IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
pvscan --cache -aay was activating LVs in exported VGs
when it should not.
It appears that this was a regression from commit 9b640c3684
"pvscan: use process_each_vg for autoactivate".
(Automatic) repair may not be allowed during the initial sync of an upconverted
linear LV, because the data on the failing, primary leg hasn't been completely
synchronized to the N-1 other legs of the raid1 LV (replacing failed legs during
repair involves discontinuing access to any replaced legs data, thus preventing
data recovery on the primary leg e.g. via dd_rescue).
Even though repair would not cause data loss when adding legs to a fully synced
raid1 LV, we don't have information yet defining this state yet (e.g. a raid1
LV flag telling the fully synchronized status before any legs were added),
hence can't automatically decide to allow to repair.
If nonetheless a repair on a non-synced raid1 LVs is intended, the "--force"
option has to be provided.
Resolves: rhbz1311765
Validate kernel support for raid0/raid4 on given and
requested segtype before requesting conversions on them.
Because raid10 wasn't present in old RAID targets, add
the same validation to be prepared once we support them.
Check for dm-raid target version with non-standard raid4 mapping expecting the dedicated
parity device in the last rather than the first slot and prohibit to create, activate or
convert to such LVs from striped/raid0* or vice-versa in order to avoid data corruption.
Add related tests to lvconvert-raid-takeover.sh
Resolves: rhbz1388962
On conversions between striped/raid0* and raid4, the kernel expects
the dedicated raid4 parity SubLVs in the first segment area rather than
in the last it's been allocated to, thus the data mapping ain't proper.
Enhance lvconvert (lib/metadata/raid_manip.c) to shift the dedicated
parity SubLVs on conversions from striped/raid0* to raid4 and vice-versa.
In case of raid0_meta -> raid4 where the MD raid0 personality already has
stored RAID array device positions in the superblocks, the MetaLVs have to
be cleared so that the kernel doesn't fail validating the array positions
after lvm has shifted them up by one.
Add more tests to lvconvert-raid-takeover.sh including one to check for
mapping flaws by converting a created raid4 with filesystem -> striped
and fsck it.
Whilst on it:
- add missing direct striped -> raid4 conversion to the takeover array
to avoid an intermim conversion from striped -> raid0*
- clean up the takeover array
- allow lvconvert to actually call lv_raid_convert() on all takeover requests
in order to check parameters and display messages provided by takeover
functions rather than just "...not supported" from within lvconvert
- fix a typo
Resolves: rhbz1386148
If a device disappears after obtaining the list of devices but before
processing it as a member of that list, dmsetup exits with a failure code.
Most commands still produce what output they can in these circumstances,
but 'ls --tree' and 'info -c' with fields depending on device dependencies
didn't. Change this.
Keep for now function logic making its decision on string content.
We need bigger patch converting all things to bit-checks later.
This needs however bigger refactoring.
So this commit reverts some changes from:
c8b6c13015
Commit 088b3d036a allowed repair on cache origin RAID LVs
and restricted lvconvert actions on RAID SubLVs to change number of mirrors, repair,
replace and type changes in order to avoid unsuitable coversions on them.
This introduced a regression prohibiting --splitmirrors on any RAID SubLVs
(e.g. of cache or thin LVs; lvconvert-{cache,thin}-raid.sh tests failing).
Fix allows split mirrors again.
Fix some indenting whilst on it.
When we have already decoded arg_is_set into a local var
or already set segment type - already use these
values instead of repeating calls and string checks.
Seems some error path where not converted to 'new' ECMD return value.
Fix them to always 'goto out'.
Also drop unneeded 'ret = 0' when ret already is 0.
In case a RAID orig LV is being cached and fails, repair is impossible because
"lvconvert --repair" gets rejected.
Fix by allowing repair on cache orig RAID LVs and
"lvconvert --replace/--mirrors/--type {raid*|mirror|striped|linear}" as well.
Allow the same lvconvert actions on any cache pool and metadata RAID SubLVs.
Resolves: rhbz1380532
Make sure that the temporary dm_histogram used for the bounds
argument is freed in the case that the user provided a --bounds
argument on the command line.
The dm-raid target now rejects device rebuild requests during ongoing
resynchronization thus causing 'lvconvert --repair ...' to fail with
a kernel error message. This regresses with respect to failing automatic
repair via the dmeventd RAID plugin in case raid_fault_policy="allocate"
is configured in lvm.conf as well.
Previously allowing such repair request required cancelling the
resynchronization of any still accessible DataLVs, hence reasoning
potential data loss.
Patch allows the resynchronization of still accessible DataLVs to
finish up by rejecting any 'lvconvert --repair ...'.
It enhances the dmeventd RAID plugin to be able to automatically repair
by postponing the repair after synchronization ended.
More tests are added to lvconvert-rebuild-raid.sh to cover single
and multiple DataLV failure cases for the different RAID levels.
- resolves: rhbz1371717
Reload of thin-pool origin_only is designed to only post messages
to a thin-pool. It's not intended to be used for reload of thin-pool
table. Fix it by using standard call 'lv_update_and_reload()'.
Reinstantiate reporting of metadata percent usage for cache volumes.
Also show the same percentage with hidden cache-pool LV.
This regression was caused by optimization for a single-ioctl in
2.02.155.
Allow RAID scrubbing on cache origin sub-LV
This patch adds the ability to perform RAID scrubbing on the cache
origin sub-LV (https://bugzilla.redhat.com/1169495). Cache origin
operations are restricted to non-clustered RAID LVs until there can
be further testing in a cluster (even for exclusive activation).
User can either specify directly _corig LV
or he can specify cache LV and operation --syncation is
passed ONLY to _corig LV.
If users wants to manipulation with cache-pool devices - he
needs to specify this object name.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Introduce 'hard limit' for max number of cache chunks.
When cache target operates with too many chunks (>10e6).
When user is aware of related possible troubles he
may increase the limit in lvm.conf.
Also verbosely inform user about possible solution.
Code works for both lvcreate and lvconvert.
Lvconvert fully supports change of chunk_size when caching LV
(and validates for compatible settings).
Commit e947c362dd introduced
config_settings.h file for central place to store all definitions for
config options. By mistake, it used report/colums_as_rows instead
of report/columns_as_rows (missing "n" in "columns").
If the number of stripes requested is incompatible with the requested
type of raid, give an error instead of adjusting it.
If no stripes argument is supplied, continue to use an appropriate
default.
a579ba2ac2 fixed a regression causing a segfault if no external
origin existed but broke the logic leading to erroneous error
messages and creations of split off exported VGs in case the
external origin and the pool LVs were allocated on different PVs.
- resolves rhbz1367459
Creating a RaidLV in VGs with very small extent sizes caused
late failure in the kernel giving a not very informative error
message. Catch the attempt early and display failure message
'Unable to create RAID LV: requires minimum VG extent size 4.00 KiB'.
- resoves rhbz1179970
'pvmove -n name pv1 pv2' called with the name of a top-level LV
failed with mentioned commit.
Enhance pvmove-raid-segtypes.sh to test for prohibited RAID SubLV moves.
'pvmove -n name pv1 pv2' allows to collocate multiple RAID SubLVs
on pv2 (e.g. results in collocated raidlv_rimage_0 and raidlv_rimage_1),
thus causing loss of resilence and/or performance of the RaidLV.
Fix this pvmove flaw leading to potential data loss in case of PV failure
by preventing any SubLVs from collocation on any PVs of the RaidLV.
Still allow to collocate any DataLVs of a RaidLV with their sibling MetaLVs
and vice-versa though (e.g. raidlv_rmeta_0 on pv1 may still be moved to pv2
already holding raidlv_rimage_0).
Because access to the top-level RaidLV name is needed,
promote local _top_level_lv_name() from raid_manip.c
to global top_level_lv_name().
- resolves rhbz1202497
Enforce mirror/raid0/1/10/4/5/6 type specific maximum images when
creating LVs or converting them from mirror <-> raid1.
Document those maxima in the lvcreate/lvconvert man pages.
- resolves rhbz1366060
Some settings are not suitable for override in interactive/shell
mode because such settings may confuse the code and it may end
up with unexpected behaviour. This is because of the fact that
once we're in the interactive/shell mode, we have already applied
some settings for the shell itself and we can't override them
further because we're already using those settings to drive the
interactive/shell mode. Such settings would get ignored silently
or, in worse case, they would mess up the existing configuration.
