IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Commit 3501f17fd0 enables a limited set
of metadata updates for partial LV/VGs when issuing lvchange or vgchange.
These tests verify those changes operate as intended.
Separate original raid test and new raid10 test,
so the old could be tested on platforms without raid10 support.
Replace test-unfriendly `ls /dev/mapper` with dmsetup ls
Revert changes to origin lvcreate-large test and use separate
test scripts for raid - so they can be properly skipped when
kernel doesn't support raid targets.
MD's bitmaps can handle 2^21 regions at most. The RAID code has always
used a region_size of 1024 sectors. That means the size of a RAID LV was
limited to 1TiB. (The user can adjust the region_size when creating a
RAID LV, which can affect the maximum size.) Thus, creating, extending or
converting to a RAID LV greater than 1TiB would result in a failure to
load the new device-mapper table.
Again, the size of the RAID LV is not limited by how much space is allocated
for the metadata area, but by the limitations of the MD bitmap. Therefore,
we must adjust the 'region_size' to ensure that the number of regions does
not exceed the limit. I've added code to do this when extending a RAID LV
(which covers 'create' and 'extend' operations) and when up-converting -
specifically from linear to RAID1.
When reformatting the 'lvchange_resync' code in commit
05131f5853, a '!' should have been removed
from the condition that checks for the LV_NOTSYNCED flag on a corelog
mirror LV. The presence of this '!' caused the LV_NOTSYNCED flag to be
cleared when it wasn't present and left when it was present.
It is not allowed to add images to a 'mirror' or 'raid1' LV if the
LV_NOTSYNCED flag is set. We add some up-convert tests to ensure this
behavior is being enforced and that the LV_NOTSYNCED flag is being
properly cleared by 'lvchange --resync'.
(Not updating WHATS_NEW because this is intrarelease.)
This patch adds support for RAID10. It is not the default at this
stage. The user needs to specify '--type raid10' if they would like
RAID10 instead of stacked mirror over stripe.
Commit 8767435ef8 allowed RAID 4/5/6
LV to be extended properly, but introduced a regression in device
replacement - a critical component of fault tolerance.
When only 1 or 2 drives are being replaced, the 'area_count' needed
can be equal to the parity_count. The 'area_multiple' for RAID 4/5/6
was computed as 'area_count - parity_devs', which could result in
'area_multiple' being 0. This would ultimately lead to a division by
zero error. Therefore, in calc_area_multiple, it is important to take
into account the number of areas that are being requested - just as
we already do in _alloc_init.
Reducing a RAID 4/5/6 LV or extending it with a different number of
stripes is still not implemented. This patch covers the "simple" case
where the LV is extended with the same number of stripes as the orginal.
When mirrors are up-converted, a transient mirror layer is put in so that
only the new devices are sync'ed. That transient layer must carry the tags
of the original mirror LV, otherwise it will fail to activate when activation
is regulated by lvm.conf:activation/volume_list. The conversion would then
fail.
The fix is to do exactly the same thing that is being done for linear ->
mirror converting (lib/metadata/mirror.c:_init_mirror_log()). We copy the
tags temporarily for the new LV and remove them after the activation.
Snapshots of RAID logical volumes are allowed (including "raid1"). However,
snapshots of "mirror" logical volumes has been disallowed due to unsolvable
issues inherent to the design. The fact that mirroring (dm-raid1.c) must
stop all I/O as the result of a failure and wait for userspace intervention
can lead to a circular dependency if userspace is simultaneously waiting for
snapshots (on mirrors) to make an I/O update before proceeding.
Various snapshot on mirror tests have been removed as a result.
Add make help target.
Add LVM_TEST_PARALLEL to support parallel runs of tests
Work around the problem the dmsetup table/info may return error
by using dmtable and dminfo function that will use 'should'.
(Error happens when some concurently running process removes table
entry while dmsetup command resolves table entries inside the loop.)
