IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
When conditions fail on a service unit, a path unit can cause
PID 1 to busy loop as it keeps trying to activate the service unit.
To avoid this from happening, add a trigger limit to the path unit,
identical to the trigger limit we have for socket units.
Initially, let's start with a high limit and not make it configurable.
If needed, we can add properties to configure the rate limit similar
to the ones we have for socket units.
On some runs `sleep infinity` run by the user manager uses over 3M of
memory, which is higher than the MemoryHigh= set on testbloat and
testmunch. If no pgscan is generated, then systemd-oomd sorts by memory
usage which leads to a situation where testchill (using 3M) could be
targeted over testbloat (1M-2M).
Fix this by setting reasonable MemoryHigh= values for all of these test
units. Even if somehow testchill throttles a bit at 3M, testbloat and
testmunch should still be trying to use over 100M at memory and will
throttle down to 5M and 6M with the new values. This should reflect
the desired state in pgscan and memory usage during the test run.
Fixes#21684
The openssl binary is an optional dependency.
If systemd has been built with OpenSSL support, we want to test its
OpenSSL functionality.
So record a failure message in /failed if the binary is missing.
See https://github.com/systemd/systemd/pull/21724#issuecomment-992707614
Otherwise we might miss the "Device path too long" message:
```
[ 21.083274] testsuite-64.sh[374]: swapoff /dev/vda1
[ 21.089841] testsuite-64.sh[376]: ++ mktemp
[ 21.095115] testsuite-64.sh[271]: + logfile=/tmp/tmp.a1MULA35wL
[ 21.095115] testsuite-64.sh[271]: + journalctl -b -q --no-pager -o short-monotonic -p info --grep 'Device path.*vda.?'\'' too long to fit into unit name'
...
[ 21.277360] systemd[1]: testsuite-64.service: Main process exited, code=exited, status=1/FAILURE
[ 21.277508] systemd[1]: testsuite-64.service: Failed with result 'exit-code'.
...
[ 21.323500] systemd[1]: Device path '/sys/devices/pci0000:00/0000:00:03.0/0000:01:00.0/0000:02:00.0/0000:03:00.0/0000:04:00.0/0000:05:00.0/0000:06:00.0/0000:07:00.0/0000:08:00.0/0000:09:00.0/0000:0a:00.0/0000:0b:00.0/0000:0c:00.0/0000:0d:00.0/0000:0e:00.0/0000:0f:00.0/0000:10:00.0/0000:11:00.0/0000:12:00.0/0000:13:00.0/0000:14:00.0/0000:15:00.0/0000:16:00.0/0000:17:00.0/0000:18:00.0/0000:19:00.0/0000:1a:00.0/virtio0/block/vda/vda1' too long to fit into unit name, ignoring device.
```
TEST-67-INTEGRITY times out quite often, and when it passes
it does so a few seconds short of the timeout. It's a slow
qemu test, so bump the timeout.
TEST-50-DISSECT has been reported to fail in the same way
on Debian's infrastructure, again narrowly failing or passing
just short of the timeout.
This fixes the following warning:
-----
In /github/workspace/test/units/testsuite-62.sh line 39:
KERNEL_MINOR="${KERNEL_VERSION#$KERNEL_MAJOR.}"
^-----------^ SC2295 (info): Expansions inside ${..} need to be quoted separately, otherwise they match as patterns.
Did you mean:
KERNEL_MINOR="${KERNEL_VERSION#"$KERNEL_MAJOR".}"
It picks the whole content of the directory by default, but we don't
want to install .gitattributes files. Add it to all invocations, not
just the ones on subdirs with .gitattributes, so that we don't regress
in the future.
Fixes#21715
People often assigns the MAC address of the enslaved interface to e.g.
bridge interface. So, the local assignment bit should not be adjusted.
Fixes#21649.
Writing a byte to test10.socket is actually the root cause of issue #19154:
depending on the timing, it's possible that PID1 closes the socket before socat
(or nc, it doesn't matter which tool is actually used) tries to write that one
byte to the socket. In this case writing to the socket returns EPIPE, which
causes socat to exit(1) and subsequently make the test fail.
Since we're only interested in connecting to the socket and triggering the rate
limit of the socket, this patch removes the parts that write the single byte to
the socket, which should remove the race for good.
Since it shouldn't matter whether the test uses socat or nc, let's switch back
to nc and hence remove the sole user of socat. The exit status of nc is however
ignored because some versions might choke when the socket is closed
unexpectedly.
This commit adds a function which converts a bus message containing the
environment variables to a JSON object and uses this function to support
JSON formatted output for the "systemctl show-environment" command.
Fixes#21348
By default checks PSI on /proc/pressure, and causes a unit to be skipped
if the threshold is above the given configuration for the avg300
measurement.
Also allow to pass a custom timespan, and a particular slice unit to
check under.
Fixes#20139
