shaba/systemd
1
0
Fork 0
mirror of https://github.com/systemd/systemd.git synced 2024-10-30 06:25:37 +03:00
Code
7847b54814
systemd/test/units/testsuite-10.service

17 lines
634 B
SYSTEMD
Raw Normal View History

tests: add spdx license header to test unit/link/network/conf files Those are all consumed by our parser, so they all support comments. I was considering whether they should have a license header at all, but in the end I decided to add it because those files are often created by copying parts of real unit files. And if the real ones have a license, then those might as well. It's easier to add it than to make an exception.
2021-10-17 19:07:22 +03:00
# SPDX-License-Identifier: LGPL-2.1-or-later
test: move TEST-10-ISSUE-2467 setup to static files
2019-12-09 22:42:48 +03:00
[Unit]
Description=TEST-10-ISSUE-2467
[Service]
test: make sure to reset state before starting integration tests
2019-12-13 14:34:41 +03:00
ExecStartPre=rm -f /failed /testok
test: move TEST-10-ISSUE-2467 setup to static files
2019-12-09 22:42:48 +03:00
Type=oneshot
test: fix TEST-10-ISSUE-2467 Depending on the timing, socat will either get ECONNREFUSED oder EPIPE from systemd. The latter will cause it to exit(1) and subsequently the test to fail. We are not actually interested in the return code of socat though. The test is supposed to check, whether rate limiting of a socket unit works properly. So ignore any failures from the socat invocation and instead check, if test10.socket is in state "failed" with result "trigger-limit-hit" after it has been triggered. TriggerLimitIntervalSec= by default is set to 2s. A "sleep 10" should give systemd enough time even on slower machines, to reach the trigger limit. For better readability, break the test into separate ExecStart lines. Fixes #19154.
2021-08-09 20:45:48 +03:00
ExecStart=rm -f /tmp/nonexistent
ExecStart=systemctl start test10.socket
TEST-10: don't attempt to write a byte to the socket Writing a byte to test10.socket is actually the root cause of issue #19154: depending on the timing, it's possible that PID1 closes the socket before socat (or nc, it doesn't matter which tool is actually used) tries to write that one byte to the socket. In this case writing to the socket returns EPIPE, which causes socat to exit(1) and subsequently make the test fail. Since we're only interested in connecting to the socket and triggering the rate limit of the socket, this patch removes the parts that write the single byte to the socket, which should remove the race for good. Since it shouldn't matter whether the test uses socat or nc, let's switch back to nc and hence remove the sole user of socat. The exit status of nc is however ignored because some versions might choke when the socket is closed unexpectedly.
2021-11-17 10:13:04 +03:00
ExecStart=-nc -w20 -U /run/test.ctl
test: fix TEST-10-ISSUE-2467 Depending on the timing, socat will either get ECONNREFUSED oder EPIPE from systemd. The latter will cause it to exit(1) and subsequently the test to fail. We are not actually interested in the return code of socat though. The test is supposed to check, whether rate limiting of a socket unit works properly. So ignore any failures from the socat invocation and instead check, if test10.socket is in state "failed" with result "trigger-limit-hit" after it has been triggered. TriggerLimitIntervalSec= by default is set to 2s. A "sleep 10" should give systemd enough time even on slower machines, to reach the trigger limit. For better readability, break the test into separate ExecStart lines. Fixes #19154.
2021-08-09 20:45:48 +03:00
# TriggerLimitIntervalSec= by default is set to 2s. A "sleep 10" should give
# systemd enough time even on slower machines, to reach the trigger limit.
ExecStart=sleep 10
ExecStart=sh -x -c 'test "$(systemctl show test10.socket -P ActiveState)" = failed'
Revert "core: Propagate condition failed state to triggering units." This reverts commit 12ab94a1e4961a39c32efb60b71866ab588d3ea2.
2021-12-17 21:39:29 +03:00
ExecStart=sh -x -c 'test "$(systemctl show test10.socket -P Result)" = trigger-limit-hit'
test: fix TEST-10-ISSUE-2467 Depending on the timing, socat will either get ECONNREFUSED oder EPIPE from systemd. The latter will cause it to exit(1) and subsequently the test to fail. We are not actually interested in the return code of socat though. The test is supposed to check, whether rate limiting of a socket unit works properly. So ignore any failures from the socat invocation and instead check, if test10.socket is in state "failed" with result "trigger-limit-hit" after it has been triggered. TriggerLimitIntervalSec= by default is set to 2s. A "sleep 10" should give systemd enough time even on slower machines, to reach the trigger limit. For better readability, break the test into separate ExecStart lines. Fixes #19154.
2021-08-09 20:45:48 +03:00
ExecStart=sh -x -c 'echo OK >/testok'
Copy Permalink