IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
We can consider the drive firmware a server to handle the locking
request from nodes, this essentially is a client-server model.
DLM uses the kernel as a central place to manage locks, so it also
complies with client-server model for locking operations. This is
why IDM and DLM are similar with each other for their wrappers.
This patch largely works by generalizing the DLM code paths and then
providing degeneralized functions as wrappers for both IDM and DLM.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
The autoactivation property can be specified in lvcreate
or vgcreate for new LVs/VGs, and the property can be changed
by lvchange or vgchange for existing LVs/VGs.
--setautoactivation y|n
enables|disables autoactivation of a VG or LV.
Autoactivation is enabled by default, which is consistent with
past behavior. The disabled state is stored as a new flag
in the VG metadata, and the absence of the flag allows
autoactivation.
If autoactivation is disabled for the VG, then no LVs in the VG
will be autoactivated (the LV autoactivation property will have
no effect.) When autoactivation is enabled for the VG, then
autoactivation can be controlled on individual LVs.
The state of this property can be reported for LVs/VGs using
the "-o autoactivation" option in lvs/vgs commands, which will
report "enabled", or "" for the disabled state.
Previous versions of lvm do not recognize this property. Since
autoactivation is enabled by default, the disabled setting will
have no effect in older lvm versions. If the VG is modified by
older lvm versions, the disabled state will also be dropped from
the metadata.
The autoactivation property is an alternative to using the lvm.conf
auto_activation_volume_list, which is still applied to to VGs/LVs
in addition to the new property.
If VG or LV autoactivation is disabled either in metadata or in
auto_activation_volume_list, it will not be autoactivated.
An autoactivation command will silently skip activating an LV
when the autoactivation property is disabled.
To determine the effective autoactivation behavior for a specific
LV, multiple settings would need to be checked:
the VG autoactivation property, the LV autoactivation property,
the auto_activation_volume_list. The "activation skip" property
would also be relevant, since it applies to both normal and auto
activation.
Function is not having the best name since it does check
no just raid LVs to be in sync.
Restore the mirror percentage checking - although without retries,
since only raid target is currently known to need it - for other
types it would be ATM a bug to get inconsistent result.
Whiel waiting for raid to return consistent status,
use interruptible sleep - so command can break quickly.
Use lv_raid_status() to get percentage easily from status.
Enabled extension/mixing of stripes/linears, error and zero
segtype LVs with stripes/linear, error and zero segtypes.
It is not very useful in practice, as the user cannot store any real
data on error or zero segtypes, but it may get some uses in
some scenarios where i.e. some portion of the device should not be
readable. Mixing of types happens on 'extent_size' level:
lvcreate -L1 -n lv vg
lvextend --type error -L+1 vg/lv
lvextend --type zero -L+1 vg/lv
lvextend --type linear -L+1 vg/lv
lvextend --type striped -L+1 vg/lv
lvs -o+segtype,seg_size vg
Note: when the type is not specified, the last segment type is
automatically selected.
It's also a small 'can of worms' since we can't tell LVs if
the LV is linear/error/zero or their mixtures. So the meaning behind
them may need some updates.
We already have this types of LV created i.e by:
vgreduce --removemissing --force
where missing LV segments have been replaced by either
error or zero segtype (lvm.conf).
TODO: it might be worth adding a message while such device is activated.
Add some extra code to handle differently sized thin-pool
from thin-pool data volume.
ATM this can't really happen, but once we start to use multiple
commits while resizing stacked LV, we may actually get into
the position, where data LV has been already resized,
but thin-pool stayed with old size.
But for now - report difference as internal error.
Just like with other segtype use this function to get whole
raid status info available per a single ioctl call.
Also it nicely simplifies read of percentage info about
in_sync portion of raid volume.
TODO: drop use of other calls then lv_raid_status call,
since all such calls could already use status - so it just
adds unnecessary duplication.
Reuse similar 'acceleration' as used for dependent volumes also
for snapshot - so when origin is being removed with all thick
snapshots, don't bother with individual 'COW' detachments
and write&commits, and when possible handle this all within
a single commit.
Move code for prompting about removed LV to a single function
and use it also to prompt for removal of origin and all its thick
snapshots and also when removing merging origin.
Function does handle postponed write_and_commit so there is
no 'in-flight' operation while waiting on [y|n] answer.
Compat code and handle unusual case, where
thin snapshot is also a 'thick snapshot origin' and such
snapshot gets merged into a thin origin.
However since now lv_is_visible() (which is complex function)
replaced &VISIBLE_LV check, the whole this check seems to be
no longer useful as sum of all 3 will always match??
Since cached LV is going to be removed together with its cache,
there is not much to gain if we try to flush cache first.
User may use 'vgcfgrestore' to get back origin + cache.
Assuming user is not using issue_discards.
When data are discarded after remove there is nothing to restore!
This change allows to futher reduce number of commits
during lvremove/vgremove.
When lvremove/vgremove removes thin volumes with its thin-pool as well,
try to skip any updates of such thin-pool, so when everything properly
deactivates, there is no message send to this thin-pool and whole
thin-pool is removed with a single commit.
Returning NULL for lv_committed is basically instant crash,
so instead try with passed LV instead.
It shouldn't matter as this is internall error path anyway,
but coverity should be happier.
Another step towards better automatic handling of backup,
and automatically setup needs_backup after commit.
In some next step we should reduce number of backups and takem
then only at the command finish with vg_committed content.
Match VG uuid just once per list of all LVs in VG.
TODO: maybe some more efficeint tree or hash could be better here,
but since it's used not so often, the total benefit is not so great,
so ATM just reducing amount of checked bytes.
Use different 'hint' size for dm_hash_create() call - so
when debug info about hash is printed we can recognize which
hash was in use.
This patch doesn't change actual used size since that is always
rounded to be power of 2 and >=16 - so as such is only a
help to developer.
We could eventually use 'name' arg, but since this would have changed
API and this patchset will be routed to libdm & stable - we will
just use this small trick.
Just like with deactivation, call of 'lv_is_not_in_use()'
now has embeded report for inactivate LV.
Note: this patch cannot be backported to stable-2.02 - as
there lv_is_active() has 'cluster' meaning and differs from lvinfo().
When parsing VG metadata we can create from a single config tree
also 'vg_committed' that is always created for writable VG.
This avoids extra uncessary step of serializing and deserilizing
just parsed VG.
Every vg_write stores new 'metadata' into precommitted slot.
For this step we use 'serialized buffer' to ascii metadata.
Instead of recreating this buffer after whole 'vg_write()' we
use this buffer instantly for creating of precommitted VG.
This has also the advantage of catching any problems with
reparsing of ascii metadata back to VG early before any write.
This patch postpones update of lvm metadata for each removed
LV for later moment depending on LV type.
It also queues messages to be printed after such write & commit.
As such there is some change in the behavior - although before
prompt we do make write&commit happens automatically in some
other error case we rather keep 'existing' state - so there
could be difference in amount of removed & commited LVs.
IMHO introduce logic is slightly better and more save.
But some cases still need the early commit - i.e. thin-removal
and fixing this needs some more thinking.
TODO: improve removal at least with the case of the whole thin-pool.
i.e. we can simply recognize removal of 'all LVs/whole VG'.
Taking backup with each removed LV is slowing down the process
considerable and is largerly uneeded. We are supposed to take
backup only on significant points and making sure the backup
is correct when the command is finished.
TODO: check how many other commands can be improved.
The LVM devices file lists devices that lvm can use. The default
file is /etc/lvm/devices/system.devices, and the lvmdevices(8)
command is used to add or remove device entries. If the file
does not exist, or if lvm.conf includes use_devicesfile=0, then
lvm will not use a devices file. When the devices file is in use,
the regex filter is not used, and the filter settings in lvm.conf
or on the command line are ignored.
LVM records devices in the devices file using hardware-specific
IDs, such as the WWID, and attempts to use subsystem-specific
IDs for virtual device types. These device IDs are also written
in the VG metadata. When no hardware or virtual ID is available,
lvm falls back using the unstable device name as the device ID.
When devnames are used, lvm performs extra scanning to find
devices if their devname changes, e.g. after reboot.
When proper device IDs are used, an lvm command will not look
at devices outside the devices file, but when devnames are used
as a fallback, lvm will scan devices outside the devices file
to locate PVs on renamed devices. A config setting
search_for_devnames can be used to control the scanning for
renamed devname entries.
Related to the devices file, the new command option
--devices <devnames> allows a list of devices to be specified for
the command to use, overriding the devices file. The listed
devices act as a sort of devices file in terms of limiting which
devices lvm will see and use. Devices that are not listed will
appear to be missing to the lvm command.
Multiple devices files can be kept in /etc/lvm/devices, which
allows lvm to be used with different sets of devices, e.g.
system devices do not need to be exposed to a specific application,
and the application can use lvm on its own set of devices that are
not exposed to the system. The option --devicesfile <filename> is
used to select the devices file to use with the command. Without
the option set, the default system devices file is used.
Setting --devicesfile "" causes lvm to not use a devices file.
An existing, empty devices file means lvm will see no devices.
The new command vgimportdevices adds PVs from a VG to the devices
file and updates the VG metadata to include the device IDs.
vgimportdevices -a will import all VGs into the system devices file.
LVM commands run by dmeventd not use a devices file by default,
and will look at all devices on the system. A devices file can
be created for dmeventd (/etc/lvm/devices/dmeventd.devices) If
this file exists, lvm commands run by dmeventd will use it.
Internal implementaion:
- device_ids_read - read the devices file
. add struct dev_use (du) to cmd->use_devices for each devices file entry
- dev_cache_scan - get /dev entries
. add struct device (dev) to dev_cache for each device on the system
- device_ids_match - match devices file entries to /dev entries
. match each du on cmd->use_devices to a dev in dev_cache, using device ID
. on match, set du->dev, dev->id, dev->flags MATCHED_USE_ID
- label_scan - read lvm headers and metadata from devices
. filters are applied, those that do not need data from the device
. filter-deviceid skips devs without MATCHED_USE_ID, i.e.
skips /dev entries that are not listed in the devices file
. read lvm label from dev
. filters are applied, those that use data from the device
. read lvm metadata from dev
. add info/vginfo structs for PVs/VGs (info is "lvmcache")
- device_ids_find_renamed_devs - handle devices with unstable devname ID
where devname changed
. this step only needed when devs do not have proper device IDs,
and their dev names change, e.g. after reboot sdb becomes sdc.
. detect incorrect match because PVID in the devices file entry
does not match the PVID found when the device was read above
. undo incorrect match between du and dev above
. search system devices for new location of PVID
. update devices file with new devnames for PVIDs on renamed devices
. label_scan the renamed devs
- continue with command processing
User use 'lvconvert -Zn --type vdo-pool' to convert an existing
vdo formated volume and skip lvm2 internal formating.
This however requires user is passing proper matching parameters.
For them user can use --profile|--metadataprofile option whos
support has been also enhanced.
TODO: add support to read values directly from formated volume.
In some cases we use 'creation' also during conversion.
Here it can be actually unwanted side effect we may remove
not just newly created layers - but also original converted LV.
So until we make clear how to properly revert from some errors
in middle of conversion, disable removal for any 'lvconvert' commands.
Automatically figure out resizable layer in the LV stack and
resize it online.
Split check for reshaped raids and postpone removal of
unused space after finished reshaping after metadata archiving.
Drop warning about unsupported automatic resize of monitored thin-pool.
Currently there is not yet support for resize of writecache.
Move extra md component detection into the label scan phase.
It had been in set_pv_devices which was deep within the vg_read
phase, which wasn't a good place (better to detect that earlier.)
Now that pv metadata info is available in the scan phase, the pv
details (size and device_hint) can be used for extra md checking.
Use the device_hint from the pv metadata to trigger a full md
component check if the device_hint begins with /dev/md.
Stop triggering full md component checks based on missing
udev info for a dev.
Changes to tests to reflect that the code is now detecting
md components in some test case that it wasn't before.
Current allocation limitation requires to fit metadata/log LV on
a single PV. This is usually not a big problem, but since
thin-pool and cache-pool is using this for allocating extents
for their metadata LVs it might be eventually causing errors
where the remaining free spaces for large metadata size is spread
over several PV.
When passing 'pvmove --name arg' try to automatically move
all associated dependencies with given LV.
i.e. 'pvmove --name thinpool vg vgnew'
moves all thins and data and metadata LV into a new VG vgnew.
Use update_pool_metadata_min_max() which is shared with
thin-pool metadata min-max updating.
Gives improved messages when converting volumes to metadata.
There is not much point to let allocate more then this size
even when i.e. converted LV is bigger then 16GiB (%extent_size)
ATM neither thin-pool nor cache-pool supports bigger metadata.
Initial support for thin-pool used slightly smaller max size 15.81GiB
for thin-pool metadata. However the real limit later settled at 15.88GiB
(difference is ~64MiB - 16448 4K blocks).
lvm2 could not simply increase the size as it has been using hard cropping
of the loaded metadata device to avoid warnings printing warning of kernel
when the size was bigger (i.e. due to bigger extent_size).
This patch adds the new lvm.conf configurable setting:
allocation/thin_pool_crop_metadata
which defaults to 0 -> no crop of metadata beyond 15.81GiB.
Only user with these sizes of metadata will be affected.
Without cropping lvm2 now limits metadata allocation size to 15.88GiB.
Any space beyond is currently not used by thin-pool target.
Even if i.e. bigger LV is used for metadata via lvconvert,
or allocated bigger because of to large extent size.
With cropping enabled (=1) lvm2 preserves the old limitation
15.81GiB and should allow to work in the evironement with
older lvm2 tools (i.e. older distribution).
Thin-pool metadata with size bigger then 15.81G is now using CROP_METADATA
flag within lvm2 metadata, so older lvm2 recognizes an
incompatible thin-pool and cannot activate such pool!
Users should use uncropped version as it is not suffering
from various issues between thin_repair results and allocated
metadata LV as thin_repair limit is 15.88GiB
Users should use cropping only when really needed!
Patch also better handles resize of thin-pool metadata and prevents resize
beoyond usable size 15.88GiB. Resize beyond 15.81GiB automatically
switches pool to no-crop version. Even with existing bigger thin-pool
metadata command 'lvextend -l+1 vg/pool_tmeta' does the change.
Patch gives better controls 'coverted' metadata LV and
reports less confusing message during conversion.
Patch set also moves the code for updating min/max into pool_manip.c
for better sharing with cache_pool code.
When detaching writecache, make the first stage send a message
to dm-writecache to set the cleaner option. This is instead of
reloading the dm table with the cleaner option set. Reloading
the table causes udev to process/probe the dm dev, which gets
stalled because of the writeback activity, and the stalled udev
in turn stalls the lvconvert command when it tries to sync with
udev events.
When getting writecache status we do not need to get
open_count or read_head info, which can cause extra steps.
In case legs of a raid0 LV are removed, the lvdisplay command still
reports 'available' though raid0 is not providing any resilience
compared to the other raid levels.
Also lvdisplay does not display '(partial)' in case of missing raid0
legs as oposed to the lvs command.
Enhance lvdisplay to report "NOT available" for any RaidLV type in case
too many legs are inaccessible hence causing data loss. I.e. any leg
for raid0, all for raid1, more than 1 for raid4/5, more than 2 for raid6
and in case of completely lost mirror groups for raid10.
Add test/shell/lvdisplay-raid.sh.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1872678
New VDO targets v6.2.3 corrects support for online rename of VDO device.
If needed if can be disable via new lvm.conf setting:
vdo_disabled_features = [ "online_rename" ]
When removing pool LV from a stacked LV setup, it's been possible
to leak _pmspare and such hidden LV then required manual
user removal.
Fix it by moving automatic removal into _lv_reduce().
When adding replacement raid+integrity images (lvconvert --repair
after a raid image is lost), various errors can cause the function
to exit with an error. On this exit path, the function attempts
to revert new images that had been created but not yet used. The
cleanup failed to account for the fact that not all images needed
to be reverted.
Since commit 77fdc17d70 always include
log_len size into needed extents - however now we may need sometimes
more extents then necessary - mainly when multiple PVs are involved
into allocation.
Add logs_still_needed into calculation of sufficient_pes_free()
When a writecache sublv or an integrity metadata sublv
are partial (missing a dev), set the partial flag on
the upper level LV also, as is done for other sublvs.
When using cache with a cachevol, the cache_check tool was
not being run on the cache metadata during activation.
cache_check clears the needs_check flag in the cache
metadata, so if the flag was set due to an unclean
shutdown, the activation would fail.
Each integrity image in a raid LV reports its own number
of integrity mismatches, e.g.
lvs -o integritymismatches vg/lv_rimage_0
lvs -o integritymismatches vg/lv_rimage_1
In addition to this, allow the total number of integrity
mismatches from all images to be displayed for the raid LV.
lvs -o integritymismatches vg/lv
shows the number of mismatches from both lv_rimage_0 and
lv_rimage_1.
In some cases the dev size may not have been read yet
in set_pv_devices(). In this case get the dev size
before comparing the dev size with the pv size.
Since BLKZEROOUT ioctl should be supposedly fastest
way how to clear block device start using this ioctl
for zeroing a device. Commonly we do zero typically
small portion of a device (8KiB) - however since we now
also started to zero metadata devices, in the case
of i.e. thin-pool metadata this can go upto ~16GiB
and here the performance starts to be noticable.
Since dev_set_bytes() now closes dev on error path itself,
remove this unneeded call now (introduced few commits back
in history thus removing comment from WHATS_NEW)
When detaching a writecache, use the cleaner setting
by default to writeback data prior to suspending the
lv to detach the writecache. This avoids potentially
blocking for a long period with the device suspended.
Detaching a writecache first sets the cleaner option, waits
for a short period of time (less than a second), and checks
if the writecache has quickly become clean. If so, the
writecache is detached immediately. This optimizes the case
where little writeback is needed.
If the writecache does not quickly become clean, then the
detach command leaves the writecache attached with the
cleaner option set. This leaves the LV in the same state
as if the user had set the cleaner option directly with
lvchange --cachesettings cleaner=1 LV.
After leaving the LV with the cleaner option set, the
detach command will wait and watch the writeback progress,
and will finally detach the writecache when the writeback
is finished. The detach command does not need to wait
during the writeback phase, and can be canceled, in which
case the LV will remain with the writecache attached and
the cleaner option set. When the user runs the detach
command again it will complete the detach.
To detach a writecache directly, without using the cleaner
step (which has been the approach previously), add the
option --cachesettings cleaner=0 to the detach command.
Introduce structures lv_status_thin_pool and
lv_status_thin (pair to lv_status_cache, lv_status_vdo)
Convert lv_thin_percent() -> lv_thin_status()
and lv_thin_pool_percent() + lv_thin_pool_transaction_id() ->
lv_thin_pool_status().
This way a function user can see not only percentages, but also
other important status info about thin-pool.
TODO:
This patch tries to not change too many other things,
but pool_below_threshold() now uses new thin-pool info to return
failure if thin-pool cannot be actually modified.
This should be handle separately in a better way.
Improve error response and reporting, when creating thin snapshots.
If the thin pool kernel metadata already have device with ID lvm2
tries to create, give more meanigful error message and also properly
restore transaction id to the value known to thin-pool in this case.
Before it's been possible to divert by one from kernel TID value,
and lvm2 stacked delete message for such thin device.
Since ATM kernel does not support this operation,
disable 'lvrename' of an active vdopool.
As a workaround, user may simply deactivate, rename and activate.
When user tries to extend vdo pool - he needs to go always
at least by 1 full VDO slab (defined as vdo_slab_size_mb).
To avoid all trouble around find 'workable' size - lvm2 automatically
increases the passed (or by --use-policies calculated) extension size
(and informs a user about sometimes possibly large increase as slab
size can go upto 32GiB)
With VDO users need to always 'think-big' anyway and expect such
operation to be in GiB domain range.
When thetable reload fails during suspend() - we were only calling
plain resume() - and this will reload only those devices,
which were left suspend, but will not try to restore
metadata state according to lvm2 reverted metadata.
So if we were reloading device tree - we have restored
only top-level LV and rest of reverted device manipulation
were left alone and possibly mismatched what is in committed
metadata.
FIXME: There are several cases were such revert will likely not work
properly anyway as some operation are currenly handled in single commit,
while they need multiple commits, but it's step towards better correctness.
At least we catch there errors now earlier.
lvm opens devices readonly to scan them, but
needs to open then readwrite to update the metadata.
Previously, the ro fd was closed before the rw fd
was opened, leaving a small gap where the dev was
not held open, and during which the dev could
possibly change which storage it referred to.
With the bcache_change_fd() interface, lvm opens a
rw fd on a device to be written, tells bcache to
change to the new rw fd, and closes the ro fd.
. open dev ro
. read dev with the ro fd (label_scan)
. lock vg (ex for writing)
. open dev rw
. close ro fd
. rescan dev to check if the metadata changed
between the scan and the lock
. if the metadata did change, reread in full
. write the metadata
Add a "device index" (di) for each device, and use this
in the bcache api to the rest of lvm. This replaces the
file descriptor (fd) in the api. The rest of lvm uses
new functions bcache_set_fd(), bcache_clear_fd(), and
bcache_change_fd() to control which fd bcache uses for
io to a particular device.
. lvm opens a dev and gets and fd.
fd = open(dev);
. lvm passes fd to the bcache layer and gets a di
to use in the bcache api for the dev.
di = bcache_set_fd(fd);
. lvm uses bcache functions, passing di for the dev.
bcache_write_bytes(di, ...), etc.
. bcache translates di to fd to do io.
. lvm closes the device and clears the di/fd bcache state.
close(fd);
bcache_clear_fd(di);
In the bcache layer, a di-to-fd translation table
(int *_fd_table) is added. When bcache needs to
perform io on a di, it uses _fd_table[di].
In the following commit, lvm will make use of the new
bcache_change_fd() function to change the fd that
bcache uses for the dev, without dropping cached blocks.
