IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Update makefile to link with more libs since now whole liblvm-internal.a
is linked-in and this library has futher dependencies.
Avoid including deps for run-unit-test.
Drop linking separate status.c as it's already linked via internal libs.
Check allocation of thin-pool works on 2PVs, when one is so full,
that even metadata do not fit there (as they need at least 2M,
while 99% of 63MB fills >62MB)
The md filter can operate in two native modes:
- normal: reads only the start of each device
- full: reads both the start and end of each device
md 1.0 devices place the superblock at the end of the device,
so components of this version will only be identified and
excluded when lvm uses the full md filter.
Previously, the full md filter was only used in commands
that could write to the device. Now, the full md filter
is also applied when there is an md 1.0 device present
on the system. This means the 'pvs' command can avoid
displaying md 1.0 components (at the cost of doubling
the i/o to every device on the system.)
(The md filter can operate in a third mode, using udev,
but this is disabled by default because there have been
problems with reliability of the info returned from udev.)
With the move to top-level makefile - there are some issues
with subdir recursive makefile.
Make the building more tolerant for now until fully resolved.
Add tests for linear <-> striped|raid* conversions.
Add region_size config to reshape tests to avoid test
failures in case of it being defined unexpectedly in lvm.conf.
Related: rhbz1439925
Related: rhbz1447809
We have been warning about duplicate devices (and disabling lvmetad)
immediately when the dup was detected (during label_scan). Move the
warnings (and the disabling) to happen later, after label_scan is
finished.
This lets us avoid an unwanted warning message about duplicates
in the special case were md components are eliminated during the
duplicate device resolution.
This minor patch fixes grammar in a few messages which get
printed to users. It also fixes the same grammar mistake in
several comments.
Signed-off-by: Rick Elrod <relrod@redhat.com>
--
The device-mapper directory now holds a copy of libdm source. At
the moment this code is identical to libdm. Over time code will
migrate out to appropriate places (see doc/refactoring.txt).
The libdm directory still exists, and contains the source for the
libdevmapper shared library, which we will continue to ship (though
not neccessarily update).
All code using libdm should now use the version in device-mapper.
Unfortunatelly on kernels <4.16 lvm2 can't user brd ramdisks
for backend device as number of test is failing with this kernel
message:
device-mapper: ioctl: can't change device type after initial table load.
caused by DAX request-based handling, and lvm2 tries to replace device
with backend 'error' bio-based device and such table reload is being
rejected.
So ATM keep ramdisk only on most recent kernel to experiment a bit,
for older machines just stay safe and keep old slower loop backend.
As we start refactoring the code to break dependencies (see doc/refactoring.txt),
I want us to use full paths in the includes (eg, #include "base/data-struct/list.h").
This makes it more obvious when we're breaking abstraction boundaries, eg, including a file in
metadata/ from base/
While newer system can detect need for 4K mkfs, on older test machines
running test suite over 4k is reporting problems.
Some more generic solution is needed thought.
When test happens to run in tmpfs, it cannot use O_DIRECT (unsupported
with tmpfs).
CHECKME: unsure if detection of tmpfs is 'valid' but kind of works and
is very simple.
As Makefiles already do use target with name 'device-mapper'
rename this new device-mapper dir to non-conflicting name.
We also seem to already use '_' in other dir names.
Also rename device_mapper/Makefile to source for generating Makefile.in
so we can use it for build in other source dirs properly.
It's very hard to use some 'non-recurive' Makefiles with
rest of system running 'recursively'.
So ATM drop inclusion of subdir makefile and add support
for 2 new top-level targets:
unit-test (builds test/unit dir)
run-unit-test (build & run test/unit/unit-test run)
Just like 52656c89fd
when now cache is compiled in 'unditionally'.
This patch is actually enforce by changes in
commit: 2bc896f2a3
where CACHE value is not set anymore.
If the test does not need root, it can use 'SKIP_ROOT_DM_CHECK'.
For such test no actions needed root to initilize DM devices and
nodes will be take and test can check i.e. functional unit tests.
Usage of dm_delay looks to be slowing not just 'delayed' portion
of device, but due to the fact it's also slows down ANY flush
operation on such device it's overal speed impact is huge.
In some case we can however user other methods to slowdown disk writes,
in case of old dm 'mirror' target we can throttle I/O of mirror
synchronisation giving the next commands enough time to test couple
race conditions.
Usage:
throttle_dm_mirror [percentage]
Thtrottle down sync speed (lowest is '1' which is also default when
unspecified)
restore_dm_mirror
Restores the value of throttling before call of 'throttle_dm_mirror'
Usually it should '100'
Currently usage of loop device over backend file in ramdisk (tmpfs)
is actually causing unnecassary memory consution, since just
reading such loop device is causing RAM provisioning.
This patch add another possible way how to use ramdisk directly
through 'brd' device when possible (and allowed).
This however has it's limitation as well - brd does not support
TRIM, so the only way how to erase is to remove brd module ??
Alse there is 4K sector size limitation imposed by ramdisk.
Anyway - for some mirror test that were using large amount of
disk space (tens of MB) this brings noticable speed boost.
(But could be worth to solve the slowness of loop in kernel?)
To prevent using 'brd' for testing set LVM_TEST_PREFER_BRD=0
like this:
make check_local LVM_TEST_PREFER_BRD=0
This test can't use brd (ramdisk) as backend since for some
weird reason lsblk is not listing these device.
TODO: test could be probably rewritten to avoid using lsblk somehow??
When the backend device supports only 4K blocks (like ramdisk)
we cannot use for testing any smaller blocksize.
So recalc test for 4K extent size.
We may possibly introduce one list extra test that
can be executed on devices with 512b sectors to
check lvm2 support those min extent sizes...
An implementation of an adaptive radix tree. Has the following nice
properties:
- At least as fast as the hash table
- Uses less memory
- You don't need to give an expected size when you create
- It scales nicely (ie. no large reallocations like the hash table).
- You can iterate the keys in lexicographical order.
Only insert and lookup are implemented so far. Plus there's a lot
more performance to come.
In case "lvconvert -mN RaidLV" was used on a degraded
raid1 LV, success was returned instead of an error.
Provide message to inform about the need to repair first
before changing number of mirrors and exit with error.
Add new lvconvert-m-raid1-degraded.sh test.
Resolves: rhbz1573960
