IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Do this at two levels, although one would be enough to
fix the problem seen recently:
- Ignore any reported sector size other than 512 of 4096.
If either sector size (physical or logical) is reported
as 512, then use 512. If neither are reported as 512,
and one or the other is reported as 4096, then use 4096.
If neither is reported as either 512 or 4096, then use 512.
- When rounding up a limited write in bcache to be a multiple
of the sector size, check that the resulting write size is
not larger than the bcache block itself. (This shouldn't
happen if the sector size is 512 or 4096.)
An active md device with an end superblock causes lvm to
enable full md component detection. This was being done
within the filter loop instead of before, so the full
filtering of some devs could be missed.
Also incorporate the recently added config setting that
controls the md component detection.
If udev info is missing for a device, (which would indicate
if it's an MD component), then do an end-of-device read to
check if a PV is an MD component. (This is skipped when
using hints since we already know devs in hints are good.)
A new config setting md_component_checks can be used to
disable the additional end-of-device MD checks, or to
always enable end-of-device MD checks.
When both hints and udev info are disabled/unavailable,
the end of PVs will now be scanned by default. If md
devices with end-of-device superblocks are not being
used, the extra I/O overhead can be avoided by setting
md_component_checks="start".
udev_dev_is_md_component and udev_dev_is_mpath_component
are not used for obtaining the device list, but they still
use libudev for device info. When there are problems with
udev, these functions can get stuck. So, use the existing
obtain_device_list_from_udev config setting to also control
whether these "is component" functions are used, which gives
us a way to avoid using libudev entirely when it's causing
problems.
Save the list of PVs in /run/lvm/hints. These hints
are used to reduce scanning in a number of commands
to only the PVs on the system, or only the PVs in a
requested VG (rather than all devices on the system.)
Ensure configure.h is always 1st. included header.
Maybe we could eventually introduce gcc -include option, but for now
this better uses dependency tracking.
Also move _REENTRANT and _GNU_SOURCE into configure.h so it
doesn't need to be present in various source files.
This ensures consistent compilation of headers like stdio.h since
it may produce different declaration.
commit de28637
scan: use full md filter when md 1.0 devices are present
missed the fact that md superblock version 0.90 also puts
metadata at the end of the device, so the full md filter
needs to be used when either 0.90 or 1.0 is present.
fix lseek error check
fix read/write error checks
handle zero return from read and write
don't return an error for short io
fix partial read/write loop
io_setup() for aio may fail if a system has reached the
aio request limit. In this case, fall back to using
sync io. Also, lvm use of aio can be disabled entirely
with config setting global/use_aio=0.
The system limit for aio requests can be seen from
/proc/sys/fs/aio-max-nr
The current usage of aio requests can be seen from
/proc/sys/fs/aio-nr
The system limit for aio requests can be increased by
setting fs.aio-max-nr using sysctl.
Also add last-byte limit to the sync io code.
lvm uses a bcache block size of 128K. A bcache block
at the end of the metadata area will overlap the PEs
from which LVs are allocated. How much depends on
alignments. When lvm reads and writes one of these
bcache blocks to update VG metadata, it can also be
reading and writing PEs that belong to an LV.
If these overlapping PEs are being written to by the
LV user (e.g. filesystem) at the same time that lvm
is modifying VG metadata in the overlapping bcache
block, then the user's updates to the PEs can be lost.
This patch is a quick hack to prevent lvm from writing
past the end of the metadata area.
This is the number of concurrent async io requests that
the scan layer will submit to the bcache layer. There
will be an open fd for each of these, so it is best to
keep this well below the default limit for max open files
(1024), otherwise lvm may get EMFILE from open(2) when
there are around 1024 devices to scan on the system.
When lvm2 command is executed in test mode, discard ioctl is skipped.
This may cause even data-loose in case, issuing discard for released
areas was enabled and user 'tested' lvreduce.
udev creates a train wreck of events if we open devices
with RDWR. Until we can fix/disable/scrap udev, work around
this by opening RDONLY and then closing/reopening RDWR when
a write is needed. This invalidates the bcache blocks for
the device before writing so it can trigger unnecessary
rereading.
The md filter can operate in two native modes:
- normal: reads only the start of each device
- full: reads both the start and end of each device
md 1.0 devices place the superblock at the end of the device,
so components of this version will only be identified and
excluded when lvm uses the full md filter.
Previously, the full md filter was only used in commands
that could write to the device. Now, the full md filter
is also applied when there is an md 1.0 device present
on the system. This means the 'pvs' command can avoid
displaying md 1.0 components (at the cost of doubling
the i/o to every device on the system.)
(The md filter can operate in a third mode, using udev,
but this is disabled by default because there have been
problems with reliability of the info returned from udev.)
