IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Add new targets:
make check_lvmpolld
make check_cluster_lvmpolld
make check_lvmetad_lvmpolld
make check_all_lvmpolld
So check_lvmetad runs only base lvmetad test - to much
logic of remaining targets.
Previous behavior is available via check_all_lvmpolld.
Check for dm-raid target version with non-standard raid4 mapping expecting the dedicated
parity device in the last rather than the first slot and prohibit to create, activate or
convert to such LVs from striped/raid0* or vice-versa in order to avoid data corruption.
Add related tests to lvconvert-raid-takeover.sh
Resolves: rhbz1388962
On conversions between striped/raid0* and raid4, the kernel expects
the dedicated raid4 parity SubLVs in the first segment area rather than
in the last it's been allocated to, thus the data mapping ain't proper.
Enhance lvconvert (lib/metadata/raid_manip.c) to shift the dedicated
parity SubLVs on conversions from striped/raid0* to raid4 and vice-versa.
In case of raid0_meta -> raid4 where the MD raid0 personality already has
stored RAID array device positions in the superblocks, the MetaLVs have to
be cleared so that the kernel doesn't fail validating the array positions
after lvm has shifted them up by one.
Add more tests to lvconvert-raid-takeover.sh including one to check for
mapping flaws by converting a created raid4 with filesystem -> striped
and fsck it.
Whilst on it:
- add missing direct striped -> raid4 conversion to the takeover array
to avoid an intermim conversion from striped -> raid0*
- clean up the takeover array
- allow lvconvert to actually call lv_raid_convert() on all takeover requests
in order to check parameters and display messages provided by takeover
functions rather than just "...not supported" from within lvconvert
- fix a typo
Resolves: rhbz1386148
This test never passes on loop back, so we will skip unless the
pv devices are real devices which contain `/dev/sd`.
We always fail because we need lvm to run slow to get a timer to
pop, and loopback are too fast.
If you run multiple runs of unittest.main, unless you don't pass exit=true
the test case always ends with a 0 exit code. Add ability to store the
result of each invocation of the test and exit with a non-zero exit code
if anyone of them fail.
Fix missing wait so we have paired waiting.
Also 'wait' for precise PID to get 'exit' code.
Test for 'error' replacing only with newer snapshot targets.
The old one will wait for resume.
Note: 'wait -n' is not always available so can't be used..
Pre 1.9 dm-raid targets status output was racy, which caused
the device status chars to be unreliable _during_ synchronization.
This shows paritcularly with tiny test devices used.
Enhance lvchange-rebuild-raid.sh to not check status
chars _during_ synchronization. Just check afterwards.
Though I'm not quite sure why we push this limit on user,
current --repair logic requires user to wait outside of command.
TODO: I'm not quite sure this repair logic is 'the most wanted'.
The dm-raid target now rejects device rebuild requests during ongoing
resynchronization thus causing 'lvconvert --repair ...' to fail with
a kernel error message. This regresses with respect to failing automatic
repair via the dmeventd RAID plugin in case raid_fault_policy="allocate"
is configured in lvm.conf as well.
Previously allowing such repair request required cancelling the
resynchronization of any still accessible DataLVs, hence reasoning
potential data loss.
Patch allows the resynchronization of still accessible DataLVs to
finish up by rejecting any 'lvconvert --repair ...'.
It enhances the dmeventd RAID plugin to be able to automatically repair
by postponing the repair after synchronization ended.
More tests are added to lvconvert-rebuild-raid.sh to cover single
and multiple DataLV failure cases for the different RAID levels.
- resolves: rhbz1371717
Commit 199697accf rerouted funtion
for priting cache volume origin to lvm2app app function - which
however had a bug. So restore the original functionality
and print correct LV as cache origin LV.
Because of the different code paths we need to test job handling with
all operations. Test now runs virtually everything with timeout == 0
and timeout == 15 so that we test both use cases.
Note: If a client passes -1 for the timeout value they need to make
sure that their connection time out is also infinite. Otherwise, if the client
times out the service side hangs any new dbus calls until the job
that is in progress completes. Not sure why this behavior is occuring
at this time, but it appears a limitation/bug of the dbus-python library.
The methods were returning an instance of the object instead of the
object path which was causing an exception when the result was returned
with the job object as we are explicity trying to return an object path.
Unit test added which re-creates the issue and verifies the fix.
Add simple helper/wrapper check function to check result
of dmsetup call i.e.:
check grep_dmsetup table vg-lv "grep_expected"
check grep_dmsetup status vg-lv -v "grep_unexpected"
