
The heuristic for setting the default alignment for LVM data areas is:
- If the default value (1MB) is a multiple of the detected alignment
then just use the default.
- Otherwise, use the detected value.
In practice this means we'll almost always use 1MB -- that is unless:
- the alignment was explicitly specified with --dataalignment
- or MD's full stripe width, or the {minimum,optimal}_io_size exceeds
1MB
- or the specified/detected value is not a power-of-2
Introduce --norestorefile to allow user to override the new requirement.
This can also be overridden with "devices/require_restorefile_with_uuid"
in lvm.conf -- however the default is 1.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Allow metadataignore flag to be passed in to pvcreate.
Ideally, more refactoring of the mda allocation / initialization
is warranted, but for now, we just add another parameter to 'add_mda'
to take an existing mda ignored flag. We need to do this or pv_write
loses the state of the mda 'ignored' flag before copying and writing
to disk.
Add a field to struct volume_group to later implement metadata
balancing:
- mda_copies: target # of non-ignored mdas in the VG; default 0 (do
not control pv 'ignore mdas' bit.
This patch just adds the parameter to the structures with the default
values but does not modify any commands. Should be no functional change.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
This patch adds a new implementation of locking function instead
of mlockall() that may lock way too much memory (>100MB).
New function instead uses mlock() system call and selectively locks
memory areas from /proc/self/maps trying to avoid locking areas
unused during lock-ed state.
Patch also adds struct cmd_context to all memlock() calls to have
access to configuration.
For backward compatibility functionality of mlockall()
is preserved with "activation/use_mlockall" flag.
As a simple check, locking and unlocking counts the amount of memory
and compares whether values are matching.
the background polldaemon is allowed to start. It can be used
standalone or in conjunction with --refresh or --available y.
Control over when the background polldaemon starts will be particularly
important for snapshot-merge of a root filesystem.
Dracut will be updated to activate all LVs with: --poll n
The lvm2-monitor initscript will start polling with: --poll y
NOTE: Because we currently have no way of knowing if a background
polldaemon is active for a given LV the following limitations exist and
have been deemed acceptable:
1) it is not possible to stop an active polldaemon; so the lvm2-monitor
initscript doesn't stop running polldaemon(s)
2) redundant polldaemon instances will be started for all specified LVs
if vgchange or lvchange are repeatedly used with '--poll y'
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add configure --enable-units-compat to set si_unit_consistency off by default.
Use standard output units for 'PE Size' and 'Stripe size' in pv/lvdisplay.
