IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
When lvconvert adds a new leg - it's doing it free 'temporary' image
layer - however this temporary 'internal' mirror is also MIRRORED LV.
But the status bit was not properly transfered through layer.
Do not emit warning message but only log debug message if
lvm2-lvmdbusd.service unit is missing and at the same time
we have global/notify_dbus=1 (which is used by default if we
configured sources with "--enable-notify-dbus"). We don't want
hard dependency between LVM2 and lvmdbusd so it's enough to log
only debug message in this case.
Make it easier to replace missing segments with 'zero' returning
target - otherwise user would have to create some extra target
to provide zeros as /dev/zero can't be used (not a block device).
Also break code loop when segment is found and make it an INTERNAL_ERROR
where it's missing.
Instead of clearing multiple rmeta device with sequential activation
process and waiting for udev for every _rmeta device separately,
activate all _rmeta devices first and then clear them and deactivate
afterwards.
Also update some tracing messages.
When anyhing goes wrong during clearing process, always try to
deactivate as much _rmeta devices as possible before fail.
Translate log_info() into log_very_verbose() which is macro
supposed to be used by our code.
log_info() is internal macro with eventually some 'symbolic' meaning
in syslogging daemons.
Introduce macros:
log_level(), log_stderr(), log_once(), log_bypass_report()
For easier and more consisten way how to 'decoder' bits
of info from passed 'level'.
This patch fixes potential problem when 'level' of message
might not have always masked right bits.
(Automatic) repair may not be allowed during the initial sync of an upconverted
linear LV, because the data on the failing, primary leg hasn't been completely
synchronized to the N-1 other legs of the raid1 LV (replacing failed legs during
repair involves discontinuing access to any replaced legs data, thus preventing
data recovery on the primary leg e.g. via dd_rescue).
Even though repair would not cause data loss when adding legs to a fully synced
raid1 LV, we don't have information yet defining this state yet (e.g. a raid1
LV flag telling the fully synchronized status before any legs were added),
hence can't automatically decide to allow to repair.
If nonetheless a repair on a non-synced raid1 LVs is intended, the "--force"
option has to be provided.
Resolves: rhbz1311765
Check for dm-raid target version with non-standard raid4 mapping expecting the dedicated
parity device in the last rather than the first slot and prohibit to create, activate or
convert to such LVs from striped/raid0* or vice-versa in order to avoid data corruption.
Add related tests to lvconvert-raid-takeover.sh
Resolves: rhbz1388962
On conversions between striped/raid0* and raid4, the kernel expects
the dedicated raid4 parity SubLVs in the first segment area rather than
in the last it's been allocated to, thus the data mapping ain't proper.
Enhance lvconvert (lib/metadata/raid_manip.c) to shift the dedicated
parity SubLVs on conversions from striped/raid0* to raid4 and vice-versa.
In case of raid0_meta -> raid4 where the MD raid0 personality already has
stored RAID array device positions in the superblocks, the MetaLVs have to
be cleared so that the kernel doesn't fail validating the array positions
after lvm has shifted them up by one.
Add more tests to lvconvert-raid-takeover.sh including one to check for
mapping flaws by converting a created raid4 with filesystem -> striped
and fsck it.
Whilst on it:
- add missing direct striped -> raid4 conversion to the takeover array
to avoid an intermim conversion from striped -> raid0*
- clean up the takeover array
- allow lvconvert to actually call lv_raid_convert() on all takeover requests
in order to check parameters and display messages provided by takeover
functions rather than just "...not supported" from within lvconvert
- fix a typo
Resolves: rhbz1386148
Works if the pool is inactive.
Activation code doesn't notice a new raid dependency in on-disk metadata
when a thin LV is already active.
https://bugzilla.redhat.com/1365286
We added lightweight toolcontext handle to avoid useless initialization
of some parts of the context and also to avoid problems when using the
handle very soon at system boot, like in lvm2-activation-generator
through lvm2app interface. However, we missed reading all the other
config sources like lvmlocal.conf as well as any tag config - we need to
read these too to get the final config value which may be overriden in
any of these additional config sources.
Currently, we use this lightweight toolcontext handle to read
global/use_lvmetad and global/use_lvmpolld config values in
lvm2-activation-generator using lvm2app interface (lvm_config_find_bool
lvm2app function).
The dm-raid target now rejects device rebuild requests during ongoing
resynchronization thus causing 'lvconvert --repair ...' to fail with
a kernel error message. This regresses with respect to failing automatic
repair via the dmeventd RAID plugin in case raid_fault_policy="allocate"
is configured in lvm.conf as well.
Previously allowing such repair request required cancelling the
resynchronization of any still accessible DataLVs, hence reasoning
potential data loss.
Patch allows the resynchronization of still accessible DataLVs to
finish up by rejecting any 'lvconvert --repair ...'.
It enhances the dmeventd RAID plugin to be able to automatically repair
by postponing the repair after synchronization ended.
More tests are added to lvconvert-rebuild-raid.sh to cover single
and multiple DataLV failure cases for the different RAID levels.
- resolves: rhbz1371717
Commit 199697accf rerouted funtion
for priting cache volume origin to lvm2app app function - which
however had a bug. So restore the original functionality
and print correct LV as cache origin LV.
Unconditionally guard there is at least 1/4 of metadata volume
free (<16Mib) or 4MiB - whichever value is smaller.
In case there is not enough free space do not let operation proceed and
recommend thin-pool metadata resize (in case user has not
enabled autoresize, manual 'lvextend --poolmetadatasize' is needed).
In the case there is no active thin volume, report thin pool
as lock holder. This fixed function like lvextend
which either expecte lock holder LV is some active thin
or 'possibly' inactive thin pool.
The existing code doesn't understand that mirror logs should cling to
parallel LVs (like extending them) instead of avoiding them.
As a quick workaround to avoid lvcreate failures, hard-code
--alloc normal for mirror logs even if the rest of the allocation
used a stricter policy.
https://bugzilla.redhat.com/show_bug.cgi?id=1376532
When rescanning a VG from disk, the metadata read from
each PV was compared as a sanity check. The comparison
is done by exporting the vg metadata from each dev to
a config tree, and then comparing the config trees.
The function to create the config tree inserts
extraneous information along with the actual VG metadata.
This extra info includes creation_time. The config
trees for two devs can easily be created one second
apart in which case the different creation_times would
cause the metadata comparison to fail. The fix is to
exclude the extraneous info from the metadata comparison.
Reinstantiate reporting of metadata percent usage for cache volumes.
Also show the same percentage with hidden cache-pool LV.
This regression was caused by optimization for a single-ioctl in
2.02.155.
Older udev versions (udev < v165), don't have the official
udev_device_get_is_initialized function available to query for
device initialization state in udev database. Also, devices don't
have USEC_INITIALIZED udev db variable set - this is bound to the
udev_device_get_is_initialized fn functionality.
In this case, check for "DEVLINKS" variable instead - all block devices
have at least one symlink set for the node (the "/dev/block/<major:minor>".
This symlink is set by default basic udev rules provided by udev directly.
We'll use this as an alternative for the check that initial udev
processing for a device has already finished.
It's possible (mainly during boot) that udev has not finished
processing the device and hence the udev database record for that
device is still marked as uninitialized when we're trying to look
at it as part of multipath component check in pvscan --cache code.
So check several times with a short delay to wait for the udev db
record to be initialized before giving up completely.
When scanning devs to populate lvmetad during system startup,
filter-mpath with native sysfs multipath component detection
may not detect that a dev is multipath component. This is
because the multipath devices may not be set up yet.
Because of this, pvscan will scan multipath components during
startup, will see them as duplicate PVs, and will disable
lvmetad. This will leave lvmetad disabled on systems using
multipath, unless something or someone runs pvscan --cache
to rescan.
To avoid this problem, the code that is scanning devices to
populate lvmetad will now check the udev db to see if a
dev is a multipath component that should be skipped.
(This may not be perfect due to inherent udev races, but will
cover most cases and will be at least as good as it's ever
been.)
Avoid monitoring of activated cache-pool - where the only purpose ATM
is to clear metadata volume which is actually activate in place
of cache-pool name (using public LV name).
Since VG lock is held across whole clear operation, dmeventd cannot
be used anyway - however in case of appliction crash we may
leave unmonitored device.
In future we may provide better mechanism as the current name
replacemnet is creating 'uncommon' table setups in case the metadata
LV is more complex type like raid (needs some futher thinking about
error path results).
Another point to think about is the fact we should not clear device
while holding lock (i.e. dmeventd mirror repair cannot work in cases
like this).
Introduce 'hard limit' for max number of cache chunks.
When cache target operates with too many chunks (>10e6).
When user is aware of related possible troubles he
may increase the limit in lvm.conf.
Also verbosely inform user about possible solution.
Code works for both lvcreate and lvconvert.
Lvconvert fully supports change of chunk_size when caching LV
(and validates for compatible settings).
Commit e947c362dd introduced
config_settings.h file for central place to store all definitions for
config options. By mistake, it used report/colums_as_rows instead
of report/columns_as_rows (missing "n" in "columns").
'pvmove -n name pv1 pv2' allows to collocate multiple RAID SubLVs
on pv2 (e.g. results in collocated raidlv_rimage_0 and raidlv_rimage_1),
thus causing loss of resilence and/or performance of the RaidLV.
Fix this pvmove flaw leading to potential data loss in case of PV failure
by preventing any SubLVs from collocation on any PVs of the RaidLV.
Still allow to collocate any DataLVs of a RaidLV with their sibling MetaLVs
and vice-versa though (e.g. raidlv_rmeta_0 on pv1 may still be moved to pv2
already holding raidlv_rimage_0).
Because access to the top-level RaidLV name is needed,
promote local _top_level_lv_name() from raid_manip.c
to global top_level_lv_name().
- resolves rhbz1202497
Adding MetaLVs to given DataLVs (e.g. raid0 -> raid0_meta takeover),
_avoid_pvs_with_other_images_of_lv() was missing code to prohibit
allocation when called with a just allocated MetaLV to prohibit
collaocation of the next allocated MetaLV on the same PV.
- resolves rhbz1366738
When lvm is compiled with --enable-notify-dbus and a user uses lvm
shell, after they issue 200+ commands the lvm shell will hang for
~30 seconds trying to notify the lvm dbus service that a change
has occurred. This appears to be caused by resource exhaustion,
because the sockets used for dbus communication are not be closed.
Enforce mirror/raid0/1/10/4/5/6 type specific maximum images when
creating LVs or converting them from mirror <-> raid1.
Document those maxima in the lvcreate/lvconvert man pages.
- resolves rhbz1366060
Some settings are not suitable for override in interactive/shell
mode because such settings may confuse the code and it may end
up with unexpected behaviour. This is because of the fact that
once we're in the interactive/shell mode, we have already applied
some settings for the shell itself and we can't override them
further because we're already using those settings to drive the
interactive/shell mode. Such settings would get ignored silently
or, in worse case, they would mess up the existing configuration.
When lvm commands are executed in lvm shell, we cover the whole lvm
command execution within this shell now. That means, all messages logged
and status caught during each command execution is now recorded in the
log report, including overall command's return code.
With patches that will follow, this will make it possible to widen log
report coverage when commands are executed from lvm shell so the amount
of messages that may end up in stderr/stdout instead of log report are
minimized.
Add new log_context=shell and with log_object_type=cmd and
log_object_name=<command_name> for command log report to collect
overall return code from last command (this is reported under
log_type=status).
Currently, the output is separated in 3 parts and each part can go into
a separate and user-defined file descriptor:
- common output (stdout by default, customizable by LVM_OUT_FD environment variable)
- error output (stderr by default, customizable by LVM_ERR_FD environment variable)
- report output (stdout by default, customizable by LVM_REPORT_FD environment variable)
For example, each type of output goes to different output file:
[0] fedora/~ # export LVM_REPORT_FD=3
[0] fedora/~ # lvs fedora vg/abc 1>out 2>err 3>report
[0] fedora/~ # cat out
[0] fedora/~ # cat err
Volume group "vg" not found
Cannot process volume group vg
[0] fedora/~ # cat report
LV VG Attr LSize Layout Role CTime
root fedora -wi-ao---- 19.00g linear public Wed May 27 2015 08:09:21
swap fedora -wi-ao---- 500.00m linear public Wed May 27 2015 08:09:21
Another example in LVM shell where the report goes to "report" file:
[0] fedora/~ # export LVM_REPORT_FD=3
[0] fedora/~ # lvm 3>report
(in lvm shell)
lvm> vgs
(content of "report" file)
[1] fedora/~ # cat report
VG #PV #LV #SN Attr VSize VFree
fedora 1 2 0 wz--n- 19.49g 0
(in lvm shell)
lvm> lvs
(content of "report" file)
[1] fedora/~ # cat report
VG #PV #LV #SN Attr VSize VFree
fedora 1 2 0 wz--n- 19.49g 0
LV VG Attr LSize Layout Role CTime
root fedora -wi-ao---- 19.00g linear public Wed May 27 2015 08:09:21
swap fedora -wi-ao---- 500.00m linear public Wed May 27 2015 08:09:21
'lvchange --resync LV' or 'lvchange --syncaction repair LV' request the
RAID layout specific parity blocks in raid4/5/6 to be recreated or the
mirrored blocks to be copied again from the master leg/copy for raid1/10,
thus not allowing a rebuild of a particular PV.
Introduce repeatable option '--[raid]rebuild PV' to allow to request
rebuilds of specific PVs in a RaidLV which are known to contain corrupt
data (e.g. rebuild a raid1 master leg).
Add test lvchange-rebuild-raid.sh to test/shell doing rebuild
variations on raid1/10 and 5; add aux function check_status_chars
to support the new test.
- Resolves rhbz1064592
introduced with commit 8f62b7bfe5 rely on complete
defintions of the relations between the LVs of a VG.
Hence only run these checks when the complete_vg flag
is set on calls to check_lv_segments().
lvconvert failed in test lvconvert-thin-raid.sh when
calling check_lv_segments() from _read_segments() without
providing a complete definition.
General RAID and RAID segment type specific checks are added
to merge.c. New static _check_raid_seg() is called on each segment
of a RaidLV (which have just one) from check_lv_segments().
New checks caught some unititialized segment members
which are addressed here as well:
- initialize seg->region_size to 0 in lvcreate.c for raid0/raid0_meta
- initialize list seg->origin_list in lv_manip.c
When volume was lvconvert-ed to a thin-volume with external origin,
then in case thin-pool was in non-zeroing mode
it's been printing WARNING about not zeroing thin volume - but
this is wanted and expected - so nothing to warn about.
So in this particular use case WARNING needs to be suppressed.
Adding parameter support for lvcreate_params.
So now lvconvert creates 'normal thin LV' in read-only mode
(so any read will 'return 0' for a moment)
then deactivate regular thin LV and reacreate in 'final R/RW' mode
thin LV with external origin and activate again.
Before, the automatic update from older to newer version of PV extension
header happened within vg_write call. This may have caused problems under
some circumnstances where there's a code in between vg_write and vg_commit
which may have failed. In such situation, we reverted precommitted metadata
and put back the state to working version of VG metadata.
However, we don't have revert for PV write operation at the moment. So
if we updated PV headers already and we reverted vg_write due to failure
in subsequent code (before vg_commit), we ended up with lost VG metadata
(because old metadata pointers got reset by the PV write operation).
To minimize problematic situations here, we should put vg_write and
vg_commit that is done after PV header rewrites as close to each
other as possible.
This patch moves the automatic PV header rewrite for new extension
header part from vg_write to _vg_read where it's done the same way
as we do any other VG repairs if detected during VG read operation
(under VG write lock).
If the VG holding the global lock is removed, we can indicate
that as the reason for not being able to acquire the global
lock in subsequent error messages, and can suggest enabling
the global lock in another VG. (This helpful error message
will go away if the global lock is enabled in another VG,
or if lvmlockd is restarted.)
In some cases, the command will update VG metadata
in lvmetad without writing it. In these cases there
is no vg->vg_committed and it should use 'vg' directly.
This happens when the command finds that the lvmetad
VG has been invalidated, rereads the metadata from disk,
then updates lvmetad with that metadata. This happens
often with lvmlockd or foreign VGs, and can happen without
lvmlockd if a previous command fails after invalidating
the VG in lvmetad.
Commit 3928c96a37 introduced
new defaults for raid number of stripes, which may cause
backwards compatibility issues with customer scripts.
Adding configurable option 'raid_stripe_all_devices' defaulting
to '0' (i.e. off = new behaviour) to select the old behaviour
of using all PVs in the VG or those provided on the command line.
In case any scripts rely on the old behaviour, just set
'raid_strip_all_devices = 1'.
- resolves rhbz1354650
This fixes a regression from commit a7c45ddc5, which moved
the lvmetad VG update from vg_commit() to unlock_vg().
The lvmetad VG update needs to send the version of metadata
that was committed rather than sending the state of struct 'vg'.
The 'vg' may have been partially modified since vg_commit(),
and contain non-committed metadata that shouldn't be sent
to lvmetad.
Any failing stripes in raid0/raid0_meta type LVs cause data loss,
thus replacement via 'lvconvert --replace...' does not make sense.
Patch prohibits replacement on raid0/raid0_meta LVs.
- resolves rhbz1356734
Commit ca878a3426 changed behavior
or resize operation. Later the code has been futher changed
to skip fs resize completely when size of LV is already matching
and finaly at the most recent resize changeset for resize the
check for matching size has been eliminated as well so we ended
with a request call to resize fs to 0 size in some cases.
This commit reoders some test so the prompt happens just once before
resize of possibly 2 related volumes.
Also extra test for having LV already given size is added, and
whole metadata update is skipped for this case as the only
result would be an increment of seqno.
However the filesystem is still resized when requested,
so if the LV has some size and the resize is resolved to
the same size, the filesystem resize is called so in case FS
would not match, the resize will happen.
A livelock occurs on extension in lv_manip when adjusting the region size,
which doesn't apply to any raid0/raid0_meta LVs (these don't have a bitmap).
Fix by prohibiting the region size adjustment on any such LVs.
- resolves rhbz1354604
An unconditional access to the non-existing MetaLV of a raid0 LV in
lv_raid_remove_missing() was causing the segfault.
Only call log_debug() on replacements of existing MetaLVs.
- resolves rhbz1354646
When logging to epoch files we would like to prevent creating too large
log files otherwise a spining command could fulfill available space
very easily and quickly.
Limit for to 100000 per command.
This patch fixes link validation for used thin-pool.
Udev rules correctly creates symlinks only for unused new thin-pool.
Such thin-pool can be used by foreing apps (like Docker) thus
has /dev/vg/lv link.
However when thin-pool becomes used by thinLV - this link is no
longer exposed to user - but internal verfication missed this
and caused messages like this to be printed upon 'vgchange -ay':
The link /dev/vg/pool should have been created by udev but it was not
found. Falling back to direct link creation.
And same with 'vgchange -an':
The link /dev/vg/pool should have been removed by udev but it is still
present. Falling back to direct link removal.
This patch ensures only unused thin-pool has this link.
Apply the same idea as vg_update.
Before doing the VG remove on disk, invalidate
the VG in lvmetad. After the VG is removed,
remove the VG in lvmetad. If the command fails
after removing the VG on disk, but before removing
the VG metadata from lvmetad, then a subsequent
command will see the INVALID flag and not use the
stale metadata from lvmetad.
Previously, a command sent lvmetad new VG metadata in vg_commit().
In vg_commit(), devices are suspended, so any memory allocation
done by the command while sending to lvmetad, or by lvmetad while
updating its cache could deadlock if memory reclaim was triggered.
Now lvmetad is updated in unlock_vg(), after devices are resumed.
The new method for updating VG metadata in lvmetad is in two phases:
1. In vg_write(), before devices are suspended, the command sends
lvmetad a short message ("set_vg_info") telling it what the new
VG seqno will be. lvmetad sees that the seqno is newer than
the seqno of its cached VG, so it sets the INVALID flag for the
cached VG. If sending the message to lvmetad fails, the command
fails before the metadata is committed and the change is not made.
If sending the message succeeds, vg_commit() is called.
2. In unlock_vg(), after devices are resumed, the command sends
lvmetad the standard vg_update message with the new metadata.
lvmetad sees that the seqno in the new metadata matches the
seqno it saved from set_vg_info, and knows it has the latest
copy, so it clears the INVALID flag for the cached VG.
If a command fails between 1 and 2 (after committing the VG on disk,
but before sending lvmetad the new metadata), the cached VG retains
the INVALID flag in lvmetad. A subsequent command will read the
cached VG from lvmetad, see the INVALID flag, ignore the cached
copy, read the VG from disk instead, update the lvmetad copy
with the latest copy from disk, (this clears the INVALID flag
in lvmetad), and use the correct VG metadata for the command.
(This INVALID mechanism already existed for use by lvmlockd.)
Simplify code around _do_get_report_selection - remove "expected_idxs[]"
argument which is superfluous and add "allow_single" switch instead to
allow for recognition of "--configreport <report_name> -S" as well as
single "-S" if needed.
Null pointer dereferences (FORWARD_NULL) /safe/guest2/covscan/LVM2.2.02.158/tools/reporter.c: 961 in _do_report_get_selection()
Null pointer dereferences (FORWARD_NULL) Dereferencing null pointer "single_args".
Uninitialized variables (UNINIT) /safe/guest2/covscan/LVM2.2.02.158/tools/toollib.c: 3520 in _process_pvs_in_vgs()
Uninitialized variables (UNINIT) Using uninitialized value "do_report_ret_code".
Null pointer dereferences (REVERSE_INULL) /safe/guest2/covscan/LVM2.2.02.158/libdm/libdm-report.c: 4745 in dm_report_output()
Null pointer dereferences (REVERSE_INULL) Null-checking "rh" suggests that it may be null, but it has already been dereferenced on all paths leading to the check.
Incorrect expression (MISSING_COMMA) /safe/guest2/covscan/LVM2.2.02.158/lib/log/log.c: 280 in _get_log_level_name()
Incorrect expression (MISSING_COMMA) In the initialization of "log_level_names", a suspicious concatenated string ""noticeinfo"" is produced.
Null pointer dereferences (FORWARD_NULL) /safe/guest2/covscan/LVM2.2.02.158/tools/reporter.c: 816 in_get_report_options()
Null pointer dereferences (FORWARD_NULL) Comparing "mem" to null implies that "mem" might be null.
This reverts commit fa69ed0bc8.
This code sometimes expects to be presented with a read-only filesystem
(during some boot sequences for example) and copes appropriately with
this and it should not lead to expected error messages that might cause
unnecessary alarm.
lv_name arg is only used without known LV for resolving '*lv'.
Once we know *lv, never use lv_name ever again.
So setting it when passing *lv has not needed.
Add code to support more LVs to be resized through a same code path
using a single lvresize_params struct.
(Now it's used for thin-pool metadata resize,
next user will be snapshot virtual resize).
Update code to adjust percent amount resize for use_policies.
Properly activate inactive thin-pool in case of any pool resize
as the command should not 'deffer' this operation to next activation.
Use common API design and pass just LV pointer to lv_manip.c functions.
Read cmd struct via lv->vg->cmd when needed.
Also do not try to return EINVALID_CMD_LINE error when we
have already openned VG - this error code can only be returned before
locking VG.
We have only 2 users of _lv_active() - one was already checking for ==1
while the other use (_lv_is_active()) could have take '-1' as a sign of having
an LV active. So return 0 and log_debug also the reason while detection
has failed (i.e. in case --driverload n - it's kind of expectable,
but might have confused user seeing just <backtrace>).
This fixes commit f50d4011cd which
introduced a problem when using older lvm2 code with newer libdm.
In this case, the old LVM didn't recognize new _LOG_BYPASS_REPORT flag
that libdm-report code used. This ended up with no output at all
from libdm where log_print_bypass_report was called because the
_LOG_BYPASS_REPORT was not masked properly in lvm2's print_log fn
which was called as callback function for logging.
With this patch, the lvm2 registers separate print_log_libdm logging
function for libdm instead. The print_log_libdm is exactly the same
as print_log (used throughout lvm2 code) but it checks whether we're
printing common line on output where "common" means not going to stderr,
not a warning and not an error and if we are, it adds the
_LOG_BYPASS_REPORT flag so the log_print goes directly to output, not
to any log report.
So this achieves the same goal as in f50d4011cd,
just doing it in a way that newer libdm is still compatible with older
lvm2 code (libdm-report is the only code using log_print).
Looking at the opposite mixture - older libdm with newer lvm2 code,
that won't be compilable because the new log report functionality
that is in lvm2 also requires new dm_report_group_* libdm functions
so we don't need to care here.
Move code from original print_log fn to a separate _vprint_log function
that accepts va_list and make print_log a wrapper over _vprint_log.
The print_log just initializes the va_list and uses it for _vprint_log
call now. This way, we can reuse _vprint_log if needed.
Previously, vgcfgrestore would attempt to vg_remove the
existing VG from lvmetad and then vg_update to add the
restored VG. But, if there was a failure in the command
or with vg_update, the lvmetad cache would be left incorrect.
Now, disable lvmetad before the restore begins, and then
rescan to populate lvmetad from disk after restore has
written the new VG to disk.
log_print is used during cmd line processing to log the result of the
operation (e.g. "Volume group vg successfully changed" and similar).
We don't want output from log_print to be interleaved with current
reports from group where log is reported as well. Also, the information
printed by log_print belongs to the log report too, so it should be
rerouted to log report if it's set.
Since the code in libdm-report which is responsible for doing the report
output uses log_print too, we need to use a different kind of log_print
which bypasses any log report currently used for logging (...simply,
we can't call log_print to output the log report itself which in turn
would again reroute to report - the report would never get on output
this way).
This patch adds structures and functions to reroute error and warning
logs to log report, if it's set.
There are 5 new functions:
- log_set_report
Set log report where logging will be rerouted.
- log_set_report_context
Set context globally so any report_cmdlog call will use it.
- log_set_report_object_type
Set object type globally so any report_cmdlog call will use it.
- log_set_report_object_name_and_id
Set object ID and name globally so any report_cmdlog call will use it.
- log_set_report_object_group_and_group_id
Set object group ID and name globally so any report_cmdlog call will use it.
These functions will be called during LVM command processing so any logs
which are rerouted to log report contain proper information about current
processing state.
lvm fullreport executes 5 subreports (vg, pv, lv, pvseg, seg) per each VG
(and so taking one VG lock each time) within one command which makes it
easier to produce full report about LVM entities.
Since all 5 subreports for a VG are done under a VG lock, the output is
more consistent mainly in cases where LVM entities may be changed in
parallel.
New report/output_format configuration sets the output format used
for all LVM commands globally. Currently, there are 2 formats
recognized:
- basic (the classical basic output with columns and rows, used by default)
- json (output is in json format)
Add new --reportformat option and new report_format_init function that
checks this option and creates new report group accordingly, also
preparing log report handle and adding it to the report group just
created.
This is a preparation for new CMDLOG report type which is going to be
used for reporting LVM command log.
The new report type introduces several new fields (log_seq_num, log_type,
log_context, log_object_type, log_object_group, log_object_id, object_name,
log_message, log_errno, log_ret_code) as well as new configuration settings
to set this report type (report/command_log_sort and report/command_log_cols
lvm.conf settings).
This patch also introduces internal report_cmdlog helper function
which is a wrapper over dm_report_object to report command log via
CMDLOG report type and which is going to be used throughout the code
to report the log items.
This fixes a problem in commit ae0a8740c. The problem
in that commit was that all existing PVs are initially
dropped from lvmetad. This works if the VG is updated
at the end, which replaces the dropped PVs, but if the
rescan finds that the VG seqno is unchanged, it leaves
the cached VG in place. So, we should only drop the
existing PVs in lvmetad when the VG is going to be updated.
Original code missed to catch all apperances of SIGINT.
Also enhance logging when running in shell without tty.
Accept this regex as valid input:
'^[ ^t]*([Yy]([Ee]([Ss]|)|)|[Nn]([Oo]|))[ ^t]*$'
Some commands scan labels to populate lvmcache multiple
times, i.e. lvmcache_init, scan labels to fill lvmcache,
lvmcache_destroy, then later repeat
Each time labels are scanned, duplicates are detected,
and preferred devices are chosen. Each time this is done
within a single command, we want to choose the same
preferred devices. So, check for existing preferences
when choosing preferred devices.
This also fixes a problem with the list of unused duplicate
devs when run in an lvm shell. The devs had been allocated
from cmd memory, resulting in invalid list entries between
commands.
A number of places are working on a specific dev when they
call lvmcache_info_from_pvid() to look up an info struct
based on a pvid. In those cases, pass the dev being used
to lvmcache_info_from_pvid(). When a dev is specified,
lvmcache_info_from_pvid() will verify that the cached
info it's using matches the dev being processed before
returning the info. Calling code will not mistakenly
get info for the wrong dev when duplicate devs exist.
This confusion was happening when scanning labels when
duplicate devs existed. label_read for the first dev
would add an info struct to lvmcache for that dev/pvid.
label_read for the second dev would see the pvid in
lvmcache from first dev, and mistakenly conclude that
the label_read from the second dev can be skipped
because it's already been done. By verifying that the
dev for the cached pvid matches the dev being read,
this mismatch is avoided and the label is actually read
from the second duplicate.
If a command gets stuck during an lvmetad update, lvmetad
will cancel that update after the timeout. The next command
to check the lvmetad will see that lvmetad needs to be
populated because lvmetad will return token of "none" after
a timed out update (same as when lvmetad is not populated
at all after starting.)
If a command gets an error during an lvmetad update, it
will now just quit and leave its updating token in place.
That update will be cancelled after the timeout.
Treat loop device created with 'losetup -P' as regular
partitioned device - so if it has partition table,
prevent its usage in commands like 'pvcreate'.
Before 'pvcreate /dev/loop0' could have erased and formated as PV,
after this patch, device is filtered out and cannot be used.
Before this fix, when reporting 'lvm devtypes', the report was
initialized with incorrect reserved values - the ones used for
pvs/vgs/lvs report were used instead of NULL value (because devtypes
doesn't have any reserved values).
For example, trying to (incorrectly) use lv_name for the -S|--select
with lvm devtypes which doesn't have this field at all:
Before this patch (internal error issued):
$ lvm devtypes -S 'lv_name=lvol0'
Internal error: _check_reserved_values_supported: field-specific reserved value of type 0x0 for field not supported
Internal error: dm_report_init_with_selection: trying to register unsupported reserved value type, skipping report selection
DevType MaxParts Description
aoe 16 ATA over Ethernet
ataraid 16 ATA Raid
bcache 1 bcache block device cache
...
With this patch applied (correct error displayed about
unrecognized selection field):
$ lvm devtypes -S 'lv_name=lvol0'
Device Types Fields
-------------------
devtype_name - Name of Device Type exactly as it appears in /proc/devices. [string]
devtype_max_partitions - Maximum number of partitions. (How many device minor numbers get reserved for each device.) [number]
devtype_description - Description of Device Type. [string]
Special Fields
--------------
selected - Set if item passes selection criteria. [number]
help - Show help. [unselectable number]
? - Show help. [unselectable number]
Unrecognised selection field: lv_name
Selection syntax error at 'lv_name=lvol0'.
Use 'help' for selection to get more help.
Convert fields into using a single status ioctl call per LV.
This is a bit tricky since when there are more complicated
stacks, at this moment its undefined which values should be shown.
It's clear we need to cache more then single ioctl per LV,
but also we need to define more explicitely relation between
reported values for snapshots.
This patch is not a final state, rather a transitional step.
It should not be giving more 'worst' values then previous
many-ioctl-calls-per-lv solution.
Add function to obtain percentage value for cache lv_seg_status.
This API is rather evolving 'middle' step as the ultimate goal
is segment API fuctionality.
But first we need to be clear at reporting level which values
are needed to be reported for which LVs and segments.
Add more code to properly store status for snapshot segment
maintaining lvm2 fiction of COW and snapshot internal volumes.
The key issue here is however not though-through reporting
logic - as there is no single answer for whole line state.
It not counting with layer and we may need few more ioctl to
cover all reporting needs depending upon what is actually
needed.
In reality we need to 'cache' more ioctl status queries for
individual LVs and their segments (so they checked at most once).
The other 'hard' topic for conversion is mirror segment handling.
Also we definitelly need to relocate some logic into segment's methods,
yet it might be complex as we have not clear border between targets.
TODO: define more clearly how are reporting fields defined in case
we 'stack' volumes like - cache of stacked thin LV snapshot origin.
lv_refresh_suspend_resume() has escaped with fail ret code
after failing suspend and could have left many volumes in suspend state.
So always unconditionally call resume also when suspend has failed.
To get better control when flushing is used add extra arg when
setting up dm task.
By default now check dm device status without flush.
(At this moment this should effect only thin and cache volumes).
Also switch dev_manager_thin_pool_status() to use more
readable 'flush' parameter instead of 'no_flush'.
Check first the LV is cow before even checking it's a merging COW.
Note: previosly merging_cow was also merging origin, so without
this explicit check it used to return '1' also when passed
LV has been merging origin.
When mirror/raid called copy_percent function to return,
when 100% was supposed to be returned, wrong float 100.0 value
could have been reported back instead of dm_percent_t DM_PERCENT_100.
There is broken API somewhere, since the function here rely on
actively being modifid VG content even when doing 'lvs' operation.
(extents_copies)
This refactors the code for autoactivation. Previously,
as each PV was found, it would be sent to lvmetad, and
the VG would be autoactivated using a non-standard VG
processing function (the "activation_handler") called via
a function pointer from within the lvmetad notification path.
Now, any scanning that the command needs to do (scanning
only the named device args, or scanning all devices when
there are no args), is done first, before any activation
is attempted. During the scans, the VG names are saved.
After scanning is complete, process_each_vg is used to do
autoactivation of the saved VG names. This makes pvscan
activation much more similar to activation done with
vgchange or lvchange.
The separate autoactivate phase also means that if lvmetad
is disabled (either before or during the scan), the command
can continue with the activation step by simply not using
lvmetad and reverting to disk scanning to do the
activation.
Add support for active cache LV.
Handle --cachemode args validation during command line processing.
Rework some lvm2 internal to use lvm2 defined CACHE_MODE enums
indepently on libdm defines and use enum around the code instead
of passing and comparing strings.
A program may be using liblvm2app for simply checking a config
setting in lvm.conf. In this case, a full lvm context is not
needed, only cmd->cft (which are the config settings read from
lvm.conf).
lvm_config_find_bool() can now be passed a NULL lvm context
in which case it will only create cmd->cft, check the config
setting asked for, and destroy the cmd.
When setting up a toolcontext, the lib init function
was detecting an error when there was none, and then
it was returning an incompletely initialized cmd struct
instead of NULL. The effect was that the lib would try
to use the uninitialized cmd struct and segfault.
This would happen if a non-fatal error occurred during
cmd setup, e.g. user permission failed on lvmetad socket,
causing cmd to fall back to scanning and not use lvmetad.
The only real error condition is when create_toolcontext
returns NULL. If cmd is returned, the lib can use it.
If a command begins repopulating the lvmetad cache,
and fails part way through, it should set the disabled
state in lvmetad so other commands don't use bad data.
If a subsequent scan succeeds, the disabled state is
cleared.
If duplicate devices exist for a PV, and one device's
size matches the PV size, but the other doesn't, then
prefer the matching device.
If one device is used by an active LV, prefer that device.
When there are duplicate devices for a PV, one device
is preferred and chosen to exist in the VG. The other
devices are not used by lvm, but are displayed by pvs
with a new PV attr "d", indicating that they are
unchosen duplicate PVs.
The "duplicate" reporting field is set to "duplicate"
when the PV is an unchosen duplicate, and that field
is blank for the chosen PV.
Previously, duplicate PVs were processed as a side effect
of processing the "chosen" PV in lvmcache. The duplicate
PV would be hacked into lvmcache temporarily in place of
the chosen PV.
In the old way, we had to always process the "chosen" PV
device, even if a duplicate of it was named on the command
line. This meant we were processing a different device than
was asked for. This could be worked around by naming
multiple duplicate devs on the command line in which case
they were swapped in and out of lvmcache for processing.
Now, the duplicate devs are processed directly in their
own processing loop. This means we can remove the old
hacks related to processing dups as a side effect of
processing the chosen device. We can now simply process
the device that was named on the command line.
When the same PVID exists on two or more devices, one device
is preferred and used in the VG, and the others are duplicates
and are not used in the VG. The preferred device exists in
lvmcache as usual. The duplicates exist in a specical list
of unused duplicate devices.
The duplicate devs have the "d" attribute and the "duplicate"
reporting field displays "duplicate" for them.
'pvs' warns about duplicates, but the formal output only
includes the single preferred PV.
'pvs -a' has the same warnings, and the duplicate devs are
included in the output.
'pvs <path>' has the same warnings, and displays the named
device, whether it is preferred or a duplicate.
Wait to compare and choose alternate duplicate devices until
after all devices are scanned. During scanning, the first
duplicate dev is kept in lvmcache, and others are kept in a
new list (_found_duplicate_devs).
After all devices are scanned, compare all the duplicates
available for a given PVID and decide which is best.
If the dev used in lvmcache is changed, drop the old dev
from lvmcache entirely and rescan the replacement dev.
Previously the VG metadata from the old dev was kept in
lvmcache and only the dev was replaced.
A new config setting devices/allow_changes_with_duplicate_pvs
can be set to 0 which disallows modifying a VG or activating
LVs in it when the VG contains PVs with duplicate devices.
Set to 1 is the old behavior which allowed the VG to be
changed.
The logic for which of two devs is preferred has changed.
The primary goal is to choose a device that is currently
in use if the other isn't, e.g. by an active LV.
. prefer dev with fs mounted if the other doesn't, else
. prefer dev that is dm if the other isn't, else
. prefer dev in subsystem if the other isn't
If neither device is preferred by these rules, then don't
change devices in lvmcache, leaving the one that was found
first.
The previous logic for preferring a device was:
. prefer dev in subsystem if the other isn't, else
. prefer dev without holders if the other has holders, else
. prefer dev that is dm if the other isn't
Support parsing --chunksize option also when converting.
Now user can use cache pool created with i.e. 32K chunksize,
while in caching user can select 512K blocks.
Tool is supposed to validate cache metadata size is big enough
to support such chunk size. Otherwise error is shown.
