IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
When valgrind usage is desired by user (--enable-valgrind-pool)
skip playing/closing/reopenning with descriptors - it makes
valgridng useless.
Make sleep delay for clvmd start longer.
A while back, the behavior of LVM changed from allowing metadata changes
when PVs were missing to not allowing changes. Until recently, this
change was tolerated by HA-LVM by forcing a 'vgreduce --removemissing'
before trying (again) to add tags to an LV and then activate it. LVM
mirroring requires that failed devices are removed anyway, so this was
largely harmless. However, RAID LVs do not require devices to be removed
from the array in order to be activated. In fact, in an HA-LVM
environment this would be very undesirable. Device failures in such an
environment can often be transient and it would be much better to restore
the device to the array than synchronize an entirely new device.
There are two methods that can be used to setup an HA-LVM environment:
"clvm" or "tagging". For RAID LVs, "clvm" is out of the question because
RAID LVs are not supported in clustered VGs - not even in an exclusively
activated manner. That leaves "tagging". HA-LVM uses tagging - coupled
with 'volume_list' - to ensure that only one machine can have an LV active
at a time. If updates are not allowed when a PV is missing, it is
impossible to add or remove tags to allow for activation. This removes
one of the most basic functionalities of HA-LVM - site redundancy. If
mirroring or RAID is used to replicate the storage in two data centers
and one of them goes down, a server and a storage device are lost. When
the service fails-over to the alternate site, the VG will be "partial".
Unable to add a tag to the VG/LV, the RAID device will be unable to
activate.
The solution is to allow vgchange and lvchange to alter the LVM metadata
for a limited set of options - --[add|del]tag included. The set of
allowable options are ones that do not cause changes to the DM kernel
target (like --resync would) or could alter the structure of the LV
(like allocation or conversion).
Compared to names, UUIDs can't be renamed once they are created
for a device. The 'mangle' command will just issue an error message
about a need for manual intervention in this case - reactivating the
device (remove + create) does the job as the defualt mangling mode
used is "auto" and that will assign a correct mangled form the UUID.
For now this convertions is not supported, thus disabled.
The only supported conversion for now is to create mirrored thin pools
from mirrored devices.
Update code for lvconvert.
Change the lvconvert user interface a bit - now we require 2 specifiers
--thinpool takes LV name for data device (and makes the name)
--poolmetadata takes LV name for metadata device.
Fix type in thin help text -z -> -Z.
Supported is also new flag --discards for thinpools.
When reformatting the 'lvchange_resync' code in commit
05131f5853, a '!' should have been removed
from the condition that checks for the LV_NOTSYNCED flag on a corelog
mirror LV. The presence of this '!' caused the LV_NOTSYNCED flag to be
cleared when it wasn't present and left when it was present.
It is not allowed to add images to a 'mirror' or 'raid1' LV if the
LV_NOTSYNCED flag is set. We add some up-convert tests to ensure this
behavior is being enforced and that the LV_NOTSYNCED flag is being
properly cleared by 'lvchange --resync'.
(Not updating WHATS_NEW because this is intrarelease.)
Don't try to issue discards to a missing PV to avoid segfault.
Prevent lvremove from removing LVs that have any part missing.
https://bugzilla.redhat.com/857554
Using 'activation/auto_activation_volume_list = [ "vg/lvol1" ]'.
Before this patch:
3 logical volume(s) in volume group "vg" now active
LV VG Attr LSize Pool Origin Data% Move Log Copy% Convert
lvol0 vg -wi----- 4.00m
lvol1 vg -wi-a--- 4.00m
lvol2 vg -wi-a--- 4.00m
lvol3 vg -wi-a--- 4.00m
(vg/lvol1 activated as it passes the list and all subsequent volumes too - wrong!)
With this patch:
1 logical volume(s) in volume group "vg" now active
LV VG Attr LSize Pool Origin Data% Move Log Copy% Convert
lvol0 vg -wi----- 4.00m
lvol1 vg -wi-a--- 4.00m
lvol2 vg -wi----- 4.00m
lvol3 vg -wi----- 4.00m
(only vg/lvol1 activated as it passes the list and no other - correct!)
Issuing a 'lvchange --resync <VG>/<RAID_LV>' had no effect. This is
because the code to handle RAID LVs was not present. This patch adds
the code that will clear the metadata areas of RAID LVs - causing them
to resync upon activation.
When an LV is to be resynced, the metadata areas are cleared and the
LV is reactivated. This is true for mirroring and will also be true
for RAID LVs. We restructure the code in lvchange_resync() so that we
keep all the common steps necessary (validation of ability to resync,
deactivation, activation of meta/log devices, clearing of those devices,
etc) and place the code that will be divergent in separate functions:
detach_metadata_devices()
attach_metadata_devices()
The common steps will be processed on lists of metadata devices. Before
RAID capability is added, this will simply be the mirror log device (if
found).
This patch lays the ground-work for adding resync of RAID LVs.
By changing the conditional for resyncing mirrors with core-logs a
bit, we can short-circuit the rest of the function for that case
and reduce the amount of indenting in the rest of the function.
This cleanup will simplify future patches aimed at properly handling
the resync of RAID LVs.
When printing a message for the user and the lv_segment pointer is available,
use segtype->ops->name() instead of segtype->name. This gives a better
user-readable name for the segment. This is especially true for the
'striped' segment type, which prints "linear" if there is an area_count of
one.
We should check whether the fd is opened before trying to reopen it.
For example, the stdin is closed in test/lib/harness.c causing the
test suite to fail.
Accept -q as the short form of --quiet.
Suppress non-essential standard output if -q is given twice.
Treat log/silent in lvm.conf as equivalent to -qq.
Review all log_print messages and change some to
log_print_unless_silent.
When silent, the following commands still produce output:
dumpconfig, lvdisplay, lvmdiskscan, lvs, pvck, pvdisplay,
pvs, version, vgcfgrestore -l, vgdisplay, vgs.
[Needs checking.]
Non-essential messages are shifted from log level 4 to log level 5
for syslog and lvm2_log_fn purposes.
This patch adds support for RAID10. It is not the default at this
stage. The user needs to specify '--type raid10' if they would like
RAID10 instead of stacked mirror over stripe.
Adding couple INTERNAL_ERROR reports for unwanted parameters:
Ensure the 'top' metadata node cannot be NULL for lvmetad.
Make obvious vginfo2 cannot be NULL.
Report internal error if handler and vg is undefined.
Check for handle in poll_vg().
Ensure seg is not NULL in dev_manager_transient().
Report missing read_ahead for _lv_read_ahead_single().
Check for report handler in dm_report_object().
Check missing VG in _vgreduce_single().
