IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This is necessary for non-ipv4ll hosts to communicate with ipv4ll-only hosts on the same link. Defaults
to being enabled, but can be opted out.
See: <http://avahi.org/wiki/AvahiAutoipd#Routes>
The following bond options are supported by this patch.
MIIMonitorSec:
Specifies the frequency in milli-seconds that MII link
monitoring will occur.
UpDelaySec:
Specifies the delay time in milli-seconds to enable a link
after a link up status has been detected.
DownDelaySec:
Specifies the delay time in milli-seconds to disable a link
after a link failure has been detected.
changes:
1. Added gconf variables.
2. man page
conf:
[NetDev]
Name=bond1
Kind=bond
[Bond]
Mode=802.3ad
TransmitHashPolicy=layer2+3
LacpduTransmitRate=fast
MIIMonitorSec=1s
UpDelaySec=2s
DownDelaySec=8s
cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer2+3 (2)
MII Status: up
MII Polling Interval (ms): 1000
Up Delay (ms): 2000
Down Delay (ms): 8000
802.3ad info
LACP rate: fast
Min links: 0
Aggregator selection policy (ad_select): stable
bond bond1 has no active aggregator
[tomegun: rephrased manpage, dropped bond_ prefix from variables]
LacpduTransmitRate
option specifies the rate in which link partner to transmit
LACPDU packets in 802.3ad mode. Possible values
slow : Request partner to transmit LACPDUs every 30 seconds
fast : Request partner to transmit LACPDUs every 1 second
The default is slow.
chages:
1. Added enum bond_lacp_rate_table
2. gperf LacpduTransmitRate
Test:
conf file:
[NetDev]
Name=bond1
Kind=bond
[Bond]
Mode=802.3ad
LacpduTransmitRate=fast
test:
cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer2+3 (2)
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
802.3ad info
LACP rate: fast
Min links: 0
Aggregator selection policy (ad_select): stable
bond bond1 has no active aggregator
[tomegun: renamed from LacpduTransmitRate to LACPTransmitRate, manpage fixes and
dropped bond_ prefix from variables]
This patch adds support the transmit hash policy to use
for slave selection in balance-xor, 802.3ad, and tlb modes
layer2, layer3+4, layer2+3, encap3+4, encap3+4
Added:
1. BondXmitHashPolicy
2. conf param TransmitHashPolicy
Test conf:
[NetDev]
Name=bond1
Kind=bond
[Bond]
Mode=802.3ad
TransmitHashPolicy=layer2+3
test output:
cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer2+3 (2)
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
802.3ad info
LACP rate: slow
Min links: 0
Aggregator selection policy (ad_select): stable
bond bond1 has no active aggregator
[tomegun: dropped bond_ prefix from new Bond variable, drop repeated man-page section]
A system that is running on a logical partition (LPAR) provided by
PR/SM has access to physical hardware (except CPU). It is true that
PR/SM abstracts the hardware, but only for sharing purposes.
Details are statet at:
http://publib.boulder.ibm.com/infocenter/eserver/v1r2/topic/eicaz/eicazzlpar.htm
-->--
In other words, PR/SM transforms physical resources into virtual resources so
that many logical partitions can share the same physical resources.
--<--
Still, from the OS point of view, the shared virtual resource is real
hardware. ConditionVirtualization must be set to false if the OS runs
directly on PR/SM (e.g. in an LPAR).
[zj: reorder code so that variables are not allocated when #if-def is
false. Add commit message.]
Previously existing scheme where the file name would be based on
the source was just too ugly and unpredicatable. Now there are
only two options:
1. just one file (until rotation),
2. one file per source host, using the hostname as filename part.
For the cases where the source is specified by the user, only
option one is allowed, and the full of the file must be specified.
It appears there is no good way to decide whether or not broadcasts should be enabled,
there is hardware that must have broadcast, and there are networks that only allow
unicast. So we give up and make this configurable.
By default, unicast is used, but if the kernel were to inform us abotu certain
interfaces requiring broadcast, we could change this to opt-in by default in
those cases.
Vendor Class Identifier be used by DHCP clients to identify
their vendor type and configuration. When using this option,
vendors can define their own specific identifier values, such
as to convey a particular hardware or operating system
configuration or other identifying information.
Vendor-specified DHCP options—features that let administrators assign
separate options to clients with similar configuration requirements.
For example, if DHCP-aware clients for example we want to separate
different gateway and option for different set of people
(dev/test/hr/finance) in a org or devices for example web/database
servers or let's say in a embedded device etc and require a different
default gateway or DNS server than the rest of clients.
Now route metric can be configuted via conf file:
example conf:
[Match]
Name=em1
[Route]
Gateway=192.168.1.12
Metric=10
Test:
ip route output
default via 192.168.1.12 dev em1 metric 10
[tomegun: squash TODO update and reword man page a bit]
An administrator might want to block a certain sysusers config file from
being executed, e.g. to block the creation of a certain user.
Only a relatively short description is added in the man page, since
overrides should be relatively rare.
It is annoying when we have dead links on fd.o.
Add project='man-pages|die-net|archlinux' to <citerefentry>-ies.
In generated html, add external links to
http://man7.org/linux/man-pages/man, http://linux.die.net/man/,
https://www.archlinux.org/.
By default, pages in sections 2 and 4 go to man7, since Michael
Kerrisk is the autorative source on kernel related stuff.
The rest of links goes to linux.die.net, because they have the
manpages.
Except for the pacman stuff, since it seems to be only available from
archlinux.org.
Poor gummiboot gets no link, because gummitboot(8) ain't to be found
on the net. According to common wisdom, that would mean that it does
not exist. But I have seen Kay using it, so I know it does, and
deserves to be found. Can somebody be nice and put it up somewhere?
This patch adds supports networkd to configure bond mode
during creation via persistent conf. Mode can be configured
with conf param 'Mode'. A new section Bond is added to the
conf to support bond mode.
These modes can be configured now.
balance-rr
active-backup
balance-xor
broadcast
802.3ad
balance-tlb
balance-alb
Example conf file: test-bond.conf
[NetDev]
Name=bond1
Kind=bond
[Bond]
Mode=balance-xor
Test case:
1. start networkd service:
12: bond1: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc
noqueue state UNKNOWN mode DEFAULT group default
link/ether 22:89:6c:47:23:d2 brd ff:ff:ff:ff:ff:ff
2. find bond mode:
cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: load balancing (xor)
Transmit Hash Policy: layer2 (0)
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
Changes:
1. Added file networkd-bond.c
2. Bond mode enum BondMode
3. conf section [Bond]
[tomegun: whitespace]
As Zbigniew pointed out a new ConditionFirstBoot= appears like the nicer
way to hook in systemd-firstboot.service on first boots (those with /etc
unpopulated), so let's do this, and get rid of the generator again.